Poulan 411287 manual Tractor, Blade Removal See Fig, Battery

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

828

16

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Useonlyareplacementblade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 11)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

BLADE

STAR

 

 

 

 

02

545

 

 

 

 

MANDREL

 

 

ASSEMBLY

BLADE BOLT

CENTER

 

(SPECIAL)

HOLE

 

FIG. 11

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PB195H42LT ModelSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System Reverse Operation System ROSTo Operate Mower See Fig To Operate on HillsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP RunningMaintenance Lubrication ChartBattery TractorBlade Removal See Fig Important Special blade bolt is heat treatedEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig ALL Mower Pulley Grooves Important Check Belt for Proper RoutingCollar L onto guide and secure with retainer spring K To Level Mower To obtain the best cutting results, the mower blades shouldBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Alon THI Dotted Line REE LopeOutdoor Products Customer Service Dept HOPCanada contact Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAAutorisé Dept Service Customer Products Outdoor Canada AuGarantie cette de exclus sont normal l’entretien et Degrés Dentretien Remarques Dépannage DE Guide Défectueux estRalenti GAZ DES Commande DU Commande LA Régler PourEntreposage Réglages ET Révision Fig la Voir Calandre LA ET Capot LE Enlever PourDES L’AMPOULE Remplacer Pour Fig la Voir Batterie LA ReplacerTionrecdi Carrossage AVANT/ Roues DES ConvergenceLA DE L’ALIGNEMENT Régler Pour Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour FIG LA VoirTondeuse DE Lame DE Mentnetraî ’EN Courroie LA Remplacer PourTondeuse LA Niveau LE Ajuster Pour 24 .FIG22 .FIG 23 .FIG20 .FIG 18 .FIG 19 .FIG17 .FIG Place en bien est courroie la que vous-Assurez ImportantCourroie LA ET Tondeuse LA Installer Reglages ET RevisionFig Voir Tondeuse LA Enlever PourLigne EN Installé D’ESSENCE Filtre EntretienFig La Voir Coupe DE Plateau DU Lavage DE Raccord Fig la Voir’ALLUMAGE Bougie SilencieuxMoteur DE D’HUILE Filtre AIR À FiltreFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau O I T a D N a M M O C E RUtilisation Chaque Avant Utilisation Transmission LA PurgerTonte DE Conseils 10 .FIGAccessoires Autres Moteur LE Démarrer Pour’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE VérifierFig la Voir Tondeuse LA Utiliser Pour MAR EN Fonctionnement DE SystèmeTracteur LE Transporter Pour Pentes LES Dans Utiliser PourGAZ DES Commande LA Utiliser Pour Fig la Voir Arrêter PourFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour Reculer Pour ET Avancer PourTracteur Votre Connaissez Propriété la de lendommagement Correctement Sont Courroies LES MontageToutes SI Vérifier Toutes SI Vérifier Fig la Voir Batterie LA Vérifier Desmancom Des fonction la et mentceplalem connaîtrePour mentnetionfonc tionsec la Voir Rouler Faisant LE EN Palette LA DE Tracteur LE Retirer PourDU Tracteur LE Sortir Pour Pour Exigés Outils LESEt 2 .Figs les Voir Siège LE Ajustez Tionrecdi DE Volant LE FixerMontar SIN Piezas U1R Dimension SommaireGarantie CCA .MIN AMP/HRGénéral Entretien Tracteurs des sécurité toute’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationLES Dans Fonctionnement PentesTracteurs des sécurité toute en l’utilisation pour Conseils Avertissement

411287 specifications

The Poulan 411287 is a robust outdoor power tool designed to meet the needs of homeowners and landscaping professionals alike. This high-performance gas-powered chainsaw is especially popular for its reliability, versatility, and user-friendly features, making it an ideal choice for both cutting firewood and tackling larger landscaping tasks.

One of the standout features of the Poulan 411287 is its powerful engine. Equipped with a 40cc two-stroke engine, this chainsaw delivers impressive performance while ensuring efficient fuel consumption. The engine's design minimizes emissions, aligning with contemporary environmental standards and making it a more eco-friendly option in the chainsaw market.

The chainsaw also incorporates a 16-inch steel bar and chain, providing ample cutting capacity for various applications. This length strikes a perfect balance, allowing users to handle everything from small branches to medium-sized trees without compromising ease of use. The bar and chain design ensures smooth cutting action, reducing kickback and improving operator safety.

Ergonomics play a crucial role in the Poulan 411287's design. The chainsaw is equipped with a comfortable grip that minimizes vibrations, making it less taxing on the user's hands during extended use. Additionally, the lightweight construction enhances maneuverability, allowing users to work for longer periods without fatigue.

Another noteworthy feature is the automatic chain oiler, which ensures the chain is consistently lubricated during operation. This not only prolongs the life of the chainsaw but also enhances cutting efficiency. The tool-less chain tensioning system further simplifies maintenance, allowing users to quickly adjust the chain for optimal performance without the need for additional tools.

Furthermore, the Poulan 411287 is designed with a translucent fuel tank, enabling users to monitor fuel levels at a glance. This convenient feature helps prevent unexpected interruptions during tasks, ensuring productivity is maximized.

In conclusion, the Poulan 411287 is a well-rounded chainsaw that combines power, ease of use, and innovative features. Whether for the occasional homeowner or the dedicated landscaping professional, it provides a reliable solution for a wide range of cutting tasks. With its focus on efficiency and user comfort, the Poulan 411287 is undoubtedly a valuable addition to any outdoor toolkit.
Top Page Image Contents