Poulan 411287 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 24

SERVICE AND ADJUSTMENTS

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

REPLACING BATTERY (See Fig. 30)

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with bolt and nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining bolt and nut. Tighten securely.

•Lower seat pan.

SEAT PAN

02602

TERMINAL

 

NUT

COVER

 

 

BOLT

 

 

POSITIVE

 

NEGATIVE

(RED)

 

 

(BLACK)

CABLE

 

 

CABLE

 

02603

Fig. 30

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

01536

FIG. 31

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PB195H42LT ModelSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System Reverse Operation System ROSTo Operate Mower See Fig To Operate on HillsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP RunningMaintenance Lubrication ChartBattery TractorBlade Removal See Fig Important Special blade bolt is heat treatedEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig Service and Adjustments To Install Mower See FigTo Remove Mower See Fig Important Check Belt for Proper Routing ALL Mower Pulley GroovesCollar L onto guide and secure with retainer spring K To Level Mower To obtain the best cutting results, the mower blades shouldBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Alon THI Dotted Line REE LopeOutdoor Products Customer Service Dept HOPCanada contact Stevens Creek Road Terry Fox Way Augusta, GA 30907 USADept Service Customer Products Outdoor Canada Au AutoriséGarantie cette de exclus sont normal l’entretien et Degrés Dentretien Remarques Dépannage DE Guide Défectueux estRalenti DU Commande LA Régler Pour GAZ DES CommandeEntreposage Réglages ET Révision Fig la Voir Calandre LA ET Capot LE Enlever PourDES L’AMPOULE Remplacer Pour Fig la Voir Batterie LA ReplacerCarrossage AVANT/ Roues DES Convergence TionrecdiLA DE L’ALIGNEMENT Régler Pour Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour FIG LA VoirTondeuse DE Lame DE Mentnetraî ’EN Courroie LA Remplacer PourTondeuse LA Niveau LE Ajuster Pour 24 .FIG22 .FIG 23 .FIG20 .FIG 18 .FIG 19 .FIG17 .FIG Place en bien est courroie la que vous-Assurez ImportantCourroie LA ET Tondeuse LA Installer Reglages ET RevisionFig Voir Tondeuse LA Enlever PourLigne EN Installé D’ESSENCE Filtre EntretienFig La Voir Coupe DE Plateau DU Lavage DE Raccord Fig la Voir’ALLUMAGE Bougie SilencieuxMoteur DE D’HUILE Filtre AIR À FiltreFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETO I T a D N a M M O C E R Lubrification DE TableauUtilisation Chaque Avant Utilisation Transmission LA PurgerTonte DE Conseils 10 .FIGAccessoires Autres Moteur LE Démarrer Pour’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE VérifierFig la Voir Tondeuse LA Utiliser Pour MAR EN Fonctionnement DE SystèmeTracteur LE Transporter Pour Pentes LES Dans Utiliser PourGAZ DES Commande LA Utiliser Pour Fig la Voir Arrêter PourFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour Reculer Pour ET Avancer PourTracteur Votre Connaissez Propriété la de lendommagement Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier Fig la Voir Batterie LA Vérifier Desmancom Des fonction la et mentceplalem connaîtrePour mentnetionfonc tionsec la Voir Rouler Faisant LE EN Palette LA DE Tracteur LE Retirer PourDU Tracteur LE Sortir Pour Pour Exigés Outils LESEt 2 .Figs les Voir Siège LE Ajustez Tionrecdi DE Volant LE FixerMontar SIN Piezas U1R Dimension SommaireGarantie CCA .MIN AMP/HRGénéral Entretien Tracteurs des sécurité toute’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils Avertissement

411287 specifications

The Poulan 411287 is a robust outdoor power tool designed to meet the needs of homeowners and landscaping professionals alike. This high-performance gas-powered chainsaw is especially popular for its reliability, versatility, and user-friendly features, making it an ideal choice for both cutting firewood and tackling larger landscaping tasks.

One of the standout features of the Poulan 411287 is its powerful engine. Equipped with a 40cc two-stroke engine, this chainsaw delivers impressive performance while ensuring efficient fuel consumption. The engine's design minimizes emissions, aligning with contemporary environmental standards and making it a more eco-friendly option in the chainsaw market.

The chainsaw also incorporates a 16-inch steel bar and chain, providing ample cutting capacity for various applications. This length strikes a perfect balance, allowing users to handle everything from small branches to medium-sized trees without compromising ease of use. The bar and chain design ensures smooth cutting action, reducing kickback and improving operator safety.

Ergonomics play a crucial role in the Poulan 411287's design. The chainsaw is equipped with a comfortable grip that minimizes vibrations, making it less taxing on the user's hands during extended use. Additionally, the lightweight construction enhances maneuverability, allowing users to work for longer periods without fatigue.

Another noteworthy feature is the automatic chain oiler, which ensures the chain is consistently lubricated during operation. This not only prolongs the life of the chainsaw but also enhances cutting efficiency. The tool-less chain tensioning system further simplifies maintenance, allowing users to quickly adjust the chain for optimal performance without the need for additional tools.

Furthermore, the Poulan 411287 is designed with a translucent fuel tank, enabling users to monitor fuel levels at a glance. This convenient feature helps prevent unexpected interruptions during tasks, ensuring productivity is maximized.

In conclusion, the Poulan 411287 is a well-rounded chainsaw that combines power, ease of use, and innovative features. Whether for the occasional homeowner or the dedicated landscaping professional, it provides a reliable solution for a wide range of cutting tasks. With its focus on efficiency and user comfort, the Poulan 411287 is undoubtedly a valuable addition to any outdoor toolkit.
Top Page Image Contents