Poulan PD25PH48STB owner manual Tractor

Page 17

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position.

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 13)

Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

Remove blade bolt by turning counterclockwise.

Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

BLADE

MANDREL

ASSEMBLY

 

CENTER

HOLE

BLADE BOLT (SPECIAL)

STAR

FIG. 13

TO SHARPEN BLADE (See Fig. 14)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

BLADE

5/8" BOLT OR PIN

FIG. 14

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

17

Image 17
Contents PD25PH48STB Safety Rules Safety Rules Table of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP NingLubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Clean AIR INTAKE/COOLING Areas CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary To Replace Mower Drive BeltTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransmission REMOVAL/REPLACEMENT To Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust CarburetorInterlocks and Relays To Replace FuseOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Tractor Model Number PD25PH48STB SchematicElectrical 188031 KEY Part DescriptionChassis and Enclosures 186689 187495Drive Tractor Model Number PD25PH48STB17000612 17060516Steering Assembly 188967 184704X428 Wheel Steering 184706 Axle72110618 Spark Arrester EngineOptional Equipment KEY Part NO. NO. Description Seat Seat Assembly1712 Wheels & Tires DecalsMower Lift 124526X 178981125631X Mower Deck KEY Part Description Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

PD25PH48STB specifications

The Poulan PD25PH48STB is a versatile lawn tractor designed to deliver performance and comfort for homeowners looking to maintain their lawns with ease. It is particularly well-suited for those with medium to large yards, providing the necessary power and features to make lawn care more efficient.

One of the standout features of the Poulan PD25PH48STB is its robust 48-inch cutting deck, which allows for a wider cutting path. This is beneficial for covering more ground in less time, reducing the overall time spent mowing the lawn. The deck is designed with a durable steel construction that ensures longevity and resilience against various elements.

The mower is powered by a reliable 25 horsepower Briggs & Stratton engine. This engine combines power with fuel efficiency, offering excellent performance to tackle even the toughest grass conditions. The electric start feature adds convenience, allowing users to start the engine with the turn of a key rather than the traditional method of pulling a cord.

Another notable characteristic of the PD25PH48STB is its six-speed transmission, which provides excellent control and adaptability depending on the mowing conditions. This allows users to adjust their speed based on their preference or the terrain, whether it’s flat or hilly.

The tractor also features an ergonomic seat design, ensuring comfort during extended mowing sessions. The adjustable seat makes it easy to find the perfect riding position, while the easy-to-reach controls enhance the overall user experience. To further enhance comfort, the PD25PH48STB comes equipped with a deck wash port that simplifies cleaning, allowing users to maintain the mower with minimal effort.

For those concerned about safety, this lawn tractor includes an automatic safety shut-off feature that engages when the operator leaves the seat, providing peace of mind while mowing. Additionally, the tight turning radius allows for greater maneuverability, making it easier to navigate around trees, flower beds, and other obstacles in the yard.

Overall, the Poulan PD25PH48STB is an exceptional choice for homeowners looking for a dependable, efficient, and comfortable lawn mowing solution. With its powerful engine, generous cutting deck, user-friendly features, and safety mechanisms, it stands out as a top contender in the lawn tractor market.