Poulan 952802031 Notch CUT and Felling the Tree, Cutting a Fallen Tree, Important Points

Page 12

NOTE: If the tree has large buttress roots, remove them before making the notch. If us- ing saw to remove buttress roots, keep saw chain from contacting ground to prevent dull- ing of the chain.

NOTCH CUT AND FELLING THE TREE

SMake notch cut by cutting the top of the notch first. Cut through 1/3 of the diameter of the tree. Next complete the notch by cut- ting the bottom of the notch. See illustra- tion. Once the notch is cut remove the notch of wood from the tree.

Final (felling) cut here, 2 inches (5 cm) above center of notch.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen tree to the desired log size.

WARNING: Do not stand on the log being cut. Any portion can roll causing loss of footing and control. Do not stand downhill of the log being cut.

IMPORTANT POINTS

SCut only one log at a time.

S Cut shattered wood very carefully; sharp pieces of wood could be flung toward opera- tor.

S Use a sawhorse to cut small logs. Never

allow another person to hold the log while

cutting and never hold the log with your leg

First cut

Notch

Second cut

Hinge

or foot.

SDo not cut in an area where logs, limbs, and roots are tangled such as in a blown down area. Drag the logs into a clear area before cutting by pulling out exposed and cleared logs first.

TYPES OF CUTTING USED FOR BUCKING

WARNING: If saw becomes

S After removing the wood from the notch, make the felling cut on the opposite side of the notch. This is done by making a cut about two inches (5 cm) higher than the center of the notch. This will leave enough uncut wood between the felling cut and the notch to form a hinge. This hinge will help prevent the tree from falling in the wrong direction.

Hinge holds tree on stump and helps control fall

Opening of felling cut

Closing of notch

NOTE: Before felling cut is complete, use wedges to open the cut if necessary to control the direction of fall. To avoid kickback and chain damage, use wood or plastic wedges, but never steel or iron wedges.

SBe alert to signs that the tree is ready to fall:

cracking sounds, widening of the felling cut, or movement in the upper branches.

SAs tree starts to fall, stop saw, put it down, and get away quickly on your planned re- treat path.

SDO NOT cut down a partially fallen tree with your saw. Be extremely cautious with partially fallen trees that may be poorly supported. When a tree doesn’t fall com- pletely, set the saw aside and pull down the tree with a cable winch, block and tackle, or tractor.

pinched or hung in a log, don’t try to force it out. You can lose control of the saw resulting in injury and/or damage to the saw. Stop the saw, drive a wedge of plastic or wood into the cut until the saw can be removed easily. Re- start the saw and carefully reenter the cut. To avoid kickback and chain damage, do not use a metal wedge. Do not attempt to restart your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

Turn saw OFF and use a plastic or wooden wedge to force cut open.

Overcutting begins on the top side of the log with the bottom of the saw against the log. When overcutting use light downward pres- sure.

Overcutting

Undercutting

Undercutting involves cutting on the under- side of the log with top of saw against the log. When undercutting use light upward pres- sure. Hold saw firmly and maintain control. The saw will tend to push back toward you.

WARNING: Never turn saw upside down to undercut. The saw cannot be con- trolled in this position.

Always make your first cut on the compres- sion side of the log. The compression side of the log is where the pressure of the log’s weight is concentrated.

12

Image 12
Contents Manual de Instrucciones Manuel d’Instructions Using the chain saw Always use two hands when operating the chain sawStarting Reminder Plan AheadOperate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlAvoid Pinch-Kickback Avoid Pull-InKickback Safety Features Chain Brake and CKA AngleIf your hand slips off the front handlebar Assembly Attaching the BAR & Chain If notAdjusting the tension Chain TensionChecking the tension Operation Before Starting Engine Fueling Engine Fuel RequirementsBAR and Chain Lubrication Important Points to Remember Starting a Warm EngineDifficult Starting or starting a flooded engine Kickback occursBraking function control Caution The chain brake must be Inertia activating function controlOperating Tips Tree Felling TechniquesNotch CUT and Felling the Tree Cutting a Fallen TreeImportant Points Types of Cutting Used for BuckingBucking Using a LOG or Support Stand Bucking Without a SupportLimbing and Pruning Important Points LimbingService Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelChain Adjustment Replace Spark PlugTo Sharpen Chain Replace Fuel FilterCarburetor Adjustment StorageCooling System Seasonal StorageLoad Adjustment Engine EngineOther Charlotte, NC Canada, contact Poulan PROLigations The U.S. Environmental

952802124, 952802030, 952802031 specifications

Poulan, a respected name in outdoor power equipment, offers a range of innovative products designed for lawn care and maintenance. Among its extensive lineup, the models 952802124, 952802030, and 952802031 stand out due to their powerful functionalities and user-friendly features. Each of these models incorporates advanced technologies aimed at enhancing the user experience and ensuring efficient operation.

The Poulan 952802124 model is primarily recognized for its robust performance. It boasts a powerful engine that allows it to handle various tasks with ease. Whether you need to tackle thick grass or overgrown weeds, this model has the capability to deliver optimal results. It features a durable cutting deck that provides an even cut while minimizing the need for multiple passes, ultimately saving time and effort.

In terms of user comfort, the 952802124 integrates ergonomic handles designed for better control and reduced fatigue. This is especially beneficial for extended periods of use, making it a reliable choice for both homeowners and professional landscapers. Additionally, the model is equipped with a quick-start technology, ensuring that you can get to work without unnecessary delays.

The Poulan 952802030 model places a strong emphasis on versatility. It comes with interchangeable attachments, allowing users to customize their equipment according to specific needs. Whether it's leaf blowing, mulching, or trimming, the 952802030 adapts to various tasks efficiently. This flexibility makes the model suitable for different seasons and environments, providing year-round functionality.

Moreover, state-of-the-art safety features are integrated into the design of the 952802030, including a safety lock mechanism that prevents accidental starts, ensuring the user's safety during operation. The lightweight construction also allows for easy maneuverability, making it an ideal choice for navigating tight spaces or uneven terrain.

Meanwhile, the Poulan 952802031 rounds out this trio with its emphasis on energy efficiency. The model is engineered to reduce fuel consumption without compromising performance. It incorporates technologies designed to minimize emissions, aligning with environmentally-friendly practices and regulations. The 952802031 also features an easy-to-access air filter, which simplifies maintenance and prolongs the life of the engine.

In summary, the Poulan 952802124, 952802030, and 952802031 represent excellent choices in the realm of outdoor power equipment. With an emphasis on performance, versatility, safety, and environmental responsibility, these models are well-suited for a variety of lawn care needs, making them valuable investments for consumers. Each model embodies Poulan's commitment to quality and innovation, ensuring satisfaction for both casual users and professionals alike.