Poulan PR25PH48STA To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 13

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT: BE SURE TO READJUST GAUGE WHEELS IF YOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

ATTACHMENT CLUTCH

ATTACHMENT

SWITCH PULL OUT TO

LIFT LEVER

"ENGAGE"

HIGH

 

POSITION

 

LOW

 

POSITION

PUSH IN TO

 

"DISENGAGE"

 

FIG. 10

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

•To restart movement, slowly release parking brake and brake pedal.

•Slowly depress appropriate drive pedal to slowest set- ting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 7 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

FIG. 11

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents PR25PH48STA Safe Operation Practices for Ride-On Mowers Safety RulesSafety Rules Table of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Battery Reverse Forward FastKnow Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionService Dates Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Muffler CleaningSpark Plugs Engine OIL FilterTo Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Remove Hood and Grill Assembly See Fig Replacing Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Choke Control See Fig To Adjust Throttle Control Cable See FigTo Adjust Carburetor Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsOFF Tractor Model Number PR25PH48STA SchematicNON-REMOVABLE Removable Connections Connections Electrical KEY Part Description Chassis and Enclosures Bracket Fender Drive Repair PartsTransaxle Order parts from Steering Assembly 175118 Bolt Shoulder 7/16-20 Unc 175553 Clip Engine Seat Assembly Wheels & Tires DecalsMower Lift Mower Deck Washer, Spacer Mower Vented Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Service Notes Service Notes Parts and Service

PR25PH48STA specifications

The Poulan PR25PH48STA is a powerful and versatile lawn mower designed for homeowners who seek a reliable solution for lawn care. This model is particularly known for its robust performance, ease of use, and advanced features that make mowing lawns a seamless experience.

One of the main features of the Poulan PR25PH48STA is its 25cc two-cycle engine, which provides strong power while ensuring efficient fuel consumption. This engine is designed for durability and performance, allowing users to tackle various types of grass and terrain without struggle. The lightweight design of the mower makes it easy to maneuver, providing users with greater control while mowing.

The PR25PH48STA also boasts a 48-inch cutting deck that enables a wider cutting path, allowing for quicker mowing sessions. This feature is especially beneficial for larger lawns, as it reduces the number of passes needed to achieve a well-manicured look. Additionally, the deck is equipped with multiple height adjustments, allowing users to select the perfect cutting height for their lawn's unique needs.

One innovative technology featured in the Poulan PR25PH48STA is its automatic choke system. This technology simplifies the starting process, making it easier for users to start the mower with minimal effort. The automatic choke adjusts as needed, ensuring optimal engine performance under diverse conditions.

Another notable characteristic of the PR25PH48STA is its ergonomic handle design. The handle is adjustable, allowing users to comfortably operate the mower without straining their backs or arms. This thoughtful design enhances user comfort, particularly during extended mowing sessions.

For added convenience, the Poulan PR25PH48STA features a reliable rear-wheel drive system that provides improved traction and stability on different terrains. This feature is especially useful for navigating hilly or uneven lawns, ensuring users can maintain control throughout the mowing process.

In summary, the Poulan PR25PH48STA is an excellent choice for homeowners who prioritize performance and convenience in their lawn care equipment. With its powerful engine, wide cutting deck, automatic choke system, and ergonomic design, this mower stands out as a reliable option for maintaining a beautiful lawn with ease. Whether dealing with large open spaces or intricate landscaping, the PR25PH48STA is engineered to make lawn maintenance effective and enjoyable.
Top Page Image Contents