Rheem GEN15ADC-E Standard Operation, Installation Inspection, Wireless Monitor Status LED’s

Page 38

Standard Operation:

Wireless Monitor Status LED’s

 t 5IFXJSFMFTTNPOJUPSSFDFJWFTEBUBGSPNUIFHFOFSBUPS every 10 minutes and displays the generator status through 3 LED’s.

t 1SFTTJOHUIFSYSTEM UPDATE button will provide current generator status by flashing the status LED’s. When pressed, all 3 LEDs will flash until the generator status is received.

NOTICE Generator control panel must be in AUTO mode or no communication with monitor will occur.

t *OPSEFSUPDPOTFSWFQPXFSBOEUPFYUFOECBUUFSZMJGF the LED’s are not lit continuously; instead they are briefly flashed as indicated below.

NOTICE During the weekly exercise cycle, the generator will run for 20 minutes, but it will not supply power to the home. During the exercise cycle, the monitor will continue blinking the GENERATOR READY green LED.

 t (&/&3"5033&"%:8IFOBDUJWFUIFHSFFO-&%XJMM flash once every 7 seconds. The green LED indicates that the generator is in AUTO mode and that it is ready to run in the event of a loss of utility power.

 t (&/&3"503108&38IFOBDUJWFUIFHSFFO-&%XJMM flash every 7 seconds. The green LED indicates that the generator is supplying power.

 t 4&37*$&/&&%&%8IFOBDUJWFUIFSFE-&%XJMMGMBTI in a sequence that corresponds to the service code. For example, when Low Frequency scrolls across the control board, the red LED will flash 5 times with a 3 second pause between series of blinks until it is reset or the condition is corrected. When the red LED is lit, contact your nearest authorized service dealer.

NOTICE None of the conditions on the display unit can be cleared at the wireless monitor. All alerts must be cleared at the generator control panel.

NOTICE Service conditions will only be displayed on the basic monitor when the control board is placed in AUTO mode.

Other:

LED Lighting Codes

t #BUUFSJFT*OTFSUFEGENERATOR READY LED will light for 5 seconds.

t 8JSFMFTT$PNNVOJDBUJPO-PTUSERVICE NEEDED LED will flash 20 fast pulses, then pause for 5 seconds, and repeat the sequence until the communication has been restored.

NOTICE Communication lost issues can typically be resolved by moving the wireless monitor closer, within the home, to the standby generator.

t -JOLJOH&SSPSPS/PU-JOLFESERVICE NEEDED LED will light for 4 seconds, pause for 4 seconds, and repeat the sequence until a successful link is completed.

Installation Inspection

Before placing the generator system into service, inspect the entire installation carefully.

This completes the installation and start-up instructions. The operator’s manual provides full details on Operation, Maintenance and Troubleshooting for this generator system.

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Generator Systems Engine For Future ReferenceDate of Purchase Generator Table of Contents Important Safety Instructions Safety Symbols and MeaningsFlammable and explosive, which could cause  Tie up long hair and remove jewelry Owner Responsibilities Installing Dealer/Contractor ResponsibilitiesEquipment Description Cold Weather KitDelivery Inspection Unpacking PrecautionsShipment Contents Owner Information Installation ChecklistInstalling Contractor Information Unit InformationIntentionally Left Blank Generator Placement Exhaust Side of the Generator t &OTVSFFYIBVTUHBTJTLFQUBXBZGSPN Windows C doors Other General Location Guidelines Annex a Explanatory Material Placement of Standby Generator to Reduce the Risk of FireRequirements Generator Installations AAAElectrical and Fuel Inlet Locations Lifting the Generator Concrete Anchoring of UnitAccess Ports To open roof To remove battery panelTo secure battery panel To remove front panelGaseous Fuel System  t 8IFSFMPDBMDPOEJUJPOTJODMVEFFBSUIRVBLFFuel Consumption LP Vapor Natural Content of FuelPower Loss LP Vapor PropaneFuel Conversion System Connectors Generator AC Connection System Grounding the Generator Generator Power ConnectionTransfer Switch Communication Utility Circuit ConnectionSystem Control Panel Generator Operation Control ButtonsMenu MenuGeneral Set Up Screen SET TimeGeneral System Parameters Automatic ModeControl Panel Prompts Advanced Settings Screen Prompts as outlined belowBattery Service Code Detection SystemFinal Installation Considerations Battery Standard Cold Start SpecificationsInitial Start-up No Load Electronic Governor System Electronic Governing CheckSetting Exercise Timer Automatic Operation SequenceAntenna Installation Wireless Monitor # of flashes Service neededWireless Monitor Operation SystemSYSTEM UPDATEupdateStandard Operation Installation InspectionWireless Monitor Status LED’s OtherSchematic / Wiring Diagrams Schematic DiagramWiring Diagram On Some UNITS, Wire 1 MAY Also be Labeled AS Wire

GEN15ADC-E, GEN16AD-E, GEN20AD-E, Rheem / Ruud standby generator specifications

The Rheem GEN16AD-E, GEN20AD-E, and GEN15ADC-E models are part of Rheem and Ruud's innovative line of standby generators, designed to provide reliable power solutions for both residential and commercial applications. These generators deliver robust performance, ensuring uninterrupted power supply during outages and emergencies.

The GEN16AD-E and GEN20AD-E generators are particularly noteworthy for their advanced features and technologies. They are equipped with automatic voltage regulation, which helps maintain a steady power supply and protects your appliances from voltage fluctuations. These models also feature a state-of-the-art controller with an LCD display, allowing users to monitor generator performance and status easily. Moreover, they come with a durable, weather-resistant enclosure that is built to withstand various environmental conditions, ensuring longevity and reliability.

Both the GEN16AD-E and GEN20AD-E models incorporate cutting-edge noise reduction technologies, making them some of the quietest generators on the market. This is a significant advantage for residential areas, where noise levels must be kept to a minimum for the comfort of families and neighbors alike. Additionally, their compact design allows for easy installation in limited spaces, making them versatile for various property layouts.

The Rheem / Ruud standby generators are also designed with fuel efficiency in mind. With advanced engine designs and power management features, these units optimize fuel consumption, providing significant cost savings over time. Automatic start systems enhance convenience, enabling the generator to kick in as soon as an outage is detected. This ensures you are never left without power, no matter the circumstances.

The GEN15ADC-E model focuses on delivering a balance of power and efficiency for smaller applications, making it ideal for homeowners looking for lower-capacity solutions without compromising on performance. It also offers features such as digital control panels for easy monitoring and maintenance.

Overall, the Rheem GEN16AD-E, GEN20AD-E, and GEN15ADC-E standby generators exemplify reliability, efficiency, and user-friendly design. With their impressive features and modern technologies, these generators are a smart investment in power security, ensuring that your home or business stays operational even during unexpected power outages. Their strong reputation in the market reflects the commitment of Rheem and Ruud to provide high-quality products that meet the diverse needs of their customers.
Top Page Image Contents