Scag Power Equipment SVR36A-20FX, SVR52V-26FX, SVR48V-24FX manual Safety Information, Signal Words

Page 7

Section 2

R

SAFETY INFORMATION

2.1 Introduction

Your mower is only as safe as the operator. Carelessness or operator error may result in serious bodily injury or death. Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance and storage of the equipment. Make sure every operator is properly trained and thoroughly familiar with all of the controls before operating the mower. The owner/user can prevent and is responsible for accidents or injuries occurring to themselves, other people or property.

READ THIS OPERATOR’S MANUAL BEFORE ATTEMPTING TO START YOUR MOWER.

A replacement manual is available from your authorized Scag Service Dealer or by contacting Scag Power Equipment, Service Department at P.O. Box 152, Mayville, WI 53050 or contact us via the Internet at www.scag.com. The manual for this machine can be downloaded by using the model and serial number or use the contact form to make your request. Please indicate the complete model and serial number of your Scag product when requesting replacement manuals.

2.2 Signal Words

Danger

The signal word “DANGER” denotes that an extremely hazardous situation exists on or near the machine that could result in high probability of death or irreparable injury if proper precautions are not taken.

Warning

The signal word “WARNING” denotes that a hazard exists on or near the machine that can result in injury or death if proper precautions are not taken.

Caution

The signal word “CAUTION” is a reminder of safety practices on or near the machine that could result in personal injury if proper precautions are not taken.

Your safety and the safety of others depends significantly upon your knowledge and understanding of all correct operating practices and procedures of this machine.

This symbol means “Attention! Become Alert! Your

Safety is Involved!" The symbol is used with the following signal words to attract your attention to safety messages found on the decals on the machine and throughout this manual. The message that follows the symbol contains important information about safety. To avoid injury and possible death, carefully read the message! Be sure to fully understand the causes of possible injury or death.

Signal Word:

It is a distinctive word found on the safety decals on the machine and throughout this manual that alerts the viewer to the existence and relative degree of the hazard.

2.3Before Operation considerations

1.NEVER allow children to operate this mower. Do not allow adults to operate this machine without proper instructions.

2.Do not mow when children and/or others are present. Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. Be alert and turn machine off if a child enters the area.

3.DO NOT allow children to ride or play on the machine, it is not a toy.

4.Clear the area to be mowed of objects that could be picked up and thrown by the cutter blades.

5.DO NOT carry passengers.

6.DO NOT operate the machine under the influence of alcohol or drugs.

3

Image 7
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Following Section Limited Warranty Commercial EquipmentServicing The Engine And Drive Train Components General InformationIntroduction Direction ReferenceSymbol Description SymbolsSignal Words Safety InformationBefore Operation considerations Section Front Tie Down Points Using a spark arrestor Maintenance Considerations & storage483407 483406 482291 Safety and Instructional DecalsEngine Deck SpecificationsEngine ElectricalProductivity Weights and Dimensions SVR-36a SvR-48v SVR-52vControls and Instrument Identification Operating InstructionsSafety Interlock System Forward Travel Ground Travel and SteeringReverse Travel Forward / Reverse Controls Engaging the Deck Drive Cutter BladesParking the Mower Hillside Operation After OperationRemoving Clogged Material Moving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Condition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Parking brake adjustment AdjustmentsTravel adjustment Tracking adjustment Neutral adjustmentBelt Alignment Throttle Control and Choke AdjustmentsBelt Adjustments Cutter deck adjustmentsCutter deck pitch Cutter deck levelCutter deck height Cutter Deck Height AdjustmentCustom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment Mounting Slot Selected FrONT Weight Adjustment Electric clutch adjustment11. Front Weight Adjustment Operator Cushion adjustment12. Operator Cushion Adjustment Maintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Checking Hydraulic Oil Level Hydraulic SystemChanging Hydraulic Oil Changing Engine Oil Filter Engine OilChanging Engine Crankcase Oil Changing Hydraulic Oil Filter ElementFilling the Fuel Tank Engine Air CleanerCleaning and/or Replacing Air Cleaner Element Engine Fuel SystemCharging the Battery Battery eLECTRIC Start ModelsBlade Inspection Blade ReplacementCutter Blades Jump StartingBody and deck TiresScag Approved Attachments and Accessories Illustrated Parts ListSection 36A Cutter Deck Description 48V & 52V Cutter Decks Cutter Deck w/Decals Cutter Deck Controls Deck Lift Weldment 48V Sheet Metal Components 462231 Steering Controls and Fuel Components 452055 Brake Weldment, LH Hydraulics and Engine Components Hydraulics and Engine Components Electrical System Instrument Panel w/Decal Switch, PTO 10 Amp 48798 Hydraulic Pump Assembly Housing Kit Heavy-Duty Commercial Replacement Decals and Information Plates SVR Electrical Schematic Limited Warranty Commercial Equipment