Scag Power Equipment STC61V-25CV-FR, STC61V-23BV Starting the Engine, Ground Travel and Steering

Page 18

R

Section 4

4.4 STARTING THE ENGINE

CAUTION

DO NOT USE STARTING FLUIDS. Use of starting fluids in the air intake system may be potentially explosive or cause a “runaway” engine condition that could result in engine damage and/or personal injury.

1.Be sure the fuel shutoff valve, located behind the operator's seat, is completely open. (See Section 7.5.)

2.Secure the ROPS in the upright and locked position.

3.Sit in the operator’s seat, fasten seat belt and place the steering control levers in the neutral position.

4.Engage the parking brake.

5.Place the PTO switch in the disengaged position.

6.If the engine is cold, choke the engine as needed.

7.Move the engine throttle control to about half engine speed.

8.Turn the ignition key to the START position and release the key as soon as the engine starts. Do not hold the key in the START position for more than 15 seconds at a time. Allow at least 60 seconds between each cranking attempt to prevent overheating of the starter motor. Prolonged cranking can damage the starter motor and shorten battery life.

Learn to feather the steering controls to obtain a smooth operating action.

Practice operating the mower until you are comfortable with the controls before proceeding to mow.

Forward Travel

To travel forward with the mower, disengage the parking brake, pull levers inward out of the neutral lock position and slowly push the steering control levers forward an equal distance. The further the steering control levers are pushed forward the greater the forward speed will be. To increase the speed, push the steering control levers further forward and to decrease the speed, pull the steering control levers back.

To stop the forward travel, pull the steering control levers back to the neutral position.

To steer the mower left while traveling forward, pull the left steering lever back.The further the lever is pulled back, the quicker the mower will turn left.

To steer the mower right while traveling forward, pull the right steering control lever back. The further the lever is pulled back, the quicker the mower will turn right.

- NOTE -

Smooth operation of the steering levers will produce smooth mower operation. While learning the operation of the steering controls, keep the travel speed low.

9. Allow engine to warm before operating the mower.

4.5 GROUND TRAVEL AND STEERING

- IMPORTANT -

If you are not familiar with the operation of a machine with lever steering and/or hydrostatic transmissions, the steering and ground speed operations should be learned and practiced in an open area, away from buildings, fences, or obstructions.

Learn the operation on flat ground before operating on slopes.

Start practicing with a slow engine speed and slow forward travel.

14

- IMPORTANT -

Do not travel forward over a curb. The mower will hang up on the curb. Raise the deck and travel backwards over the curb at a 45 degree angle. (See Figure 4-1 items 12-14 for cutter deck raising description.)

