Poulan 425858 manual To USE Cruise Control -J See Fig, To Adjust Mower Cutting Height See Fig

Page 13

OPERATION

J

K

L

FIG. 17

TO USE CRUISE CONTROL -J (See Fig. 17)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trim- mimg or turning.

With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 18)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 18

Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being

mowed.13

The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and bet- ter looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 19)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in this section of manual).

With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

Repeat for all, installing gauge wheel in same ad- justment hole.

FIG.19

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES -

disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place.

Image 13
Contents 425858 12-01-08 BAD ModelGeneral Operation Safe Operation Practices for Ride-On MowersII. Slope Operation General Service ServiceIII. Children IV. TowingTable of Contents Unpack Carton To Remove Tractor from CartonInstall Mower and Drive Belt Adjust Seat See FigRoll tractor forward off skid Attach Mower Side Suspension Arms a First Install ANTI-SWAY BAR SEH J Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo USE Cruise Control -J See Fig To Operate MowerReverse Operation System ROS Service REMINDER/HOUR MeterTo Transport See Figs To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Tractor BatteryBrake Operation Blade CareBelts EngineTransaxle Cooling Transaxle Pump FluidCleaning To Remove Mower See Fig To Install MowerTo Level Mower To lower mower Turn nut right Turn nut left To raise mowerTo Check Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbFuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsMower blades will not HOP Limited WarrantyService Notes Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Dentretien Notes Limitée Garantie Correction Cause Problème Dépannage DE GuideLa réduisez ou haute plus coupe de position en Mettez Entreposage Carburateur LE Régler Pour Reglages ET RevisionFig la Voir Batterie LA Replacer Roue LA DE PINCEMENT/CARROSSAGE AvantLA DE Lame LA DE D’ENTRAÎNEMENT FIG LA Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl PourCourroie Acer Rempl Pour Freins LES Vérifier PourAVANT/ARRIÈRE Ajustement Fig la Voir Tondeuse LA Installer PourTondeuse LA Niveau LE Ajuster Pour Tondeuse LA Enlever PourFig La Voir Coupe DE Plateau DU Lavage DE Raccord Entretien’ALLUMAGE Bougie AIR À FiltreSionmistrans LA DE Moteur Fluide LubrificationTransmission LA DE Refroidissement Trapézoïdales CourroiesLames DES Entretien Fig la Voir Lame LA EnleverEN Fonctionnement DE Système ET Lubrification DE Tableau Généra Recommandations LESUtilisation Chaque Avant Transmission LA Purger Utilisation22 .FIG ’ESSENCE Réservoir LE Remplir Moteur LE Démarrer PourMoteur DU D’HUILE Niveau LE Vérifier Quetima’ENTRETIEN/HOROMÈTRE Indicateur Accessoires Autres ET Charrettes DES Remorquer Pour21 et 13 .Fig les Voir Pentes LES Dans Utiliser PourTondeuse LA Utiliser Pour Fig la Voir J- Vitess DE Régulateur LE Utiliser CommentJauge DE Roues LES Régler Pour Système DU CaractéristiquesFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourReculer Pour ET Avancer Pour Létrangleur Utiliser Pour13 .FIG ’EMBRAYAGE NI DE EST Tondeuse LA SI Vérifier Montage10 .FIG 12 .FIG 11 .FIGLA DE Latéraux Suspension DE Bras LES Fixez ROULIS-ANTI Barre LA D’ABORD InstallezPAL LA DE Tracteur LE Retirer Pour PA LA DE Tracteur LE Retirer PourToncar DU Tracteur LE Sortir Pour Montées NON PiécesFig la Voir Batterie LA Vérifier Clés Pente-GuideGarantie ’ENTRETIEN Guide SommaireUtilisation Réglages ET Révision Produit DE SpécificationsTracteurs des sécurité toute Général EntretienEn l’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationTracteurs des sécurité toute en l’utilisation pour Conseils TESBAD 08-01-12 AUX ImpriméAvertissement

425858, 9604200602 specifications

The Poulan 425858, 9604200602 model is a powerful and versatile tool designed for outdoor enthusiasts and professionals alike. This chainsaw is part of Poulan's commitment to delivering performance and reliability in lawn and garden equipment. Known for its user-friendly features and robust construction, the Poulan 425858 is an excellent choice for cutting firewood, tree trimming, and various landscaping tasks.

One of the standout features of the Poulan 425858 is its powerful engine. Equipped with a high-performance 42cc gas engine, this chainsaw is capable of handling tough cutting tasks with ease. The engine provides ample power while maintaining fuel efficiency, allowing users to work longer without frequent refueling. The chainsaw's automatic oiling system also ensures that the bar and chain remain lubricated during operation, extending the tool's lifespan and performance.

The design of the Poulan 425858 prioritizes user comfort and safety. Its ergonomic handle and lightweight construction make it easy to maneuver, reducing user fatigue during extended use. The chainsaw is also fitted with a low-vibration technology that minimizes vibration levels, enhancing comfort further while reducing the risk of fatigue and discomfort in the hands and arms.

Safety features are paramount in the design of the Poulan 425858. The chainsaw includes a chain brake that automatically stops the chain in case of kickback, providing peace of mind to the user. Additionally, the tool’s safety throttle lock prevents accidental starting, ensuring that the chainsaw only operates when the user is ready.

Adjustment and maintenance are made simple with this model. The Poulan 425858 features a tool-less chain tensioning system, allowing users to quickly and easily adjust the chain tension without the need for additional tools. This feature ensures optimal performance and safety, as a properly tensioned chain reduces the likelihood of accidents.

In summary, the Poulan 425858, 9604200602 model is a reliable and efficient chainsaw that combines power, safety, and ease of use. With its efficient engine, user-friendly design, and proactive safety features, it is well-suited for both casual users and professionals. Whether you're tackling tough jobs around the yard or maintaining trees on a larger property, the Poulan 425858 is a dependable tool that delivers on performance and convenience.