Scag Power Equipment STT-31BSD Safety Information, Signal Words, Before Operation Considerations

Page 8

Section 2

SAFETY INFORMATION

2.1 INTRODUCTION

Your mower is only as safe as the operator. Carelessness or operator error may result in serious bodily injury or death. Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance and storage of the equipment. Make sure every operator is properly trained and thoroughly familiar with all of the controls before operating the mower. The owner/user can prevent and is responsible for accidents or injuries occuring to themselves, other people or property.

READ THIS OPERATOR’S MANUAL BEFORE ATTEMPTING TO START YOUR MOWER.

A replacement manual is available from your authorized Scag Service Dealer or by contacting Scag Power Equipment, Service Department at P.O. Box 152, Mayville, WI 53050 or via the Internet at www.scag.com. The manual for your machine can be downloaded by using the model and serial number or use the contact form to make your request. Please indicate the complete model and serial number of your Scag product when requesting replacement manuals.

2.2 SIGNAL WORDS

This symbol means “Attention! Become Alert! Your

Safety is Involved!" The symbol is used with the following signal words to attract your attention to safety messages found on the decals on the machine and throughout this manual. The message that follows the symbol contains important information about safety. To avoid injury and possible death, carefully read the message! Be sure to fully understand the causes of possible injury or death.

Signal Word:

The signal word “DANGER” denotes that an extremely hazardous situation exists on or near the machine that could result in high probability of death or irrepairable injury if proper precautions are not taken.

WARNING:

The signal word “WARNING” denotes that a hazard exists on or near the machine that can result in injury or death if proper precautions are not taken.

CAUTION:

The signal word “CAUTION” is a reminder of safety practices on or near the machine that could result in personal injury if proper precautions are not taken.

Your safety and the safety of others depends significantly upon your knowledge and understanding of all correct operating practices and procedures of this machine.

2.3BEFORE OPERATION CONSIDERATIONS

1.NEVER allow children to operate this riding mower. Do not allow adults to operate this machine without proper instructions.

2.DO NOT mow when children and/or others are present. Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. Be alert and turn machine off if a child enters the area.

3.Clear the area to be mowed of objects that could be picked up and thrown by the cutter blades.

4.DO NOT carry passengers.

It is a distinctive word found on the safety decals on the machine and throughout this manual that alerts the viewer to the existence and relative degree of the hazard.

5.DO NOT operate the machine under the influence of alcohol or drugs.

4

Image 8
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd General Information IntroductionDirection Reference Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Before Operation Considerations Safety InformationSignal Words Before Operation Considerations Contd Operation ConsiderationsOperation Considerations Contd Roll Over Protection SystemSeat Belt Inspection Maintenance Considerations & Storage STT-BSD With Roll Over Protection SystemSafety and Instructional Decals Drive System EngineEngine Deck Specifications Additional SpecificationsApproximate Dimensions ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Dump Valve ControlForward Travel Starting the EngineGround Travel and Steering Reverse Travel Engaging the Deck Drive Cutter BladesAfter Operation Hillside OperationParking the Mower Recommendations for Mowing Removing Clogged MaterialMoving Mower with Engine Stopped Adjusting Cutting Height Deck Release LeverTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Scalloped Cut, or Rough ContourTroubleshooting Contd GroundTravel Adjustments AdjustmentsParking Brake Adjustment Neutral Adjustment RH Steering Control Rod AdjustmentTracking Adjustment Belt AdjustmentThrottle Control Belt AlignmentCutter Deck Pitch Cutter Deck AdjustmentsCutter Deck Level Custom-Cut Baffle Adjustment Cutter Deck HeightCustom-Cut Baffle Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd Lubrication Grease Fitting Lubrication Chart see FigureLubrication Fitting Points Changing Hydraulic Oil Hydraulic SystemChecking Hydraulic Oil Level Engine OIL Changing Hydraulic Oil Filter ElementChecking Engine Crankcase Oil Level Changing Engine Crankcase OilEngine Fuel System Engine AIR CleanerBattery Charging the Battery Jump StartingBlade Replacement Drive BeltsCutter Blades Blade InspectionChecking Lubricant Level TiresCutter Deck Gearbox Cleaning the Radiator Debris Screen Changing LubricantCooling System Checking Coolant LevelChecking The Fan Belt Tension BODY, DECK, and UpholsteryPage 61A, 72A Cutter Decks Ref. Part Description Cutter Deck Controls Part Description Sheet Metal Components Wheel Assy Inc.items 20, 42, 43, 54 STT Roll Over Protection System Ref. Part No. No. Description Deck Drive Components Ref. Part Description Radiator & Engine Brackets Radiator & Engine Brackets Brake and Steering Components Part Description Fuel and Hydraulic System Ref. Part Description Electrical System 35 483072 Hour Meter HYDRAULICHYDRAULICPUMPPUMPASSEMBLYASSEMBLY- BDP-21L Hydraulic Pump Assembly BDP-21L Wire HARNESS, STT 31BSD Part Number Heavy-Duty 482367 48825 481937 48314 Limited Warranty Commercial Equipment