Poulan 425858 To Replace Mower Blade Drive Belt, To Check Brake, To Replace Motion Drive Belt

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 33)

•Park tractor on a level surface. Engage parking brake.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod (K) from lock bracket

(L).

CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and release slowly.

•Remove screws (P) from mandrel covers (Q) and remove covers.

•Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

•Remove belt from electric clutch pulley (M), both mandrel pulleys (R) and all idler pulleys (S).

MOWER DRIVE BELT INSTALLATION

•Install belt around all mandrel pulleys (R) and around idler pulleys (S) as shown.

•Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Reassemble mandrel covers (Q). Securely tighten all screws.

•Engage belt tension rod (K) on locking bracket

(L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Raise attachment lift lever to highest position.

P

Q

L

KR

R

S

R

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved sur- face, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel con- trol in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT

(See Fig. 34)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Disconnect clutch wire harness (A).

•Remove anti-rotation link (B) on right side of trac- tor.

•Remove belt from stationary idler (C) and clutching idler (D).

•Remove belt from centerspan idler (E).

•Pull belt slack toward rear of tractor. Carefully re- move belt upwards from transmission input pulley and over cooling fan blades (F).

•Remove belt downward from engine pulley and around electric clutch (G).

•Slide belt toward rear of tractor, off the steering plate (H) and remove from tractor.

M

P

Q

FIG. 33

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 425858 12-01-08 BAD ModelII. Slope Operation Safe Operation Practices for Ride-On MowersGeneral Operation IV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unpack Carton To Remove Tractor from CartonRoll tractor forward off skid Adjust Seat See FigInstall Mower and Drive Belt Attach Mower Side Suspension Arms a First Install ANTI-SWAY BAR SEH J Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control -J See FigTo Operate on Hills Service REMINDER/HOUR MeterReverse Operation System ROS To Transport See FigsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Blade Care BatteryTractor Brake OperationTransaxle Pump Fluid EngineBelts Transaxle CoolingCleaning To Level Mower To Install MowerTo Remove Mower See Fig To lower mower Turn nut right Turn nut left To raise mowerTo Replace Motion Drive Belt To Replace Mower Blade Drive BeltTo Check Brake To Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsMower blades will not HOP Limited WarrantyService Notes Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Dentretien Notes Limitée Garantie Correction Cause Problème Dépannage DE GuideLa réduisez ou haute plus coupe de position en Mettez Entreposage Fig la Voir Batterie LA Replacer Reglages ET RevisionCarburateur LE Régler Pour Roue LA DE PINCEMENT/CARROSSAGE AvantFreins LES Vérifier Pour FIG LA Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl PourLA DE Lame LA DE D’ENTRAÎNEMENT Courroie Acer Rempl PourAVANT/ARRIÈRE Ajustement Tondeuse LA Enlever Pour Tondeuse LA Installer PourFig la Voir Tondeuse LA Niveau LE Ajuster PourAIR À Filtre EntretienFig La Voir Coupe DE Plateau DU Lavage DE Raccord ’ALLUMAGE BougieTrapézoïdales Courroies LubrificationSionmistrans LA DE Moteur Fluide Transmission LA DE RefroidissementEN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverLames DES Entretien Utilisation Chaque Avant Généra Recommandations LESLubrification DE Tableau 22 .FIG UtilisationTransmission LA Purger Quetima Moteur LE Démarrer Pour’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE VérifierPentes LES Dans Utiliser Pour Accessoires Autres ET Charrettes DES Remorquer Pour’ENTRETIEN/HOROMÈTRE Indicateur 21 et 13 .Fig les VoirSystème DU Caractéristiques Fig la Voir J- Vitess DE Régulateur LE Utiliser CommentTondeuse LA Utiliser Pour Jauge DE Roues LES Régler PourLétrangleur Utiliser Pour GAZ DES Commande LA Utiliser PourFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour Reculer Pour ET Avancer Pour13 .FIG ’EMBRAYAGE NI DE EST Tondeuse LA SI Vérifier Montage10 .FIG 12 .FIG 11 .FIGLA DE Latéraux Suspension DE Bras LES Fixez ROULIS-ANTI Barre LA D’ABORD InstallezPAL LA DE Tracteur LE Retirer Pour PA LA DE Tracteur LE Retirer PourClés Pente-Guide Montées NON PiécesToncar DU Tracteur LE Sortir Pour Fig la Voir Batterie LA VérifierRéglages ET Révision Produit DE Spécifications SommaireGarantie ’ENTRETIEN Guide Utilisation’ESSENCE DE Sûre Manipulation Général EntretienTracteurs des sécurité toute En l’utilisation pour ConseilsTracteurs des sécurité toute en l’utilisation pour Conseils TESAvertissement AUX ImpriméBAD 08-01-12

425858, 9604200602 specifications

The Poulan 425858, 9604200602 model is a powerful and versatile tool designed for outdoor enthusiasts and professionals alike. This chainsaw is part of Poulan's commitment to delivering performance and reliability in lawn and garden equipment. Known for its user-friendly features and robust construction, the Poulan 425858 is an excellent choice for cutting firewood, tree trimming, and various landscaping tasks.

One of the standout features of the Poulan 425858 is its powerful engine. Equipped with a high-performance 42cc gas engine, this chainsaw is capable of handling tough cutting tasks with ease. The engine provides ample power while maintaining fuel efficiency, allowing users to work longer without frequent refueling. The chainsaw's automatic oiling system also ensures that the bar and chain remain lubricated during operation, extending the tool's lifespan and performance.

The design of the Poulan 425858 prioritizes user comfort and safety. Its ergonomic handle and lightweight construction make it easy to maneuver, reducing user fatigue during extended use. The chainsaw is also fitted with a low-vibration technology that minimizes vibration levels, enhancing comfort further while reducing the risk of fatigue and discomfort in the hands and arms.

Safety features are paramount in the design of the Poulan 425858. The chainsaw includes a chain brake that automatically stops the chain in case of kickback, providing peace of mind to the user. Additionally, the tool’s safety throttle lock prevents accidental starting, ensuring that the chainsaw only operates when the user is ready.

Adjustment and maintenance are made simple with this model. The Poulan 425858 features a tool-less chain tensioning system, allowing users to quickly and easily adjust the chain tension without the need for additional tools. This feature ensures optimal performance and safety, as a properly tensioned chain reduces the likelihood of accidents.

In summary, the Poulan 425858, 9604200602 model is a reliable and efficient chainsaw that combines power, safety, and ease of use. With its efficient engine, user-friendly design, and proactive safety features, it is well-suited for both casual users and professionals. Whether you're tackling tough jobs around the yard or maintaining trees on a larger property, the Poulan 425858 is a dependable tool that delivers on performance and convenience.
Top Page Image Contents