Poulan 96042003505 manual To Adjust Steering Wheel Alignment, Front Wheel TOE-IN/CAMBER

Page 23

SERVICE AND ADJUSTMENTS

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

 

NEUTRAL

GEARSHIFT LEVER

LOCK GATE

 

 

ADJUSTMENT

 

BOLT

FIG. 33

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 34)

TO START ENGINE WITH A WEAK BATTERY (See Fig. 35)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

• Block up axle securely.

• Remove axle cover, retaining ring and washers to allow

wheel removal (rear wheel contains a square key - Do

not lose).

• Repair tire and reassemble.

• On rear wheels only: align grooves in rear wheel hub

and axle. Insert square key.

• Replace washers and snap retaining ring securely in

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

axle groove.

• Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 34

23

FIG. 35

REPLACING BATTERY (See Figs. 36 and 37)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from acci- dental grounding.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model PB19546LTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceIII. Children Table of Contents Key Slope Sheet Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Install Seat See FigsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigsReverse Operation System ROS See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig Before Starting the Engine To Start Engine See Fig Mowing TipsLubrication Chart MaintenanceCheck Operator Presence System BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs Install belt on engine pulley M To Level Mower To Replace Motion Belt Drive See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Attach Jumper Cables To Adjust Steering Wheel AlignmentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Service Notes Fold Alon THI Dotted Line REE Lope Only Ride UP and Down Hill Not Across Hill Degrees MAXPage Page Degrés ’ENTRETIEN Remarques Défectueux est Dépannage DE GuideRalenti Entreposage Carburateur LE Régler Pour Starter DU Commande LA Régler PourGAZ DES Commande Réglages ET RévisionChargée Mentretièen Batterie Déchargée OU Faible Batterie Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourCarrossage AVANT/ Roues DES Convergence Tionrecdi LA DE L’ALIGNEMENT Régler PourTondeuse DE Lame DE Mentnetraî 33 .FigFIG LA Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour FIG LA Voir28 .FIG Tondeuse LA Niveau LE Ajuster Pour30 .FIG 29 .FIG23 .FIG 26 .FIG25 .FIG 24 .FIGFig Voir Cour LA ET Tondeuse LA InstallerReglages ET Revision Figs Voir D’ENTRAÎNEMENT RoieNettoyage Ligne EN Installé D’ESSENCE FiltreEntretien Fig la VoirMoteur Frein DU Fonctionnement Fig la Voir Lame LA EnleverLames DES Entretien PneusUtilisation Chaque Avant O I T a D N a M M O C E RLubrification DE Tableau 14 .FIG UtilisationTonte DE Conseils Moteur LE Démarrer PourET Charrettes DES Remorquer Pour Accessoires Autres’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE Vérifier10 .FIG Jauge DE Roues LES Régler Pour12 .FIG 11 .FIGTionsta DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourEt 7 .Figs la Voir Arrêter Pour Fig la Voir MentneDattachement Propriété la de lendommagement Toutes SI Vérifier Toutes SI Vérifier MontageCorrectement Sont Courroies LES Et 2 .Figs les Voir Siège LE Ajustez Fig la Voir Batterie LA VérifierCarton LE Deballer DU Tracteur LE Sortir PourPour Exigés Outils LES Tionrecdi DE Volant LE FixerMontar SIN Piezas 24-19 Réglages ET Révision Sommaire27-26 Dépannage DE Guide ’ESSENCE DE Sûre Manipulation Général EntretienTracteurs des sécurité toute ’utilisation pour ConseilsTracteurs des sécurité toute en l’utilisation pour Conseils PentesLES Dans Fonctionnement AUX Imprimé

96042003505 specifications

The Poulan 96042003505 is a high-performance chainsaw designed to meet the dynamic needs of both casual users and professional arborists. This robust tool is known for its reliability, efficiency, and ease of use, making it a popular choice among various outdoor maintenance enthusiasts.

One of the standout features of the Poulan 96042003505 is its powerful 42cc engine. This Two-Stroke engine delivers impressive cutting performance, allowing users to easily tackle a range of tasks from pruning trees to cutting firewood. The design emphasizes fuel efficiency and reduced emissions, aligning with modern environmental standards without compromising power.

Another key characteristic of the Poulan 96042003505 is its lightweight construction. Weighing in at approximately 12 pounds, it provides excellent maneuverability without sacrificing durability. The lightweight design means that users can operate the chainsaw for extended periods with reduced fatigue, making it ideal for large projects.

This chainsaw is equipped with a 16-inch bar, providing an optimal balance between cutting ability and control. The bar length allows users to cut through medium-sized trees and thick branches with ease, making it versatile for both residential and professional use.

Technologically, the Poulan 96042003505 features an automatic oiler system, ensuring a steady supply of lubrication to the chain. This system promotes longer chainsaw life and enhances cutting efficiency, offering users peace of mind that their tool is well-maintained during operation.

The chainsaw also boasts a tool-less chain tensioning system, allowing for quick and easy adjustments to the chain tension. This user-friendly feature saves time during maintenance and ensures optimal performance at all times.

Safety is a top priority in the design of the Poulan 96042003505. The chainsaw is equipped with a chain brake that quickly stops the chain in case of kickback, reducing the risk of injury. Additionally, the ergonomic handle design provides a comfortable grip, allowing users to maintain control while minimizing strain.

In summary, the Poulan 96042003505 is a well-rounded chainsaw that combines power, efficiency, and user-centric features. Its cutting-edge technologies and thoughtful design elements make it a dependable tool for both casual users and seasoned professionals alike.
Top Page Image Contents