Scag Power Equipment STT-31BSD manual Checking The Fan Belt Tension, BODY, DECK, and Upholstery

Page 42

Section 7

-NOTE-

Check the radiator for excessive debris and clean with compressed air. Never spray a hot engine with water, use only compressed air to remove debris.

3. Re-install the debris screen to the radiator.

C. Checking The Fan Belt Tension

Periodically check the fan belt tension. The belt should deflect 1/2" with 10 pounds of pressure. See your Scag dealer if the belt is in need of adjustment or replacement.

7.13 BODY, DECK, AND UPHOLSTERY

CAUTION:

Do not wash any portion of the equipment while it is hot. Do not wash the engine; use compressed air.

1.After each use, wash the mower and cutter deck. Use cold water and automotive cleaners. Do not use pressure cleaners.

2.Do not spray electrical components.

3.Use a mild soap solution or a vinyl/rubber cleaner to clean the seat.

4.Repair damaged metal surfaces using Scag touch-up paint available from your authorized Scag dealer. Wax the mower for maximum paint protection.

38

Image 42
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Direction Reference General InformationIntroduction Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Safety Information Signal WordsBefore Operation Considerations Before Operation Considerations Contd Operation ConsiderationsOperation Considerations Contd Roll Over Protection SystemSeat Belt Inspection Maintenance Considerations & Storage STT-BSD With Roll Over Protection SystemSafety and Instructional Decals Engine Engine DeckDrive System Approximate Dimensions SpecificationsAdditional Specifications ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Dump Valve ControlStarting the Engine Ground Travel and SteeringForward Travel Reverse Travel Engaging the Deck Drive Cutter BladesHillside Operation Parking the MowerAfter Operation Removing Clogged Material Moving Mower with Engine StoppedRecommendations for Mowing Adjusting Cutting Height Deck Release LeverTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Scalloped Cut, or Rough ContourTroubleshooting Contd GroundAdjustments Parking Brake AdjustmentTravel Adjustments Neutral Adjustment RH Steering Control Rod AdjustmentThrottle Control Tracking AdjustmentBelt Adjustment Belt AlignmentCutter Deck Adjustments Cutter Deck LevelCutter Deck Pitch Custom-Cut Baffle Adjustment Cutter Deck HeightCustom-Cut Baffle Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd Lubrication Grease Fitting Lubrication Chart see FigureLubrication Fitting Points Hydraulic System Checking Hydraulic Oil LevelChanging Hydraulic Oil Checking Engine Crankcase Oil Level Engine OILChanging Hydraulic Oil Filter Element Changing Engine Crankcase OilEngine AIR Cleaner BatteryEngine Fuel System Charging the Battery Jump StartingCutter Blades Blade ReplacementDrive Belts Blade InspectionTires Cutter Deck GearboxChecking Lubricant Level Cooling System Cleaning the Radiator Debris ScreenChanging Lubricant Checking Coolant LevelChecking The Fan Belt Tension BODY, DECK, and UpholsteryPage 61A, 72A Cutter Decks Ref. Part Description Cutter Deck Controls Part Description Sheet Metal Components Wheel Assy Inc.items 20, 42, 43, 54 STT Roll Over Protection System Ref. Part No. No. Description Deck Drive Components Ref. Part Description Radiator & Engine Brackets Radiator & Engine Brackets Brake and Steering Components Part Description Fuel and Hydraulic System Ref. Part Description Electrical System 35 483072 Hour Meter HYDRAULICHYDRAULICPUMPPUMPASSEMBLYASSEMBLY- BDP-21L Hydraulic Pump Assembly BDP-21L Wire HARNESS, STT 31BSD Part Number Heavy-Duty 482367 48825 481937 48314 Limited Warranty Commercial Equipment