Poulan 411287 manual Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)1/2" wrench Utility knife

(2)3/4" wrench Tire pressure gauge Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

 

INSERT

 

5/16 HEX BOLT

 

5/16 LOCK WASHER

 

LARGE FLAT WASHER

 

STEERING

 

WHEEL

STEERING BOOT

ADAPTER

 

TABS

TAB

 

 

SLOTS

EXTENSION SHAFT

 

LOWER STEERING SHAFT

 

 

03125

FIG. 1

INSTALL SEAT (See Figs. 2 and 3)

•Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Remove the cardboard packing and discard.

•Connect switch to seat.

•Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.

•Push down on seat to engage pads in slots and pull seat towards rear of tractor.

•Raise seat and tighten bolt securely.

•Remove tape and discard.

•Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat.

To adjust seat: Grasp adjustment handle and pull up, slide seat to desired position and release adjustment handle.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PB195H42LT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission RunningMaintenance Lubrication ChartBlade Removal See Fig BatteryTractor Important Special blade bolt is heat treatedEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig Service and Adjustments To Install Mower See FigTo Remove Mower See Fig Important Check Belt for Proper Routing ALL Mower Pulley GroovesCollar L onto guide and secure with retainer spring K To Level Mower To obtain the best cutting results, the mower blades shouldTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Alon THI Dotted Line REE LopeCanada contact Outdoor Products Customer Service DeptHOP Stevens Creek Road Terry Fox Way Augusta, GA 30907 USADept Service Customer Products Outdoor Canada Au AutoriséGarantie cette de exclus sont normal l’entretien et Degrés Dentretien Remarques Dépannage DE Guide Défectueux estRalenti DU Commande LA Régler Pour GAZ DES CommandeEntreposage DES L’AMPOULE Remplacer Pour Réglages ET RévisionFig la Voir Calandre LA ET Capot LE Enlever Pour Fig la Voir Batterie LA ReplacerCarrossage AVANT/ Roues DES Convergence TionrecdiLA DE L’ALIGNEMENT Régler Pour Tondeuse DE Lame DE Mentnetraî Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl PourFIG LA Voir ’EN Courroie LA Remplacer Pour22 .FIG Tondeuse LA Niveau LE Ajuster Pour24 .FIG 23 .FIG17 .FIG 20 .FIG 18 .FIG19 .FIG Place en bien est courroie la que vous-Assurez ImportantFig Voir Courroie LA ET Tondeuse LA InstallerReglages ET Revision Tondeuse LA Enlever PourFig La Voir Coupe DE Plateau DU Lavage DE Raccord Ligne EN Installé D’ESSENCE FiltreEntretien Fig la VoirMoteur DE D’HUILE Filtre ’ALLUMAGE BougieSilencieux AIR À FiltreFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETO I T a D N a M M O C E R Lubrification DE TableauUtilisation Chaque Avant Tonte DE Conseils UtilisationTransmission LA Purger 10 .FIG’ESSENCE Réservoir LE Remplir Accessoires AutresMoteur LE Démarrer Pour Moteur DU D’HUILE Niveau LE VérifierTracteur LE Transporter Pour Fig la Voir Tondeuse LA Utiliser PourMAR EN Fonctionnement DE Système Pentes LES Dans Utiliser PourFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Reculer Pour ET Avancer PourTracteur Votre Connaissez Propriété la de lendommagement Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier Pour mentnetionfonc tionsec la Voir Fig la Voir Batterie LA VérifierDesmancom Des fonction la et mentceplalem connaître Rouler Faisant LE EN Palette LA DE Tracteur LE Retirer PourEt 2 .Figs les Voir Siège LE Ajustez DU Tracteur LE Sortir PourPour Exigés Outils LES Tionrecdi DE Volant LE FixerMontar SIN Piezas Garantie U1R DimensionSommaire CCA .MIN AMP/HR’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils Avertissement

411287 specifications

The Poulan 411287 is a robust outdoor power tool designed to meet the needs of homeowners and landscaping professionals alike. This high-performance gas-powered chainsaw is especially popular for its reliability, versatility, and user-friendly features, making it an ideal choice for both cutting firewood and tackling larger landscaping tasks.

One of the standout features of the Poulan 411287 is its powerful engine. Equipped with a 40cc two-stroke engine, this chainsaw delivers impressive performance while ensuring efficient fuel consumption. The engine's design minimizes emissions, aligning with contemporary environmental standards and making it a more eco-friendly option in the chainsaw market.

The chainsaw also incorporates a 16-inch steel bar and chain, providing ample cutting capacity for various applications. This length strikes a perfect balance, allowing users to handle everything from small branches to medium-sized trees without compromising ease of use. The bar and chain design ensures smooth cutting action, reducing kickback and improving operator safety.

Ergonomics play a crucial role in the Poulan 411287's design. The chainsaw is equipped with a comfortable grip that minimizes vibrations, making it less taxing on the user's hands during extended use. Additionally, the lightweight construction enhances maneuverability, allowing users to work for longer periods without fatigue.

Another noteworthy feature is the automatic chain oiler, which ensures the chain is consistently lubricated during operation. This not only prolongs the life of the chainsaw but also enhances cutting efficiency. The tool-less chain tensioning system further simplifies maintenance, allowing users to quickly adjust the chain for optimal performance without the need for additional tools.

Furthermore, the Poulan 411287 is designed with a translucent fuel tank, enabling users to monitor fuel levels at a glance. This convenient feature helps prevent unexpected interruptions during tasks, ensuring productivity is maximized.

In conclusion, the Poulan 411287 is a well-rounded chainsaw that combines power, ease of use, and innovative features. Whether for the occasional homeowner or the dedicated landscaping professional, it provides a reliable solution for a wide range of cutting tasks. With its focus on efficiency and user comfort, the Poulan 411287 is undoubtedly a valuable addition to any outdoor toolkit.
Top Page Image Contents