Image 18
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited Warranty Commercial Equipment Inside Back CoverDirection Reference General InformationIntroduction Servicing The Engine and Drive Train ComponentsSymbols Symbol DescriptionSafety Information Signal WordsBefore Operation considerations Operation Considerations Section Roll-over protection system Foldable Roll-over protection system if equippedFoldable Roll-Over Protection System Maintenance Considerations & storage Safety and Instructional Decals Install Belt COvER BeforeElectrical SpecificationsEngine TractorHydraulic System Weights and Dimensions 48V 52V 61VCutter Deck ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Initial RUN-IN ProceduresStarting the Engine Ground Travel and SteeringForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelAfter Operation Hillside OperationParking the Mower Removing Clogged MaterialAdjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Adjusting the Steering Levers Towing optional hitch accessoryTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Adjustments Parking Brake AdjustmentTravel Adjustments Neutral Adjustment Tracking AdjustmentCutter Deck Adjustments Throttle Control and Choke AdjustmentsBelt Adjustment Belt AlignmentAdjustment ROD Lock NUT Cutter Deck Pitch Cutter Deck HeightCustom-Cut Baffle Adjustment Position Custom-Cut Baffle Adjustment eARLY mODELSPosition Custom-Cut Baffle Adjustment cURRENT pRODUCTION Position Custom-Cut Baffle Adjustment Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine Oil Engine Fuel SystemEngine Air Cleaner Cleaning and/or Replacing Air Cleaner ElementReplacing In-Line Fuel Filter Elements Battery Charging the BatteryJump Starting Cutter Blades Blade ReplacementDrive Belts Blade InspectionTires BODY, DECK, and UpholsteryIllustrated Parts List Scag Approved Attachments and Accessories48V & 52V Cutter Decks Description 61V Cutter Deck 424367 Dust Shield 483210 Idler Pulley, 5 Dia Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 482619 Tire, 13 x 6.5-6 Smooth 483736 STC Fixed ROLL-OVER Protection System STC Fixed ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System Drive System Components 04019-04 Nut, Serr. Flange 3/8-16 04001-136 Engine & Attaching Parts Engine and Attaching Parts Steering Components Damper orange colored print Damper blue colored print Brake Components Brake Components 33 47 Fuel and Hydraulic System Electrical System Battery, 330CCA Not Available Through Scag BDP-10A Hydraulic Pump Assembly Housing Kit Install Belt COvER Before Operating Machine482166R STC 2008 RDP2 Electrical Schematic Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Precaución LlantasCuchilla la de Reemplazo .C Cuchilla la de Reemplazo 9-7 FiguraPara apropiada protección la lleve Siempre Cuchillas las de Afilado 8-7 FiguraSeguridad garantizar para Transmisión DE CorreasCorte DE Cuchillas Rajada o rota cuchilla una suelde nuncaBatería Gases producen ácido-plomo baterías Las AdvertenciaDel elemento del reemplazo y/o Limpieza .A Motor DEL Combustible DE SistemaCárter del aceite de Cambio .B Cárter del aceite de nivel del Verificación .AAceite de filtro del elemento del Cambio .C Hidráulico Sistema Hidráulico aceite de Cambio .BHidráulico aceite de nivel del Verificación .A Lubricación DE Grasa DE Conexiones Figura LA VEA Grasa DE Conexión DE Lubricación DE Tabla LubricaciónMantenimiento Recomendados Servicio DE Intervalos Mantenimiento DE TablaSección Posiciones De personalizado corte de deflector del AjusteCorte de plataforma la de Altura Corte Corte de plataforma la de InclinaciónCorte de plataforma la de Nivel DE Plataforma LA DE AjustesAjustes Estrangulación Aceleración DE Control Correa LA DE AlineaciónCorrea LA DE Ajuste Alineación de AjusteNeutral Ajuste Desplazamiento DE AjustesDirección De control de varilla la de Ajuste .3-6 Figura Ajustes DE Freno DEL AjusteFreno de Ajuste .1-6 Figura Solución Causa Condición Solución Causa Condición Continuación Fallas DE Solución De Franjas Vetas Corte de trayectoriasEntre cortar sin césped La en cortar sin céspedOpcional Enganche de accesorio Remolque Advertencia PlataformaDetenido Motor EL CON Cortacésped DEL Desplazamiento Atascado Material DEL RetiroCortacésped DEL Estacionamiento Cuesta UNA EN Operación Corte DE Cuchillas Plataforma DE Transmisión LA DE ConexiónPrecaución Dirección Y Terreno EL EN DesplazamientoMotor DEL Arranque Seguridad DE Bloqueo DE SistemaFigura combustible de cambio de Válvula Instrumentos Controles DE IdentificaciónProductividad Corte DE PlataformaEléctrico Sistema TractorSeguridad DE Y Instructivas Calcomanías Cuchillas las suelde NUNCAni enderece.cuchillas Almacenamiento Y Mantenimiento DE ConsideracionesRops del Bisagra 2-2 Figura Vuelco contra protección de plegable Sistema 1-2 FiguraVuelco Contra Protección DE Sistema Advertencia Operación DE ConsideracionesAdvertencia Operación LA a Previas Consideraciones Señalización DE PalabrasIntroducción Descripción Símbolo ISO Símbolos Instrucciones DE Referencia Scag POR Aprobados Dispositivos USE SóloRepuesto de Piezas 8 Sección Mantenimiento 7 SecciónAjustes 6 Sección Seguridad de Información 2 Sección Operación De Instrucciones 4 SecciónEspecificaciones 3 Sección General Información 1 SecciónAdvertencia Operadordel Manual

STC61V-25CV-FR, STC48V-26BS, STC48V26BS, STC61V-25CV, STC61V-23BV specifications

Scag Power Equipment has established itself as a leader in the outdoor power equipment industry, and its line of mowers, particularly the STC series, exemplifies premium engineering and cutting-edge technology. Among the standout models are the STC52V-23BV, STC52V-25CV-FR, STC52V-25CV, STC61V-23BV, and STC61V-25CV. Each model is designed to meet the diverse demands of commercial and residential landscaping, providing efficiency, performance, and durability.

The STC52V-23BV and the STC52V-25CV-FR are both equipped with powerful V-twin engines that deliver dependable performance under tough conditions. These engines are designed to provide high torque, enabling users to tackle tougher mowing tasks without sacrificing speed or efficiency. With a cutting deck width of 52 inches, the STC52V models offer excellent maneuverability while providing ample coverage for large lawns.

On the other hand, the STC61V-23BV and STC61V-25CV models feature an impressive 61-inch cutting deck, making them ideal for larger properties. The wider deck allows for more efficient mowing with fewer passes, ultimately saving time and reducing operator fatigue. Both models also boast V-twin engines, ensuring robust performance that can handle dense grass and uneven terrain with ease.

One of the significant characteristics of the STC series is Scag's innovative Velocity Plus cutting deck technology. This unique design enhances airflow beneath the deck, resulting in superior grass cutting and improved discharge. The deck's aerodynamic shape not only ensures a clean cut but also allows for better grass collection in conjunction with optional bagging systems.

Additionally, all STC models are built with operator comfort in mind. Ergonomically designed controls, spacious seating, and intuitive instrument panels enable operators to work efficiently without discomfort during extended periods. These mowers also come standard with heavy-duty frames and high-quality components that offer durability and long-lasting performance, even in the most demanding conditions.

Another noteworthy feature across the STC lineup is the ease of maintenance. Scag Power Equipment has designed these mowers with accessible components, making it easier for users to perform routine maintenance tasks. This focus on practicality ensures that owners can keep their equipment in optimum condition with minimal effort.

In conclusion, the Scag Power Equipment STC52V-23BV, STC52V-25CV-FR, STC52V-25CV, STC61V-23BV, and STC61V-25CV represent the pinnacle of performance, comfort, and durability in the commercial mower sector. With powerful engines, advanced cutting technology, and a focus on user experience, these mowers continue to set the standard for excellence in outdoor power equipment.