Poulan PD25PH48STB owner manual Install Seat See Fig, Assemble Gauge Wheels to Mower Deck See Fig

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

 

ADJUSTMENT

 

KNOB

02464

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4)

The gauge wheels are designed to keep the mower deck in properpositionwhenoperatingmower.Besuretheyareproperly adjusted to ensure optimum mower performance.

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

•For ease of mower to tractor assembly, raise gauge wheels to highest position and retain with clevis pins and spring retainers.

•Adjust gauge wheels before operating mower. See “TO ADJUST GAUGE WHEELS” in the Operation section of this manual.

RETAINER SPRING

PIN

ADJUSTING

SHOULDER BAR

BOLT

GAUGE

WHEEL 3/8-16 CENTER LOCKNUT

3/8 WASHER

FIG. 4

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PD25PH48STB Safety Rules Safety Rules Table of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Brake System Check Tire PressureCheck Mower Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelNing Purge TransmissionMowing Tips Automatic Transmission Warm UPBefore Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine Spark Plugs CleaningClean AIR INTAKE/COOLING Areas MufflerTo Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary To Replace Mower Drive BeltTransmission REMOVAL/REPLACEMENT To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWith attachment clutch Tractor Model Number PD25PH48STB SchematicElectrical 188031 KEY Part DescriptionChassis and Enclosures 186689 187495Drive Tractor Model Number PD25PH48STB17000612 17060516Steering Assembly 72110618 184704X428 Wheel Steering 184706 Axle188967 Optional Equipment EngineSpark Arrester KEY Part NO. NO. Description 1712 Seat AssemblySeat Wheels & Tires DecalsMower Lift 125631X 178981124526X Mower Deck KEY Part Description Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

PD25PH48STB specifications

The Poulan PD25PH48STB is a versatile lawn tractor designed to deliver performance and comfort for homeowners looking to maintain their lawns with ease. It is particularly well-suited for those with medium to large yards, providing the necessary power and features to make lawn care more efficient.

One of the standout features of the Poulan PD25PH48STB is its robust 48-inch cutting deck, which allows for a wider cutting path. This is beneficial for covering more ground in less time, reducing the overall time spent mowing the lawn. The deck is designed with a durable steel construction that ensures longevity and resilience against various elements.

The mower is powered by a reliable 25 horsepower Briggs & Stratton engine. This engine combines power with fuel efficiency, offering excellent performance to tackle even the toughest grass conditions. The electric start feature adds convenience, allowing users to start the engine with the turn of a key rather than the traditional method of pulling a cord.

Another notable characteristic of the PD25PH48STB is its six-speed transmission, which provides excellent control and adaptability depending on the mowing conditions. This allows users to adjust their speed based on their preference or the terrain, whether it’s flat or hilly.

The tractor also features an ergonomic seat design, ensuring comfort during extended mowing sessions. The adjustable seat makes it easy to find the perfect riding position, while the easy-to-reach controls enhance the overall user experience. To further enhance comfort, the PD25PH48STB comes equipped with a deck wash port that simplifies cleaning, allowing users to maintain the mower with minimal effort.

For those concerned about safety, this lawn tractor includes an automatic safety shut-off feature that engages when the operator leaves the seat, providing peace of mind while mowing. Additionally, the tight turning radius allows for greater maneuverability, making it easier to navigate around trees, flower beds, and other obstacles in the yard.

Overall, the Poulan PD25PH48STB is an exceptional choice for homeowners looking for a dependable, efficient, and comfortable lawn mowing solution. With its powerful engine, generous cutting deck, user-friendly features, and safety mechanisms, it stands out as a top contender in the lawn tractor market.
Top Page Image Contents