Poulan 96042003505 manual To Replace Mower Blade Drive Belt See Fig, To Check Brake

Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 31)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work belt around both mandrel pulleys and idler pulleys.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower (See "To Install Mower" in this section of manual).

MANDRELIDLER

PULLEYPULLEYS

MANDREL

PULLEY

FIG. 31

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Place gear shift lever in neutral position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION BELT DRIVE (See Fig. 32)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all

22

belt guides and keepers.

E

F

A

G

B

D

02954

Manual

FIG. 32

•Remove belt from stationary idler (A) and clutching idler (B).

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (D).

•Remove belt downward from engine pulley (E).

•Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

•Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

•Pull belt toward front of tractor and roll belt onto engine pulley (E).

•Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (D). Be sure belt is inside the belt keeper.

•Install belt through stationary idler (A) and clutching idler (B).

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 33)

The transaxle should be in neutral when the gear shift lever is in neutral (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral.

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PB19546LT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Unassembled Parts Key Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Figs Check Battery See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Figs HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigReverse Operation System ROS See Fig Before Starting the Engine Mowing Tips To Start Engine See FigMaintenance Lubrication ChartBlade Removal See Fig BatteryTractor Check Operator Presence SystemEngine Cleaning IN-LINE Fuel Filter See FigTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M To Level Mower To Check Brake Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Replace Mower Blade Drive Belt See Fig To Replace Motion Belt Drive See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentReplacing Battery See Figs To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Alon THI Dotted Line REE LopePage Page Degrés ’ENTRETIEN Remarques Dépannage DE Guide Défectueux estRalenti Entreposage Réglages ET Révision Starter DU Commande LA Régler PourGAZ DES Commande Carburateur LE Régler PourTionrecdi LA DE L’ALIGNEMENT Régler Pour Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourCarrossage AVANT/ Roues DES Convergence Chargée Mentretièen Batterie Déchargée OU Faible BatterieFIG LA Voir 33 .FigFIG LA Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour Tondeuse DE Lame DE Mentnetraî29 .FIG Tondeuse LA Niveau LE Ajuster Pour30 .FIG 28 .FIG24 .FIG 26 .FIG25 .FIG 23 .FIGFigs Voir D’ENTRAÎNEMENT Roie Cour LA ET Tondeuse LA InstallerReglages ET Revision Fig VoirFig la Voir Ligne EN Installé D’ESSENCE FiltreEntretien NettoyageMoteur Pneus Fig la Voir Lame LA EnleverLames DES Entretien Frein DU FonctionnementLubrification DE Tableau O I T a D N a M M O C E RUtilisation Chaque Avant Moteur LE Démarrer Pour UtilisationTonte DE Conseils 14 .FIGMoteur DU D’HUILE Niveau LE Vérifier Accessoires Autres’ESSENCE Réservoir LE Remplir ET Charrettes DES Remorquer Pour11 .FIG Jauge DE Roues LES Régler Pour12 .FIG 10 .FIGFig la Voir Mentne GAZ DES Commande LA Utiliser PourEt 7 .Figs la Voir Arrêter Pour Tionsta DE Frein LE Engager PourDattachement Propriété la de lendommagement Correctement Sont Courroies LES MontageToutes SI Vérifier Toutes SI Vérifier Fig la Voir Batterie LA Vérifier Et 2 .Figs les Voir Siège LE AjustezTionrecdi DE Volant LE Fixer DU Tracteur LE Sortir PourPour Exigés Outils LES Carton LE DeballerMontar SIN Piezas 27-26 Dépannage DE Guide Sommaire24-19 Réglages ET Révision ’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationLES Dans Fonctionnement PentesTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

96042003505 specifications

The Poulan 96042003505 is a high-performance chainsaw designed to meet the dynamic needs of both casual users and professional arborists. This robust tool is known for its reliability, efficiency, and ease of use, making it a popular choice among various outdoor maintenance enthusiasts.

One of the standout features of the Poulan 96042003505 is its powerful 42cc engine. This Two-Stroke engine delivers impressive cutting performance, allowing users to easily tackle a range of tasks from pruning trees to cutting firewood. The design emphasizes fuel efficiency and reduced emissions, aligning with modern environmental standards without compromising power.

Another key characteristic of the Poulan 96042003505 is its lightweight construction. Weighing in at approximately 12 pounds, it provides excellent maneuverability without sacrificing durability. The lightweight design means that users can operate the chainsaw for extended periods with reduced fatigue, making it ideal for large projects.

This chainsaw is equipped with a 16-inch bar, providing an optimal balance between cutting ability and control. The bar length allows users to cut through medium-sized trees and thick branches with ease, making it versatile for both residential and professional use.

Technologically, the Poulan 96042003505 features an automatic oiler system, ensuring a steady supply of lubrication to the chain. This system promotes longer chainsaw life and enhances cutting efficiency, offering users peace of mind that their tool is well-maintained during operation.

The chainsaw also boasts a tool-less chain tensioning system, allowing for quick and easy adjustments to the chain tension. This user-friendly feature saves time during maintenance and ensures optimal performance at all times.

Safety is a top priority in the design of the Poulan 96042003505. The chainsaw is equipped with a chain brake that quickly stops the chain in case of kickback, reducing the risk of injury. Additionally, the ergonomic handle design provides a comfortable grip, allowing users to maintain control while minimizing strain.

In summary, the Poulan 96042003505 is a well-rounded chainsaw that combines power, efficiency, and user-centric features. Its cutting-edge technologies and thoughtful design elements make it a dependable tool for both casual users and seasoned professionals alike.
Top Page Image Contents