Scag Power Equipment STC61V-23BV, STC52V-23BV, STC61V-25CV-FR, STC48V26BS Operation Considerations

Page 8

R

Section 2

7.If the operator(s) or mechanic(s) cannot read English or Spanish, it is the owner's responsibility to explain this material to them.

8.DO NOT wear loose fitting clothing. Loose clothing, jewelry or long hair could get tangled in moving parts. Do not operate the machine wearing shorts; always wear adequate protective clothing including long pants. Wearing safety glasses, safety shoes and a helmet is advisable and is required by some local ordinances and insurance regulations.

WARNING

Always wear hearing protection. Operating this machine over prolonged periods of time can cause loss of hearing.

9.Keep the machine and attachments in good operating condition. Keep all shields and safety devices in place. If a shield, safety device or decal is defective or damaged, repair or replace it before operating the machine.

WARNING

This machine is equipped with an interlock system intended to protect the operator and others from injury. This is accomplished by preventing the engine from starting unless the deck drive is disengaged, the parking brake is on, the steering control levers are in the neutral position and the operator is in the seat. The system shuts off the engine if the operator leaves the seat with the deck drive engaged and/or the steering control levers are not in the neutral position and the parking brake is not engaged. Never operate equipment with the interlock system disconnected or malfunctioning.

10.Be sure the interlock switches are functioning correctly.

11.Fuel is flammable; handle it with care. Fill the fuel tank outdoors. Never fill it indoors. Use a funnel or spout to prevent spillage. Clean up any spillage before starting the engine.

12.DO NOT add fuel to a running or hot engine. Allow the engine to cool for several minutes before adding fuel. Never fuel indoors or inside enclosed trailers.

13.Keep flammable objects (cigarettes, matches, etc.), open flames and sparks away from the fuel tank and fuel container. Use only approved containers.

14.Equipment must comply with the latest requirements per SAE J137 and/or ANSI/ASAE S279 when driven on public roads.

- note -

If the mower is driven on public roads, it must comply with state and local ordinances as well as SAE J137 and/or ANSI / ASAE S279 requirements. Contact your local authorities for regulations and equipment requirements.

15.Do not operate without the side discharge chute installed and in the down position or with an optional grass catcher or mulch plate completely installed.

16.Check the blade mounting bolts at frequent intervals for proper tightness.

17.Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before starting the machine.

2.4 Operation Considerations

1.Know the function of all controls and how to stop quickly.

WARNING

DO NOT operate on steep slopes.To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. Under no circumstances should the machine be operated on slopes greater than 15 degrees. ALWAYS FOLLOW OSHA APPROVED OPERATION.

2.Reduce speed and exercise extreme caution on slopes and in sharp turns to prevent tipping or loss of control. Be especially cautious when changing directions on slopes.

