Scag Power Equipment STC61V-25CV-FR, STC61V-23BV, STC52V-23BV manual Roll-over protection system

Page 10

R

Section 2

2.5 Roll-over protection system

WARNING

Reduce speed when turning, operating on slopes, slick or wet surfaces. Allow extra distance to stop.

Stay off of slopes too steep for safe operation. To check a slope, attempt to back up it (with the cutter deck down). If the machine can not back up the slope without the wheels slipping, do not operate the machine on this slope. Under no circumstances should the machine be operated on slopes greater than 15 degrees.

DO NOT mow near drop-offs, ditches or embankments. The machine could suddenly roll over if a wheel goes over the edge or if the edge caves in.

Operate the machine smoothly, no sudden turns, starts or stops on a slope.

NEVER tow on slopes. The weight of the towed equipment may cause loss of traction and loss of control.

DO NOT permit untrained personnel to operate the machine.

Be cautious when loading and unloading onto trailers or trucks.

Use only a full width ramp.

Ramp angle should be no more than 15 degrees.

Back up the ramp and drive down forward.

This mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Do not mow on wet grass. Wet grass reduces traction and steering control.

Any or all parts of the Roll-Over Protection System MUST NOT be removed. Failure to adhere to this guideline could result in injury or death.

FOLDABLE Roll-over protection system (if equipped)

WARNING

Keep the roll bar in the raised and locked position and the seat belt securely fastened during operation. Failure to do so could cause serious injury or loss of life.

Lower the roll bar only when absolutely necessary.

WARNING

There is no roll-over protection when the roll bar is in the down position.

Lower the roll bar only when absolutely necessary.

Raise the roll bar as soon as clearance permits.

DO NOT wear the seat belt when the roll bar is in the down position.

ALWAYS wear seat belt when roll bar is in the up position.

Operate the machine smoothly, no sudden turns, starts or stops.

Check the area carefully before mowing for proper overhead clearance (i.e. branches, doorways, etc.).

DO NOT contact any overhead object with the roll bar.

1.To lower the roll bar, loosen the tension knob on both the left hand and right hand bar. See Figure 2-1.

6

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited Warranty Commercial Equipment Inside Back CoverDirection Reference General InformationIntroduction Servicing The Engine and Drive Train ComponentsSymbols Symbol DescriptionSignal Words Safety InformationBefore Operation considerations Operation Considerations Section Roll-over protection system Foldable Roll-over protection system if equippedFoldable Roll-Over Protection System Maintenance Considerations & storage Safety and Instructional Decals Install Belt COvER BeforeElectrical SpecificationsEngine TractorHydraulic System Weights and Dimensions 48V 52V 61VCutter Deck ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Initial RUN-IN ProceduresGround Travel and Steering Starting the EngineForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelAfter Operation Hillside OperationParking the Mower Removing Clogged MaterialMoving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Adjusting the Steering Levers Towing optional hitch accessoryTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Parking Brake Adjustment AdjustmentsTravel Adjustments Neutral Adjustment Tracking AdjustmentCutter Deck Adjustments Throttle Control and Choke AdjustmentsBelt Adjustment Belt AlignmentAdjustment ROD Lock NUT Cutter Deck Pitch Cutter Deck HeightPosition Custom-Cut Baffle Adjustment eARLY mODELS Custom-Cut Baffle AdjustmentPosition Custom-Cut Baffle Adjustment cURRENT pRODUCTION Position Custom-Cut Baffle Adjustment Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine Oil Engine Fuel SystemCleaning and/or Replacing Air Cleaner Element Engine Air CleanerReplacing In-Line Fuel Filter Elements Charging the Battery BatteryJump Starting Cutter Blades Blade ReplacementDrive Belts Blade InspectionTires BODY, DECK, and UpholsteryIllustrated Parts List Scag Approved Attachments and Accessories48V & 52V Cutter Decks Description 61V Cutter Deck 424367 Dust Shield 483210 Idler Pulley, 5 Dia Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 482619 Tire, 13 x 6.5-6 Smooth 483736 STC Fixed ROLL-OVER Protection System STC Fixed ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System Drive System Components 04019-04 Nut, Serr. Flange 3/8-16 04001-136 Engine & Attaching Parts Engine and Attaching Parts Steering Components Damper orange colored print Damper blue colored print Brake Components Brake Components 33 47 Fuel and Hydraulic System Electrical System Battery, 330CCA Not Available Through Scag BDP-10A Hydraulic Pump Assembly Housing Kit Install Belt COvER Before Operating Machine482166R STC 2008 RDP2 Electrical Schematic Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Precaución LlantasCuchilla la de Reemplazo .C Cuchilla la de Reemplazo 9-7 FiguraPara apropiada protección la lleve Siempre Cuchillas las de Afilado 8-7 FiguraSeguridad garantizar para Transmisión DE CorreasCorte DE Cuchillas Rajada o rota cuchilla una suelde nuncaGases producen ácido-plomo baterías Las Advertencia BateríaDel elemento del reemplazo y/o Limpieza .A Motor DEL Combustible DE SistemaCárter del aceite de nivel del Verificación .A Cárter del aceite de Cambio .BAceite de filtro del elemento del Cambio .C Hidráulico aceite de Cambio .B Hidráulico SistemaHidráulico aceite de nivel del Verificación .A Lubricación DE Grasa DE Conexiones Figura LA VEA Grasa DE Conexión DE Lubricación DE Tabla LubricaciónMantenimiento Recomendados Servicio DE Intervalos Mantenimiento DE TablaSección Posiciones De personalizado corte de deflector del AjusteCorte de plataforma la de Altura Corte Corte de plataforma la de InclinaciónCorte de plataforma la de Nivel DE Plataforma LA DE AjustesAjustes Estrangulación Aceleración DE Control Correa LA DE AlineaciónCorrea LA DE Ajuste Alineación de AjusteDesplazamiento DE Ajustes Neutral AjusteDirección De control de varilla la de Ajuste .3-6 Figura DE Freno DEL Ajuste AjustesFreno de Ajuste .1-6 Figura Solución Causa Condición Solución Causa Condición Continuación Fallas DE Solución De Franjas Vetas Corte de trayectoriasEntre cortar sin césped La en cortar sin céspedOpcional Enganche de accesorio Remolque Advertencia PlataformaAtascado Material DEL Retiro Detenido Motor EL CON Cortacésped DEL DesplazamientoCortacésped DEL Estacionamiento Cuesta UNA EN Operación Corte DE Cuchillas Plataforma DE Transmisión LA DE ConexiónPrecaución Dirección Y Terreno EL EN DesplazamientoMotor DEL Arranque Seguridad DE Bloqueo DE SistemaFigura combustible de cambio de Válvula Instrumentos Controles DE IdentificaciónProductividad Corte DE PlataformaEléctrico Sistema TractorSeguridad DE Y Instructivas Calcomanías Cuchillas las suelde NUNCAni enderece.cuchillas Almacenamiento Y Mantenimiento DE ConsideracionesRops del Bisagra 2-2 Figura Vuelco contra protección de plegable Sistema 1-2 FiguraVuelco Contra Protección DE Sistema Advertencia Operación DE ConsideracionesAdvertencia Señalización DE Palabras Operación LA a Previas ConsideracionesIntroducción Descripción Símbolo ISO Símbolos Instrucciones DE Referencia Scag POR Aprobados Dispositivos USE SóloMantenimiento 7 Sección Repuesto de Piezas 8 SecciónAjustes 6 Sección Seguridad de Información 2 Sección Operación De Instrucciones 4 SecciónEspecificaciones 3 Sección General Información 1 SecciónAdvertencia Operadordel Manual

