Scag Power Equipment STT-31BSD manual Engine Fuel System, Engine AIR Cleaner, Battery

Page 37

Section 7

7.5 ENGINE FUEL SYSTEM

To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.

Fuel Filter

(with hose clamps above and below)

STT99FF-1

Figure 7-5 Fuel Filter

A. Filling the Fuel Tank

Fill the fuel tank at the beginning of each operating day to within one inch below the filler neck. Do not overfill. Use clean, fresh diesel fuel with a minimum cetane rating of 40.

B. Replacing In-Line Fuel Filter Element

-NOTE-

The fuel filter is located below the hydraulic tank. Figure 7-5 is for illustration purposes only.

The in-line fuel filter (Figure 7-5) should be replaced after every 500 hours of operation or annually, whichever occurs first.

1.Close the shut-off valve. Remove the two clamps securing the fuel filter to the fuel hose. Remove the fuel filter.

2.Install a new fuel filter. Be sure it is installed in the proper direction. Secure to the fuel hose using the two clamps.

7.6 ENGINE AIR CLEANER

A. Cleaning and/or Replacing Air Cleaner Element

For any air cleaner, the operating environment dictates the air cleaner service periods. To make it convenient for you we have installed an "Air Cleaner Indicator" which is located just behind the air filter. The indicator window will turn red when it is time to service the air filter. Do not service the filter unless this indicator is red.

-NOTE-

In extremely dusty conditions it may be necessary to check the indicator daily to prevent engine damage.

1.Snap open the two clips securing the air cleaner cover to the air cleaner box. Remove the air cleaner cover, clean the duck bill vent of any dust and set the cover aside.

2.Remove the air cleaner element and inspect.

3.Clean or replace the element as recommended by the engine manufacturer.

4.Replace the air filter cover and be sure to snap the two clips closed.

5.Reset the air cleaner indicator by pushing the button on the end of the indicator. The indicator window should return to clear.

7.7 BATTERY

WARNING:

Lead-acid batteries produce flammable and explosive gases. To avoid personal injury when checking, testing or charging batteries, DO NOT use smoking materials near batteries. Keep arcs, sparks and flames away from batteries. Provide proper ventilation and wear safety glasses.

33

Image 37
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Introduction General InformationDirection Reference Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Signal Words Safety InformationBefore Operation Considerations Operation Considerations Before Operation Considerations ContdRoll Over Protection System Operation Considerations ContdSeat Belt Inspection STT-BSD With Roll Over Protection System Maintenance Considerations & StorageSafety and Instructional Decals Engine Deck EngineDrive System Additional Specifications SpecificationsApproximate Dimensions ProductivityControls and Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemGround Travel and Steering Starting the EngineForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelParking the Mower Hillside OperationAfter Operation Moving Mower with Engine Stopped Removing Clogged MaterialRecommendations for Mowing Deck Release Lever Adjusting Cutting HeightCondition Cause Cure Troubleshooting Cutting ConditionsScalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause CureGround Troubleshooting ContdParking Brake Adjustment AdjustmentsTravel Adjustments RH Steering Control Rod Adjustment Neutral AdjustmentBelt Adjustment Tracking AdjustmentThrottle Control Belt AlignmentCutter Deck Level Cutter Deck AdjustmentsCutter Deck Pitch Cutter Deck Height Custom-Cut Baffle AdjustmentCustom-Cut Baffle Maintenance Chart Recommended Service Intervals MaintenanceLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Checking Hydraulic Oil Level Hydraulic SystemChanging Hydraulic Oil Changing Hydraulic Oil Filter Element Engine OILChecking Engine Crankcase Oil Level Changing Engine Crankcase OilBattery Engine AIR CleanerEngine Fuel System Jump Starting Charging the BatteryDrive Belts Blade ReplacementCutter Blades Blade InspectionCutter Deck Gearbox TiresChecking Lubricant Level Changing Lubricant Cleaning the Radiator Debris ScreenCooling System Checking Coolant LevelBODY, DECK, and Upholstery Checking The Fan Belt TensionPage 61A, 72A Cutter Decks Ref. Part Description Cutter Deck Controls Part Description Sheet Metal Components Wheel Assy Inc.items 20, 42, 43, 54 STT Roll Over Protection System Ref. Part No. No. Description Deck Drive Components Ref. Part Description Radiator & Engine Brackets Radiator & Engine Brackets Brake and Steering Components Part Description Fuel and Hydraulic System Ref. Part Description Electrical System 35 483072 Hour Meter HYDRAULICHYDRAULICPUMPPUMPASSEMBLYASSEMBLY- BDP-21L Hydraulic Pump Assembly BDP-21L Wire HARNESS, STT 31BSD Part Number Heavy-Duty 482367 48825 481937 48314 Limited Warranty Commercial Equipment