Poulan 960 61 01-57 To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation

Page 23

SERVICE AND ADJUSTMENTS

BOTTOM EDGE

00598

BOTTOM EDGE

OF MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

Fig. 25

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

SUSPENSION ARM

01553

LIFT LINK ADJUSTMENT NUT

Fig. 26

FRONT-TO-BACK ADJUSTMENT (See Figs. 27 and 28)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

01268

MANDREL

"D""D"

Fig. 27

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

01267

NUT "E"

NUT "F"

TRUNNION

FRONT LINKS

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 29)

Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Remove screws from RH mandrel cover and remove cover.

•Remove screws from LH mandrel cover and remove cover.

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal. See belt routing decal located on right mandrel cover.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install left and right mandrel covers and tighten securely. Make sure belt is in mandrel pulley cover.

•Install mower (see "To install mower" in this section of this manual).

 

LH MANDREL COVER

 

RH MANDREL

 

COVER

MANDREL

BELT

 

PULLEY

 

 

MANDREL

 

PULLEY

IDLER

 

PULLEY

IDLER PULLEY

 

Fig. 29

Fig. 28

23

 

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PP16H36RB II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceIII. Children Table of Contents +EY Unassembled Parts3EAT AtteryBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig To Assemble Bagger See Figs A-5C To Install Bagger Components to Tractor See Figs A-4DTo Assemble and Install Mulcher Plug See Fig Bagger Adjustment SeeHorizontal Adjustment Vertical AdjustmentCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSADD Gasoline Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelNing Mowing TipsPurge Transmission Mulching Mowing TipsBagging see Fig To Dump Bagger SeeTo Convert Mower See Fig Lubrication Chart MaintenanceCheck Operator Presence System TractorStar Pattern Blade See Fig Blade Care See FigEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Adjust Throttle Control Cable To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch Schematic Repair PartsElectrical 532 17 KEY Part DescriptionChassis and Enclosures 532 42 532 40Drive 817 49 Steering Assembly 532 19 Steering Wheel Seat Assembly Wheels & Tires DecalsEngine Tank Fuel Mower 532 19 532 17 Link Front Mower Lift532 41 Bagger532 16 52-49 Tube Handle Bagger CRD Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

960 61 01-57, 96061015703, PP16H36RB specifications

The Poulan PP16H36RB, model number 96061015703, is a robust and versatile lawn mower designed to tackle various landscape maintenance tasks with ease. It embodies a powerful combination of features and technologies that cater to both novice and experienced users, making lawn care an enjoyable and efficient chore.

At the heart of the Poulan PP16H36RB is a reliable 16 horsepower Briggs & Stratton engine, ensuring ample power to navigate tough terrain and handle thick grass effortlessly. The engine is designed for efficiency and longevity, providing smooth operation and requiring minimal maintenance. This engine is paired with a user-friendly electric start feature, allowing for quick and hassle-free ignition.

One of the standout features of this model is its wide cutting deck, which measures 36 inches. This generous width enables the mower to cover more ground in a single pass, significantly reducing mowing time. The cutting deck is equipped with durable, sharp blades that provide a clean, precise cut, promoting a healthy lawn. The mower also offers multiple cutting height adjustments, ranging from 1.5 to 4 inches, allowing users to customize their mowing to suit different grass types and personal preferences.

The Poulan PP16H36RB is designed for comfort and control, featuring an ergonomic, fully adjustable seat that supports the user during long mowing sessions. The mower is equipped with a smooth hydrostatic transmission that allows for seamless speed control. This feature enhances maneuverability around obstacles such as trees and flowerbeds, ensuring that users can maintain their lawns without missing a spot.

Safety is also a priority in the design of the PP16H36RB. The mower includes essential safety features such as automatic blade disengagement, which stops the blades when the user leaves the seat, preventing accidents. The sturdy frame and reliable construction ensure that users can navigate rough terrain without compromising stability or safety.

In conclusion, the Poulan PP16H36RB, with its powerful engine, wide cutting deck, and user-friendly features, stands out as a dependable choice for anyone looking to maintain their yard effortlessly. It combines comfort, efficiency, and safety, making it an excellent investment for achieving a beautifully manicured lawn. With the Poulan PP16H36RB, lawn care becomes less of a chore and more of a pleasure.
Top Page Image Contents