Scag Power Equipment STT-31BSD manual Reverse Travel, Engaging the Deck Drive Cutter Blades

Page 19

Section 4

To stop the forward travel, pull the steering control levers back to the neutral position.

To steer the mower left while traveling forward, pull the left steering lever back. The further the lever is pulled back, the quicker the mower will turn left.

To steer the mower right while traveling forward, pull the right steering control lever back. The further the lever is pulled back, the quicker the mower will turn right.

-NOTE-

Smooth operation of the steering levers will produce smooth mower operation. While learning the operation of the steering controls, keep the travel speed low.

-IMPORTANT-

Do not travel forward over a curb. The mower will hang up on the curb. Raise the deck and travel backwards over the curb at a 45 degree angle. (see section 4.13 on Page 16 for cutter deck raising instructions)

Reverse Travel

CAUTION:

Disengage power to the mower before backing up. Do not mow in reverse unless absolutely necessary and then only after observation of the entire area behind the mower.

-NOTE-

The mower may not travel straight in reverse. Slight adjustments may need to be made using the steering controls.

To steer left while traveling in reverse, allow the left steering control lever to move forward. The further the control is allowed to move forward, the quicker the mower will turn left.

To steer right while traveling in reverse, allow the right steering control lever to move forward. The further the control is allowed to move forward, the quicker the mower will turn right.

To stop the reverse travel, allow the steering control levers to return to the neutral position. If the mower is to be parked, engage the parking brake.

4.6ENGAGING THE DECK DRIVE (CUTTER BLADES)

1.Set the throttle at about 3/4 speed. Do not attempt to engage the deck drive at high speed as this shortens the electric clutch life — use only moderate engine speed when engaging the deck drive.

2.Engage the deck drive by pulling out on the yellow switch, located on the instrument panel, (Figure 4-3) to the engage position.

CAUTION:

Before backing up, observe the rear for persons and obstructions. Clear the area before backing up. Possible injury or property damage could occur.

PULL UP TO ENGAGE

PUSH DOWN TO DISENGAGE

STT99CES

To travel in reverse, pull both handles back. Keep the travel speed low while traveling in reverse.

15

Figure 4-3 Cutter Engage Switch

-NOTE-

A squealing noise may be heard when engaging or disengaging the deck drive. It is caused by the electric clutch plates meshing as the mower comes up to speed.

Image 19
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Servicing the Engine and Drive Train Components General InformationIntroduction Direction ReferenceISO Symbols CE Mark Fast Slow Signal Words Safety InformationBefore Operation Considerations Operation Considerations Before Operation Considerations ContdRoll Over Protection System Operation Considerations ContdSeat Belt Inspection STT-BSD With Roll Over Protection System Maintenance Considerations & StorageSafety and Instructional Decals Engine Deck EngineDrive System Productivity SpecificationsAdditional Specifications Approximate DimensionsControls and Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemGround Travel and Steering Starting the EngineForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelParking the Mower Hillside OperationAfter Operation Moving Mower with Engine Stopped Removing Clogged MaterialRecommendations for Mowing Deck Release Lever Adjusting Cutting HeightCondition Cause Cure Troubleshooting Cutting ConditionsScalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause CureGround Troubleshooting ContdParking Brake Adjustment AdjustmentsTravel Adjustments RH Steering Control Rod Adjustment Neutral AdjustmentBelt Alignment Tracking AdjustmentBelt Adjustment Throttle ControlCutter Deck Level Cutter Deck AdjustmentsCutter Deck Pitch Cutter Deck Height Custom-Cut Baffle AdjustmentCustom-Cut Baffle Maintenance Chart Recommended Service Intervals MaintenanceLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Checking Hydraulic Oil Level Hydraulic SystemChanging Hydraulic Oil Changing Engine Crankcase Oil Engine OILChanging Hydraulic Oil Filter Element Checking Engine Crankcase Oil LevelBattery Engine AIR CleanerEngine Fuel System Jump Starting Charging the BatteryBlade Inspection Blade ReplacementDrive Belts Cutter BladesCutter Deck Gearbox TiresChecking Lubricant Level Checking Coolant Level Cleaning the Radiator Debris ScreenChanging Lubricant Cooling SystemBODY, DECK, and Upholstery Checking The Fan Belt TensionPage 61A, 72A Cutter Decks Ref. Part Description Cutter Deck Controls Part Description Sheet Metal Components Wheel Assy Inc.items 20, 42, 43, 54 STT Roll Over Protection System Ref. Part No. No. Description Deck Drive Components Ref. Part Description Radiator & Engine Brackets Radiator & Engine Brackets Brake and Steering Components Part Description Fuel and Hydraulic System Ref. Part Description Electrical System 35 483072 Hour Meter HYDRAULICHYDRAULICPUMPPUMPASSEMBLYASSEMBLY- BDP-21L Hydraulic Pump Assembly BDP-21L Wire HARNESS, STT 31BSD Part Number Heavy-Duty 482367 48825 481937 48314 Limited Warranty Commercial Equipment