Poulan 530163653 instruction manual Cutting a Fallen Tree, Types of Cutting Used for Bucking

Page 12

S DO NOT cut down a partially fallen tree with your saw. Be extremely cautious with partially fallen trees that may be poorly supported. When a tree doesn’t fall com- pletely, set the saw aside and pull down the tree with a cable winch, block and tackle, or tractor.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen tree to the desired log size.

WARNING: Do not stand on the log being cut. Any portion can roll causing loss of footing and control. Do not stand downhill of the log being cut.

IMPORTANT POINTS

SCut only one log at a time.

SCut shattered wood very carefully; sharp pieces of wood could be flung toward oper-

ator.

SUse a sawhorse to cut small logs. Never allow another person to hold the log while

cutting and never hold the log with your leg or foot.

S Do not cut in an area where logs, limbs, and roots are tangled such as in a blown down area. Drag the logs into a clear area before cutting by pulling out exposed and cleared logs first.

TYPES OF CUTTING USED FOR BUCKING

WARNING: If saw becomes pinched or hung in a log, don’t try to force it out. You can lose control of the saw resulting in injury and/or damage to the saw. Stop the saw, drive a wedge of plastic or wood into the cut until the saw can be removed easily. Re- start the saw and carefully reenter the cut. To avoid kickback and chain damage, do not use a metal wedge. Do not attempt to restart your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

WARNING: Never turn saw upside down to undercut. The saw cannot be con- trolled in this position.

Always make your first cut on the compres- sion side of the log. The compression side of the log is where the pressure of the log’s weight is concentrated.

First cut on compression side of log

Second cut

Second cut

First cut on compression side of log

BUCKING WITHOUT A

SUPPORT

SOvercut through 1/3 of the diameter of the log.

SRoll the log over and finish with a second

overcut.

SWatch for logs with a compression side to prevent the saw from pinching. See il- lustrations for cutting logs with a compres- sion side.

BUCKING USING A LOG OR SUPPORT STAND

SRemember your first cut is always on the compression side of the log.

(Refer to the illustrations below for your

first and second cut)

S Your first cut should extend 1/3 of the diameter of the log.

SFinish with your second cut.

Using a log for support

2nd Cut

Turn saw OFF and use a plastic or wooden wedge to force cut open.

Overcutting begins on the top side of the log with the bottom of the saw against the log. When overcutting use light downward pres- sure.

Overcutting Undercutting

Undercutting involves cutting on the under- side of the log with top of saw against the log. When undercutting use light upward pres- sure. Hold saw firmly and maintain control. The saw will tend to push back toward you.

2nd Cut

12

1st Cut

1st Cut

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Operate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackKickback Safety Features Reduce the Chance KickbackMaintain Control Your left arm straight with the elbow lockedChain Brake and CKA Angle Computed kickback angle CKA TableFront Hand Guard, designed to reduce Attaching the BAR & Chain If not Tip BarCutters Depth Gauge Drive Links Adjusting the tension Chain Tension Including units with chain already installedChecking the tension ON/STOP Switch Know Your SAWThrottle Trigger Throttle LockoutFueling Engine BAR and Chain LubricationImportant Points to Remember Handle Right foot through rear handleStarting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlTree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Gine can resultBucking Using a LOG or Support Stand Cutting a Fallen TreeTypes of Cutting Used for Bucking Bucking Without a SupportPruning Limbing and Pruning Important PointsLimbing AIR FilterCleaning the air filter Carburetor AdjustmentBAR Maintenance Inspect Muffler and Spark Arresting ScreenNeed Service PART? Chain SharpeningIgnition Timing Spark PlugTroubleshooting Table Cause Remedy Your Warranty Rights and OB Ligations The U. S. Environmental

530163653 specifications

The Poulan 530163653 is a versatile and efficient tool designed to meet a range of outdoor maintenance needs. Whether you are a professional landscaper or a casual gardener, this equipment is engineered to provide excellent performance and reliability.

One of the standout features of the Poulan 530163653 is its powerful engine. Equipped with a robust, sturdy motor, it delivers consistent power for various tasks. This ensures that you can tackle everything from heavy-duty cutting to light trimming without compromising efficiency. The engine is designed to handle different types of vegetation, making it a versatile addition to your toolkit.

Another noteworthy aspect of this model is its lightweight design. Weighing significantly less than comparable models, the Poulan 530163653 reduces user fatigue, allowing for longer operating periods without discomfort. This feature is particularly appreciated by those who must perform extensive landscaping work or maintenance over large areas.

In terms of user comfort, the Poulan 530163653 has an ergonomically designed handle. This design promotes a natural grip and reduces strain during extended use. Additionally, the anti-vibration technology integrated into the equipment minimizes hand fatigue and provides a smoother operation.

Durability is at the core of the Poulan 530163653's design. The materials used in its construction are resistant to wear and tear, ensuring that the tool can withstand challenging conditions and frequent use. Moreover, the ease of maintenance is another key characteristic, as the equipment is designed for simple cleaning and repairs, allowing for longer service life.

The Poulan 530163653 also features advanced cutting technologies, including a dual-line trimming system that enhances cutting efficiency. This mechanism allows for a wider cutting path, ensuring that you can complete jobs more quickly and effectively. The ability to adjust the cutting height gives users greater control over their landscaping tasks.

In conclusion, the Poulan 530163653 stands out in the market for its powerful engine, lightweight construction, ergonomic design, and advanced cutting technologies. Its durability and ease of maintenance further enhance its appeal, making it a reliable choice for both professional and home use. Whether you're tackling grass trimming, hedge shaping, or clearing brush, the Poulan 530163653 delivers the performance and efficiency required for a range of outdoor tasks.
Top Page Image Contents