Scag Power Equipment STT-31BSD manual Before Operation Considerations Contd

Page 9

Section 2

2.3BEFORE OPERATION CONSIDERATIONS (CONT'D)

6.If the operator(s) or mechanic(s) cannot read English or Spanish, it is the owner's responsibility to explain this material to them.

7.DO NOT wear loose fitting clothing. Loose clothing, jewelry or long hair could get tangled in moving parts. Do not operate the machine wearing shorts; always wear adequate protective clothing including long pants. Wearing safety glasses, safety shoes and a helmet is advisable and is required by some local ordinances and insurance regulations.

8.Operator hearing protection is recommended, particularly for continuous operation of the mower. Wear suitable hearing protection. Prolonged exposure to loud noise can cause hearing impairment or loss.

9.Keep the machine and attachments in good operating condition. Keep all shields and safety devices in place. If a shield, safety device or decal is defective or damaged, repair or replace it before operating the machine.

WARNING:

This machine is equipped with an interlock system intended to protect the operator and others from injury. This is accomplished by preventing the engine from starting unless the deck drive is disengaged, the parking brake is on, the steering control levers are in the neutral position and the operator is in the seat. The system shuts off the engine if the operator leaves the seat with the deck drive engaged and/or the steering control levers are not in the neutral postion and the parking brake is not engaged. Never operate equipment with the interlock system disconnected or malfunctioning.

10.Be sure the interlock switches are functioning correctly.

11.Fuel is flammable; handle it with care. Fill the fuel tank outdoors. Never fill it indoors. Use a funnel or spout to prevent spillage. Clean up any spillage before starting the engine.

12.DO NOT add fuel to a running or hot engine. Allow the engine to cool for several minutes before adding fuel.

13.Keep flammable objects (cigarettes, matches, etc.), open flames and sparks away from the fuel tank and fuel container.

14.Equipment must comply with the latest requirements per SAE J137 and/or ANSI/ASAE S279 when driven on public roads.

-NOTE-

If the mower is driven on public roads, it must comply with state and local ordinances as well as SAE J137 and/or ANSI / ASAE S279 requirements. Contact your local authorities for regulations and equipment requirements.

15.DO NOT operate without the side discharge chute installed and in the down position or with an optional grass catcher or mulch plate completely installed.

16.Check the blade mounting bolts at frequent intervals for proper tightness.

17.Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before starting the machine.

2.4 OPERATION CONSIDERATIONS

1.Know the function of all controls and how to stop quickly.

2.Reduce speed and exercise extreme caution on slopes and in sharp turns to prevent tipping or loss of control. Be especially cautious when changing directions on slopes.

WARNING:

DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. ALWAYS FOLLOW OSHA APPROVED OPERATION.

5

Image 9
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Introduction General InformationDirection Reference Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Safety Information Signal WordsBefore Operation Considerations Operation Considerations Before Operation Considerations ContdRoll Over Protection System Operation Considerations ContdSeat Belt Inspection STT-BSD With Roll Over Protection System Maintenance Considerations & StorageSafety and Instructional Decals Engine Engine DeckDrive System Additional Specifications SpecificationsApproximate Dimensions ProductivityControls and Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemStarting the Engine Ground Travel and SteeringForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelHillside Operation Parking the MowerAfter Operation Removing Clogged Material Moving Mower with Engine StoppedRecommendations for Mowing Deck Release Lever Adjusting Cutting HeightCondition Cause Cure Troubleshooting Cutting ConditionsScalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause CureGround Troubleshooting ContdAdjustments Parking Brake AdjustmentTravel Adjustments RH Steering Control Rod Adjustment Neutral AdjustmentBelt Adjustment Tracking AdjustmentThrottle Control Belt AlignmentCutter Deck Adjustments Cutter Deck LevelCutter Deck Pitch Cutter Deck Height Custom-Cut Baffle AdjustmentCustom-Cut Baffle Maintenance Chart Recommended Service Intervals MaintenanceLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Hydraulic System Checking Hydraulic Oil LevelChanging Hydraulic Oil Changing Hydraulic Oil Filter Element Engine OILChecking Engine Crankcase Oil Level Changing Engine Crankcase OilEngine AIR Cleaner BatteryEngine Fuel System Jump Starting Charging the BatteryDrive Belts Blade ReplacementCutter Blades Blade InspectionTires Cutter Deck GearboxChecking Lubricant Level Changing Lubricant Cleaning the Radiator Debris ScreenCooling System Checking Coolant LevelBODY, DECK, and Upholstery Checking The Fan Belt TensionPage 61A, 72A Cutter Decks Ref. Part Description Cutter Deck Controls Part Description Sheet Metal Components Wheel Assy Inc.items 20, 42, 43, 54 STT Roll Over Protection System Ref. Part No. No. Description Deck Drive Components Ref. Part Description Radiator & Engine Brackets Radiator & Engine Brackets Brake and Steering Components Part Description Fuel and Hydraulic System Ref. Part Description Electrical System 35 483072 Hour Meter HYDRAULICHYDRAULICPUMPPUMPASSEMBLYASSEMBLY- BDP-21L Hydraulic Pump Assembly BDP-21L Wire HARNESS, STT 31BSD Part Number Heavy-Duty 482367 48825 481937 48314 Limited Warranty Commercial Equipment