Poulan 96042003505 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Figs

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

Depress clutch/brake pedal fully and set parking brake.

Place gearshift lever in neutral (N) position.

Place attachment clutch in “DISENGAGED” position.

Turn ignition key to “STOP” and remove key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 21)

Place attachment clutch in “DISENGAGED” position.

Lower attachment lift lever to its lowest position.

Remove mower belt from engine pulley (M).

Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket.

Remove clutch cable spring (Q) from idler arm (R).

Disconnect front link (E) from mower - remove retainer spring and washer.

Go to either side of mower and disconnect mower suspension arm (A) from chassis and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

Go to other side of mower and disconnect the suspen- sion arm and rear lift link.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINK (E) AND REAR LIFT LIKS

(C)FROM TRACTOR AND HOOK THE CLUTCH SPRING

(Q)INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH.

TO INSTALL MOWER (See Figs. 21-26)

Be sure tractor is on level surface and engage parking brake.

Lower attachment lift lever to it's lowest position.

CAUTION: Lift lever is spring loaded. Have a tight grip on lift lever, lower it slowly and engage in lowest position.

CAUTION: After rear lift links are dis- connected, the attachment lift lever will be spring loaded. Have a tight grip on lift lever when changing position of the lever.

• Slide mower out from under right side of tractor.

B

 

Q R

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

Slide mower under tractor until it is centered under tractor.

MF

AE

P

K

C

D

L

19

FIG. 21

 

 

 

Image 19
Contents Model PB19546LTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIII. Children ServiceIV. Towing Table of Contents Key Slope Sheet Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Install Seat See FigsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigsTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigReverse Operation System ROS See Fig Before Starting the Engine To Start Engine See Fig Mowing TipsLubrication Chart MaintenanceCheck Operator Presence System BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M To Level Mower To Replace Motion Belt Drive See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Attach Jumper Cables To Adjust Steering Wheel AlignmentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Service Notes Fold Alon THI Dotted Line REE Lope Only Ride UP and Down Hill Not Across Hill Degrees MAXPage Page Degrés ’ENTRETIEN Remarques Défectueux est Dépannage DE GuideRalenti Entreposage Carburateur LE Régler Pour Starter DU Commande LA Régler PourGAZ DES Commande Réglages ET RévisionChargée Mentretièen Batterie Déchargée OU Faible Batterie Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourCarrossage AVANT/ Roues DES Convergence Tionrecdi LA DE L’ALIGNEMENT Régler PourTondeuse DE Lame DE Mentnetraî 33 .FigFIG LA Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour FIG LA Voir28 .FIG Tondeuse LA Niveau LE Ajuster Pour30 .FIG 29 .FIG23 .FIG 26 .FIG25 .FIG 24 .FIGFig Voir Cour LA ET Tondeuse LA InstallerReglages ET Revision Figs Voir D’ENTRAÎNEMENT RoieNettoyage Ligne EN Installé D’ESSENCE FiltreEntretien Fig la VoirMoteur Frein DU Fonctionnement Fig la Voir Lame LA EnleverLames DES Entretien PneusLubrification DE Tableau O I T a D N a M M O C E RUtilisation Chaque Avant 14 .FIG UtilisationTonte DE Conseils Moteur LE Démarrer PourET Charrettes DES Remorquer Pour Accessoires Autres’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE Vérifier10 .FIG Jauge DE Roues LES Régler Pour12 .FIG 11 .FIGTionsta DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourEt 7 .Figs la Voir Arrêter Pour Fig la Voir MentneDattachement Propriété la de lendommagement Correctement Sont Courroies LES MontageToutes SI Vérifier Toutes SI Vérifier Et 2 .Figs les Voir Siège LE Ajustez Fig la Voir Batterie LA VérifierCarton LE Deballer DU Tracteur LE Sortir PourPour Exigés Outils LES Tionrecdi DE Volant LE FixerMontar SIN Piezas 27-26 Dépannage DE Guide Sommaire24-19 Réglages ET Révision ’ESSENCE DE Sûre Manipulation Général EntretienTracteurs des sécurité toute ’utilisation pour ConseilsLES Dans Fonctionnement PentesTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

96042003505 specifications

The Poulan 96042003505 is a high-performance chainsaw designed to meet the dynamic needs of both casual users and professional arborists. This robust tool is known for its reliability, efficiency, and ease of use, making it a popular choice among various outdoor maintenance enthusiasts.

One of the standout features of the Poulan 96042003505 is its powerful 42cc engine. This Two-Stroke engine delivers impressive cutting performance, allowing users to easily tackle a range of tasks from pruning trees to cutting firewood. The design emphasizes fuel efficiency and reduced emissions, aligning with modern environmental standards without compromising power.

Another key characteristic of the Poulan 96042003505 is its lightweight construction. Weighing in at approximately 12 pounds, it provides excellent maneuverability without sacrificing durability. The lightweight design means that users can operate the chainsaw for extended periods with reduced fatigue, making it ideal for large projects.

This chainsaw is equipped with a 16-inch bar, providing an optimal balance between cutting ability and control. The bar length allows users to cut through medium-sized trees and thick branches with ease, making it versatile for both residential and professional use.

Technologically, the Poulan 96042003505 features an automatic oiler system, ensuring a steady supply of lubrication to the chain. This system promotes longer chainsaw life and enhances cutting efficiency, offering users peace of mind that their tool is well-maintained during operation.

The chainsaw also boasts a tool-less chain tensioning system, allowing for quick and easy adjustments to the chain tension. This user-friendly feature saves time during maintenance and ensures optimal performance at all times.

Safety is a top priority in the design of the Poulan 96042003505. The chainsaw is equipped with a chain brake that quickly stops the chain in case of kickback, reducing the risk of injury. Additionally, the ergonomic handle design provides a comfortable grip, allowing users to maintain control while minimizing strain.

In summary, the Poulan 96042003505 is a well-rounded chainsaw that combines power, efficiency, and user-centric features. Its cutting-edge technologies and thoughtful design elements make it a dependable tool for both casual users and seasoned professionals alike.