STC61V-25CV-FR, STC48V-26BS, STC48V26BS, STC61V-25CV, STC61V-23BV specifications

Scag Power Equipment has established itself as a leader in the outdoor power equipment industry, and its line of mowers, particularly the STC series, exemplifies premium engineering and cutting-edge technology. Among the standout models are the STC52V-23BV, STC52V-25CV-FR, STC52V-25CV, STC61V-23BV, and STC61V-25CV. Each model is designed to meet the diverse demands of commercial and residential landscaping, providing efficiency, performance, and durability.

The STC52V-23BV and the STC52V-25CV-FR are both equipped with powerful V-twin engines that deliver dependable performance under tough conditions. These engines are designed to provide high torque, enabling users to tackle tougher mowing tasks without sacrificing speed or efficiency. With a cutting deck width of 52 inches, the STC52V models offer excellent maneuverability while providing ample coverage for large lawns.

On the other hand, the STC61V-23BV and STC61V-25CV models feature an impressive 61-inch cutting deck, making them ideal for larger properties. The wider deck allows for more efficient mowing with fewer passes, ultimately saving time and reducing operator fatigue. Both models also boast V-twin engines, ensuring robust performance that can handle dense grass and uneven terrain with ease.

One of the significant characteristics of the STC series is Scag's innovative Velocity Plus cutting deck technology. This unique design enhances airflow beneath the deck, resulting in superior grass cutting and improved discharge. The deck's aerodynamic shape not only ensures a clean cut but also allows for better grass collection in conjunction with optional bagging systems.

Additionally, all STC models are built with operator comfort in mind. Ergonomically designed controls, spacious seating, and intuitive instrument panels enable operators to work efficiently without discomfort during extended periods. These mowers also come standard with heavy-duty frames and high-quality components that offer durability and long-lasting performance, even in the most demanding conditions.

Another noteworthy feature across the STC lineup is the ease of maintenance. Scag Power Equipment has designed these mowers with accessible components, making it easier for users to perform routine maintenance tasks. This focus on practicality ensures that owners can keep their equipment in optimum condition with minimal effort.

In conclusion, the Scag Power Equipment STC52V-23BV, STC52V-25CV-FR, STC52V-25CV, STC61V-23BV, and STC61V-25CV represent the pinnacle of performance, comfort, and durability in the commercial mower sector. With powerful engines, advanced cutting technology, and a focus on user experience, these mowers continue to set the standard for excellence in outdoor power equipment.
Top Page Image Contents