Roberts Gorden 75, 100, 125, 45, 30, 60 service manual Replacement Parts, Burner Components

Page 48

UHA LOW PROFILE UNIT HEATER INSTALLATION OPERATION AND SERVICE MANUAL

SECTION 14: REPLACEMENT PARTS

WARNING

Explosion Hazard

Installation, service and annual inspection must be done by a contractor qualified in the installation and service of gas-fired heating equipment or your gas supplier.

Turn off gas and electrical supplies before performing service or maintenance.

Failure to follow these instructions can result in death, injury or property damage.

See warnings and notes on Page 35, Section 12 before removing or replacing parts.

Burner Components

All serviceable burner parts are accessed by the door on the side of the heater. Remove the sheetmetal screws.

14.1 Gas Valve

Remove the gas supply pipe at the heater inlet. Follow steps in Section 14.2 and Section 14.2.1 to remove gas valve/manifold.

Replace in reverse order. Verify that the gas flow direction of the valve is correct. Use a minimum amount of gas seal on the thread joint. Check that all the joints are leak free. Reset gas valve. See Page 31, Section 10.2.2.

IT IS IMPORTANT THAT ONLY THE CORRECT GAS VALVE IS USED WHEN REPLACING THESE CONTROLS.

NOTE: Seperated combustion

model shown.

Flexible Air Duct

 

½PSI

 

 

C

IN

 

 

ON

 

OFF

Description

Part Number

Gas Valve, NG (Models UHA[X][S] 30 - 45)

90034500

Gas Valve, LP (Models UHA[X][S] 30 - 45)

90034600

Gas Valve, NG (Models UHA[X][S] 60 - 125)

90032505

Gas Valve, LP (Models UHA[X][S] 60 - 125)

90032506

42

 

Image 48
Contents Blackheat Page Roberts-Gordon LLC Page Table of Figures Page Heater Safety Manpower RequirementsSafety Labels and Their Placement UHA 30 45 Label Placement UHA 60 75 Label Placement UHA 100 125 Label Placement Installer Responsibility Wall TagCorrosive Chemicals National Standards and Applicable CodesMinimum Required Installation Clearances Critical Considerations 3.1 Basic InformationManufactured Units Clearances to CombustiblesGas Supply Electrical SupplyVent National Standards and Applicable Codes High Altitude Major Components 5.1 General Shelf Mounting and SuspensionWall Mounting Suspension Methods Wall Shelf Mounting and Hanging Suspension Vertical Louvers Optional Vent Installation VentingChanging Vent and Air Intake Orientation United States RequirementsStandard Vented Heaters Models Uhax 30 Separated Combustion Heaters Models Uhaxs 30Unvented Operation Horizontal VentingVertical Venting Length RequirementsMaximum Vent Lengths Vent MaterialVent and Roof Detail Standard Vented Heater Common Vertical Vent Termination Concentric Vent Box Vertical Separated Combustion Installation Unvented InstallationAIR Supply Building VentilationGAS Piping ConnectionsWiring Positioning ThermostatsFan Control Low Voltage Thermostat with One HeaterLow Voltage Thermostat with Multiple Heaters 30 Low Voltage Thermostat with Multiple Heaters 60 Internal Wiring Diagram TransformerLadder Wiring Diagram FlameElectrical Connection to the Heater Operation and Maintenance Pressure Regulator Gas Outlet Outlet Pressure Pressure Switch Check Gas RateTurning Off the Heater Complete Start-Up Instruction to the UserUser Instructions User InstructionsHeater Operation Lighting Instructions 11.4.1 To Turn On HeaterSimple Troubleshooting Simple Troubleshooting Burner FaultsTo Turn the Heater Off Servicing Maintenance Checklist Venting and Air Intake PipeVicinity of the Heater Vehicles and OtherWhen installed Wall Tag Combustion Air IntakePipe Heat ExchangerTroubleshooting 13.1 General Troubleshooting For Automatic Ignition Burner Systems Conduct start-up procedure as shown on Page 29, SectionTroubleshooting for Flame Supervision System Troubleshooting for Gas Valves Troubleshooting for Flue BlowerReplacement Parts Burner ComponentsBurner Compartment Burner InjectorsIgnition Electrode and Flame Probe Louver and Louver Springs Re-usedFlue Blower Vertical Installation Axial Fan/Guard/Motor Assembly Ignition ControlFan Removal and Replacement To Replace the Fan AssemblyLimit Switches Removal and Replacement Specifications 15.1 Dimension Data Model UhaxsGeneral Technical Data Table All Models Technical Data Table All ModelsWarranty is Void if Roberts Gordon will not PAY forRoberts-Gordon Limitations on Authority RepresentativesPage Owner Warranty Registration Card Page Page Some objects can catch fire or explode when placed
Related manuals
Manual 60 pages 21.77 Kb

60, 30, 45, 125, 100 specifications

Roberts Gordon is a recognized leader in the manufacturing of innovative heating solutions, with a diverse product line including the 100, 125, 75, 45, and 60 series of radiant tube heaters. Each model is designed to meet specific heating needs while emphasizing efficiency, durability, and performance.

The Robert Gordon 100 series is known for its high efficiency and ability to provide consistent warmth in large industrial spaces. It features advanced infrared technology, which heats objects and surfaces directly, resulting in quicker temperature increases and enhanced comfort. This model is equipped with modulating burners that allow for optimal gas usage and can be easily integrated into existing systems.

The 125 series builds upon the efficiency of the 100 model while offering increased heating capacity. Its robust design ensures it can handle the demands of larger applications, such as warehouses and manufacturing facilities. With enhanced control options, users can tailor the heating output to match specific operational requirements, reducing energy consumption.

The 75 series offers a compact solution for smaller commercial spaces, providing a reliable heating source without taking up excessive floor space. Its lightweight design facilitates easy installation, while the modular approach allows for scalability to meet changing heating demands. This series emphasizes sustainability, utilizing advanced combustion technologies that minimize emissions.

For smaller applications, the 45 series stands out with its efficient heating capabilities in confined spaces. This series features simple, yet effective controls, enabling straightforward operation. The robust construction ensures durability, making it well-suited for different commercial environments, including retail settings or small workshops.

Finally, the 60 series combines the best features of the range with energy conservation as a primary focus. Its innovative design incorporates smart technology to monitor energy usage and optimize performance. The heaters are equipped with the latest in safety features, providing peace of mind for users.

Overall, Roberts Gordon’s radiant tube heaters showcase a commitment to high-quality heating solutions that cater to a variety of industrial and commercial applications. With energy efficiency, superior durability, and advanced heating technologies as core characteristics, Roberts Gordon remains a trusted choice for businesses looking to enhance their heating performance.