Poulan 9604200602, 425858 manual Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs See Fig

Page 24

SERVICE AND ADJUSTMENTS

BELT INSTALLATION -

•Install new belt from tractor rear to front, over the steering plate (H) and above clutch brake pedal shaft (J).

•Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

•Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (F). Be sure belt is inside the belt keeper.

•Install belt on centerspan idler (E).

•Install belt through stationary idler (C) and clutch- ing idler (D).

•Reinstall anti-rotation link (B) on right side of trac- tor. Tighten securely.

•Reconnect clutch harness (A).

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

 

G

 

H

B

A

 

 

C

 

J

 

D

 

E

 

F

 

02953

 

electric

FIG. 34

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 35)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 35

TO START ENGINE WITH A WEAK BATTERY (See Fig. 36)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+) terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGA- TIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and

24battery.

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model 425858 12-01-08 BADSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service General ServiceIII. Children IV. TowingTable of Contents To Remove Tractor from Carton Unpack CartonAdjust Seat See Fig Install Mower and Drive BeltRoll tractor forward off skid First Install ANTI-SWAY BAR S Attach Mower Side Suspension Arms aEH J Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo USE Cruise Control -J See Fig To Operate MowerService REMINDER/HOUR Meter Reverse Operation System ROSTo Transport See Figs To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionLubrication Chart General RecommendationsBefore Each USE Battery TractorBrake Operation Blade CareEngine BeltsTransaxle Cooling Transaxle Pump FluidCleaning To Install Mower To Remove Mower See FigTo Level Mower Turn nut right Turn nut left To raise mower To lower mowerTo Replace Mower Blade Drive Belt To Check BrakeTo Replace Motion Drive Belt To Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbOther Fuel SystemEngine OIL CylindersTroubleshooting Points Problem Cause CorrectionMower blades will not Limited Warranty HOPService Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Dentretien Notes Limitée Garantie Dépannage DE Guide Correction Cause ProblèmeLa réduisez ou haute plus coupe de position en Mettez Entreposage Reglages ET Revision Carburateur LE Régler PourFig la Voir Batterie LA Replacer Avant Roue LA DE PINCEMENT/CARROSSAGEFIG LA Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour LA DE Lame LA DE D’ENTRAÎNEMENTCourroie Acer Rempl Pour Freins LES Vérifier PourAVANT/ARRIÈRE Ajustement Tondeuse LA Installer Pour Fig la VoirTondeuse LA Niveau LE Ajuster Pour Tondeuse LA Enlever PourEntretien Fig La Voir Coupe DE Plateau DU Lavage DE Raccord’ALLUMAGE Bougie AIR À FiltreLubrification Sionmistrans LA DE Moteur FluideTransmission LA DE Refroidissement Trapézoïdales CourroiesFig la Voir Lame LA Enlever Lames DES EntretienEN Fonctionnement DE Système ET Généra Recommandations LES Lubrification DE TableauUtilisation Chaque Avant Utilisation Transmission LA Purger22 .FIG Moteur LE Démarrer Pour ’ESSENCE Réservoir LE RemplirMoteur DU D’HUILE Niveau LE Vérifier QuetimaAccessoires Autres ET Charrettes DES Remorquer Pour ’ENTRETIEN/HOROMÈTRE Indicateur21 et 13 .Fig les Voir Pentes LES Dans Utiliser PourFig la Voir J- Vitess DE Régulateur LE Utiliser Comment Tondeuse LA Utiliser PourJauge DE Roues LES Régler Pour Système DU CaractéristiquesGAZ DES Commande LA Utiliser Pour Fig la Voir Mentne -TIONSTA DE Frein LE Engager PourReculer Pour ET Avancer Pour Létrangleur Utiliser Pour13 .FIG ’EMBRAYAGE Montage NI DE EST Tondeuse LA SI Vérifier12 .FIG 11 .FIG 10 .FIGROULIS-ANTI Barre LA D’ABORD Installez LA DE Latéraux Suspension DE Bras LES FixezPA LA DE Tracteur LE Retirer Pour PAL LA DE Tracteur LE Retirer PourMontées NON Piéces Toncar DU Tracteur LE Sortir PourFig la Voir Batterie LA Vérifier Clés Pente-GuideSommaire Garantie ’ENTRETIEN GuideUtilisation Réglages ET Révision Produit DE SpécificationsGénéral Entretien Tracteurs des sécurité touteEn l’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationTES Tracteurs des sécurité toute en l’utilisation pour ConseilsAUX Imprimé BAD 08-01-12Avertissement

425858, 9604200602 specifications

The Poulan 425858, 9604200602 model is a powerful and versatile tool designed for outdoor enthusiasts and professionals alike. This chainsaw is part of Poulan's commitment to delivering performance and reliability in lawn and garden equipment. Known for its user-friendly features and robust construction, the Poulan 425858 is an excellent choice for cutting firewood, tree trimming, and various landscaping tasks.

One of the standout features of the Poulan 425858 is its powerful engine. Equipped with a high-performance 42cc gas engine, this chainsaw is capable of handling tough cutting tasks with ease. The engine provides ample power while maintaining fuel efficiency, allowing users to work longer without frequent refueling. The chainsaw's automatic oiling system also ensures that the bar and chain remain lubricated during operation, extending the tool's lifespan and performance.

The design of the Poulan 425858 prioritizes user comfort and safety. Its ergonomic handle and lightweight construction make it easy to maneuver, reducing user fatigue during extended use. The chainsaw is also fitted with a low-vibration technology that minimizes vibration levels, enhancing comfort further while reducing the risk of fatigue and discomfort in the hands and arms.

Safety features are paramount in the design of the Poulan 425858. The chainsaw includes a chain brake that automatically stops the chain in case of kickback, providing peace of mind to the user. Additionally, the tool’s safety throttle lock prevents accidental starting, ensuring that the chainsaw only operates when the user is ready.

Adjustment and maintenance are made simple with this model. The Poulan 425858 features a tool-less chain tensioning system, allowing users to quickly and easily adjust the chain tension without the need for additional tools. This feature ensures optimal performance and safety, as a properly tensioned chain reduces the likelihood of accidents.

In summary, the Poulan 425858, 9604200602 model is a reliable and efficient chainsaw that combines power, safety, and ease of use. With its efficient engine, user-friendly design, and proactive safety features, it is well-suited for both casual users and professionals. Whether you're tackling tough jobs around the yard or maintaining trees on a larger property, the Poulan 425858 is a dependable tool that delivers on performance and convenience.
Top Page Image Contents