4

Page 7 Page 9
Image 8
Page 7 Page 9
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited Warranty Commercial Equipment Inside Back CoverGeneral Information IntroductionDirection Reference Servicing The Engine and Drive Train ComponentsSymbols Symbol DescriptionBefore Operation considerations Safety InformationSignal Words Operation Considerations Section Roll-over protection system Foldable Roll-over protection system if equippedFoldable Roll-Over Protection System Maintenance Considerations & storage Safety and Instructional Decals Install Belt COvER BeforeSpecifications EngineElectrical TractorWeights and Dimensions 48V 52V 61V Cutter DeckHydraulic System ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Initial RUN-IN ProceduresForward Travel Starting the EngineGround Travel and Steering Engaging the Deck Drive Cutter Blades Reverse TravelHillside Operation Parking the MowerAfter Operation Removing Clogged MaterialRecommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Adjusting the Steering Levers Towing optional hitch accessoryTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Travel Adjustments AdjustmentsParking Brake Adjustment Neutral Adjustment Tracking AdjustmentThrottle Control and Choke Adjustments Belt AdjustmentCutter Deck Adjustments Belt AlignmentAdjustment ROD Lock NUT Cutter Deck Pitch Cutter Deck HeightPosition Custom-Cut Baffle Adjustment cURRENT pRODUCTION Custom-Cut Baffle AdjustmentPosition Custom-Cut Baffle Adjustment eARLY mODELS Position Custom-Cut Baffle Adjustment Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine Oil Engine Fuel SystemReplacing In-Line Fuel Filter Elements Engine Air CleanerCleaning and/or Replacing Air Cleaner Element Jump Starting BatteryCharging the Battery Blade Replacement Drive BeltsCutter Blades Blade InspectionTires BODY, DECK, and UpholsteryIllustrated Parts List Scag Approved Attachments and Accessories48V & 52V Cutter Decks Description 61V Cutter Deck 424367 Dust Shield 483210 Idler Pulley, 5 Dia Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 482619 Tire, 13 x 6.5-6 Smooth 483736 STC Fixed ROLL-OVER Protection System STC Fixed ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System Drive System Components 04019-04 Nut, Serr. Flange 3/8-16 04001-136 Engine & Attaching Parts Engine and Attaching Parts Steering Components Damper orange colored print Damper blue colored print Brake Components Brake Components 33 47 Fuel and Hydraulic System Electrical System Battery, 330CCA Not Available Through Scag BDP-10A Hydraulic Pump Assembly Housing Kit Install Belt COvER Before Operating Machine482166R STC 2008 RDP2 Electrical Schematic Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Precaución LlantasCuchilla la de Reemplazo 9-7 Figura Para apropiada protección la lleve SiempreCuchilla la de Reemplazo .C Cuchillas las de Afilado 8-7 FiguraTransmisión DE Correas Corte DE CuchillasSeguridad garantizar para Rajada o rota cuchilla una suelde nuncaDel elemento del reemplazo y/o Limpieza .A BateríaGases producen ácido-plomo baterías Las Advertencia Motor DEL Combustible DE SistemaAceite de filtro del elemento del Cambio .C Cárter del aceite de Cambio .BCárter del aceite de nivel del Verificación .A Hidráulico aceite de nivel del Verificación .A Hidráulico SistemaHidráulico aceite de Cambio .B Lubricación DE Grasa DE Conexiones Figura LA VEA Grasa DE Conexión DE Lubricación DE Tabla LubricaciónMantenimiento Recomendados Servicio DE Intervalos Mantenimiento DE TablaSección Posiciones De personalizado corte de deflector del AjusteCorte de plataforma la de Altura Corte de plataforma la de Inclinación Corte de plataforma la de NivelCorte DE Plataforma LA DE AjustesCorrea LA DE Alineación Correa LA DE AjusteAjustes Estrangulación Aceleración DE Control Alineación de AjusteDirección De control de varilla la de Ajuste .3-6 Figura Neutral AjusteDesplazamiento DE Ajustes Freno de Ajuste .1-6 Figura AjustesDE Freno DEL Ajuste Solución Causa Condición Solución Causa Condición Continuación Fallas DE Solución Corte de trayectorias Entre cortar sin céspedDe Franjas Vetas La en cortar sin céspedOpcional Enganche de accesorio Remolque Advertencia PlataformaCortacésped DEL Estacionamiento Detenido Motor EL CON Cortacésped DEL DesplazamientoAtascado Material DEL Retiro Cuesta UNA EN Operación Corte DE Cuchillas Plataforma DE Transmisión LA DE ConexiónPrecaución Dirección Y Terreno EL EN DesplazamientoMotor DEL Arranque Seguridad DE Bloqueo DE SistemaFigura combustible de cambio de Válvula Instrumentos Controles DE IdentificaciónProductividad Corte DE PlataformaEléctrico Sistema TractorSeguridad DE Y Instructivas Calcomanías Cuchillas las suelde NUNCAni enderece.cuchillas Almacenamiento Y Mantenimiento DE ConsideracionesRops del Bisagra 2-2 Figura Vuelco contra protección de plegable Sistema 1-2 FiguraVuelco Contra Protección DE Sistema Advertencia Operación DE ConsideracionesAdvertencia Introducción Operación LA a Previas ConsideracionesSeñalización DE Palabras Descripción Símbolo ISO Símbolos Instrucciones DE Referencia Scag POR Aprobados Dispositivos USE SóloAjustes 6 Sección Repuesto de Piezas 8 SecciónMantenimiento 7 Sección Operación De Instrucciones 4 Sección Especificaciones 3 SecciónSeguridad de Información 2 Sección General Información 1 SecciónAdvertencia Operadordel Manual

STC61V-25CV-FR, STC48V-26BS, STC48V26BS, STC61V-25CV, STC61V-23BV specifications

Scag Power Equipment has established itself as a leader in the outdoor power equipment industry, and its line of mowers, particularly the STC series, exemplifies premium engineering and cutting-edge technology. Among the standout models are the STC52V-23BV, STC52V-25CV-FR, STC52V-25CV, STC61V-23BV, and STC61V-25CV. Each model is designed to meet the diverse demands of commercial and residential landscaping, providing efficiency, performance, and durability.

The STC52V-23BV and the STC52V-25CV-FR are both equipped with powerful V-twin engines that deliver dependable performance under tough conditions. These engines are designed to provide high torque, enabling users to tackle tougher mowing tasks without sacrificing speed or efficiency. With a cutting deck width of 52 inches, the STC52V models offer excellent maneuverability while providing ample coverage for large lawns.

On the other hand, the STC61V-23BV and STC61V-25CV models feature an impressive 61-inch cutting deck, making them ideal for larger properties. The wider deck allows for more efficient mowing with fewer passes, ultimately saving time and reducing operator fatigue. Both models also boast V-twin engines, ensuring robust performance that can handle dense grass and uneven terrain with ease.

One of the significant characteristics of the STC series is Scag's innovative Velocity Plus cutting deck technology. This unique design enhances airflow beneath the deck, resulting in superior grass cutting and improved discharge. The deck's aerodynamic shape not only ensures a clean cut but also allows for better grass collection in conjunction with optional bagging systems.

Additionally, all STC models are built with operator comfort in mind. Ergonomically designed controls, spacious seating, and intuitive instrument panels enable operators to work efficiently without discomfort during extended periods. These mowers also come standard with heavy-duty frames and high-quality components that offer durability and long-lasting performance, even in the most demanding conditions.

Another noteworthy feature across the STC lineup is the ease of maintenance. Scag Power Equipment has designed these mowers with accessible components, making it easier for users to perform routine maintenance tasks. This focus on practicality ensures that owners can keep their equipment in optimum condition with minimal effort.

In conclusion, the Scag Power Equipment STC52V-23BV, STC52V-25CV-FR, STC52V-25CV, STC61V-23BV, and STC61V-25CV represent the pinnacle of performance, comfort, and durability in the commercial mower sector. With powerful engines, advanced cutting technology, and a focus on user experience, these mowers continue to set the standard for excellence in outdoor power equipment.
Top Page Image Contents