Poulan 411287 manual Transaxle Motion Control Lever Neutral Adjustment See Fig

Page 23

SERVICE AND ADJUSTMENTS

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 27)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK

 

GATE

 

ADJUSTMENT

 

BOLT

FIG. 27

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 28

TO START ENGINE WITH A WEAK BATTERY (See Fig. 29)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 29

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model PB195H42LTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceIII. Children Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Using the Reverse Operation SystemReverse Operation System ROS To Operate Mower See FigADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelRunning Mowing TipsPurge Transmission Automatic Transmission Warm UPLubrication Chart MaintenanceImportant Special blade bolt is heat treated BatteryTractor Blade Removal See FigEngine Deck Washout Port See Fig CleaningIN-LINE Fuel Filter See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Collar L onto guide and secure with retainer spring K Important Check Belt for Proper RoutingALL Mower Pulley Grooves To obtain the best cutting results, the mower blades should To Level MowerTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Service Notes Fold Alon THI Dotted Line REE Lope Only Ride UP and Down Hill Not Across Hill Degrees MAXStevens Creek Road Terry Fox Way Augusta, GA 30907 USA Outdoor Products Customer Service DeptHOP Canada contactGarantie cette de exclus sont normal l’entretien et Dept Service Customer Products Outdoor Canada AuAutorisé Degrés Dentretien Remarques Défectueux est Dépannage DE GuideRalenti Entreposage DU Commande LA Régler PourGAZ DES Commande Fig la Voir Batterie LA Replacer Réglages ET RévisionFig la Voir Calandre LA ET Capot LE Enlever Pour DES L’AMPOULE Remplacer PourLA DE L’ALIGNEMENT Régler Pour Carrossage AVANT/ Roues DES ConvergenceTionrecdi ’EN Courroie LA Remplacer Pour Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl PourFIG LA Voir Tondeuse DE Lame DE Mentnetraî23 .FIG Tondeuse LA Niveau LE Ajuster Pour24 .FIG 22 .FIGPlace en bien est courroie la que vous-Assurez Important 20 .FIG 18 .FIG19 .FIG 17 .FIGTondeuse LA Enlever Pour Courroie LA ET Tondeuse LA InstallerReglages ET Revision Fig VoirFig la Voir Ligne EN Installé D’ESSENCE FiltreEntretien Fig La Voir Coupe DE Plateau DU Lavage DE RaccordAIR À Filtre ’ALLUMAGE BougieSilencieux Moteur DE D’HUILE FiltreEN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverUtilisation Chaque Avant O I T a D N a M M O C E RLubrification DE Tableau 10 .FIG UtilisationTransmission LA Purger Tonte DE ConseilsMoteur DU D’HUILE Niveau LE Vérifier Accessoires AutresMoteur LE Démarrer Pour ’ESSENCE Réservoir LE RemplirPentes LES Dans Utiliser Pour Fig la Voir Tondeuse LA Utiliser PourMAR EN Fonctionnement DE Système Tracteur LE Transporter PourReculer Pour ET Avancer Pour GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Fig la Voir Mentne -TIONSTA DE Frein LE Engager PourTracteur Votre Connaissez Propriété la de lendommagement Toutes SI Vérifier Toutes SI Vérifier MontageCorrectement Sont Courroies LES Rouler Faisant LE EN Palette LA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA VérifierDesmancom Des fonction la et mentceplalem connaître Pour mentnetionfonc tionsec la VoirTionrecdi DE Volant LE Fixer DU Tracteur LE Sortir PourPour Exigés Outils LES Et 2 .Figs les Voir Siège LE AjustezMontar SIN Piezas CCA .MIN AMP/HR U1R DimensionSommaire Garantie’ESSENCE DE Sûre Manipulation Général EntretienTracteurs des sécurité toute ’utilisation pour ConseilsTracteurs des sécurité toute en l’utilisation pour Conseils PentesLES Dans Fonctionnement Avertissement

411287 specifications

The Poulan 411287 is a robust outdoor power tool designed to meet the needs of homeowners and landscaping professionals alike. This high-performance gas-powered chainsaw is especially popular for its reliability, versatility, and user-friendly features, making it an ideal choice for both cutting firewood and tackling larger landscaping tasks.

One of the standout features of the Poulan 411287 is its powerful engine. Equipped with a 40cc two-stroke engine, this chainsaw delivers impressive performance while ensuring efficient fuel consumption. The engine's design minimizes emissions, aligning with contemporary environmental standards and making it a more eco-friendly option in the chainsaw market.

The chainsaw also incorporates a 16-inch steel bar and chain, providing ample cutting capacity for various applications. This length strikes a perfect balance, allowing users to handle everything from small branches to medium-sized trees without compromising ease of use. The bar and chain design ensures smooth cutting action, reducing kickback and improving operator safety.

Ergonomics play a crucial role in the Poulan 411287's design. The chainsaw is equipped with a comfortable grip that minimizes vibrations, making it less taxing on the user's hands during extended use. Additionally, the lightweight construction enhances maneuverability, allowing users to work for longer periods without fatigue.

Another noteworthy feature is the automatic chain oiler, which ensures the chain is consistently lubricated during operation. This not only prolongs the life of the chainsaw but also enhances cutting efficiency. The tool-less chain tensioning system further simplifies maintenance, allowing users to quickly adjust the chain for optimal performance without the need for additional tools.

Furthermore, the Poulan 411287 is designed with a translucent fuel tank, enabling users to monitor fuel levels at a glance. This convenient feature helps prevent unexpected interruptions during tasks, ensuring productivity is maximized.

In conclusion, the Poulan 411287 is a well-rounded chainsaw that combines power, ease of use, and innovative features. Whether for the occasional homeowner or the dedicated landscaping professional, it provides a reliable solution for a wide range of cutting tasks. With its focus on efficiency and user comfort, the Poulan 411287 is undoubtedly a valuable addition to any outdoor toolkit.
Top Page Image Contents