Scag Power Equipment STT61V-31EFI-SS manual Roll-Over Protection System

Page 10

R

Section 2

2.5 Roll-Over Protection System

WARNING

Reduce speed when turning, operating on slopes, slick or wet surfaces. Allow extra distance to stop.

Stay off of slopes too steep for safe operation. To check a slope, attempt to back up it (with the cutter deck down). If the machine can not back up the slope without the wheels slipping, do not operate the machine on this slope. Under no circumstances should the machine be operated on slopes greater than 15 degrees.

DO NOT mow near drop-offs, ditches or embankments. The machine could suddenly roll over if a wheel goes over the edge or if the edge caves in.

Operate the machine smoothly, no sudden turns, starts or stops on a slope.

NEVER tow on slopes. The weight of the towed equipment may cause loss of traction and loss of control.

DO NOT permit untrained personnel to operate the machine.

Be cautious when loading and unloading onto trailers or trucks.

Use only a full width ramp.

Ramp angle should be no more than 15 degrees.

Back up the ramp and drive down forward.

This mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Do not mow on wet grass. Wet grass reduces traction and steering control.

Any or all parts of the Roll-Over Protection System MUST NOT be removed. Failure to adhere to this guideline could result in injury or death.

FOLDABLE Roll-over protection system (if equipped)

WARNING

Keep the roll bar in the raised and locked position and the seat belt securely fastened during operation. Failure to do so could cause serious injury or loss of life.

Lower the roll bar only when absolutely necessary.

WARNING

There is no roll-over protection when the roll bar is in the down position.

Lower the roll bar only when absolutely necessary.

Raise the roll bar as soon as clearance permits.

DO NOT wear the seat belt when the roll bar is in the down position.

ALWAYS wear seat belt when roll bar is in the up position.

Operate the machine smoothly, no sudden turns, starts or stops.

Check the area carefully before mowing for proper overhead clearance (i.e. branches, doorways, etc.).

DO NOT contact any overhead object with the roll bar.

1.To lower the roll bar, loosen the tension knob on both the left hand and right hand bar. See Figure 2-1.

6

Image 10
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited Warranty Commercial Equipment Inside Back CoverDirection Reference General InformationIntroduction Servicing The Engine And Drive Train ComponentsSymbols Symbol DescriptionSignal Words Safety InformationBefore Operation Considerations Operation Considerations Section Roll-Over Protection System Foldable Roll-over protection system if equippedFoldable Roll-Over Protection System Maintenance Considerations & Storage Safety And Instructional Decals Install Belt COvER Before Operating MachineEngine SpecificationsPower Head ElectricalHydraulic System Weights And DimensionsCutter Deck ProductivityOperating Instructions Controls And Instrument IdentificationSafety Interlock System Dump Valve ControlGround Travel And Steering Initial Run-In ProceduresStarting The Engine Forward TravelEngaging The Deck Drive Cutter Blades Reverse TravelAfter Operation Hillside OperationParking The Mower Removing Clogged MaterialMoving Mower With Engine Stopped Adjusting Cutting HeightRecommendations For Mowing Adjusting The Steering Levers Adjusting The Height Adjust PedalTowing Optional Hitch Accessory Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Adjustments Parking Brake AdjustmentTravel Adjustments Neutral AdjustmentBelt Adjustment Throttle Control and Choke AdjustmentsTracking Adjustment Cutter Deck Level Cutter Deck AdjustmentsBelt Alignment Cutter Deck PitchCutter Deck Height Cutter Deck StopPosition Custom-Cut Baffle Adjustment Early Models Custom-Cut Baffle AdjustmentPosition Custom-Cut Baffle Adjustment Current Production Position Custom-Cut Baffle Adjustment Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine Oil Engine Fuel SystemCleaning and/or Replacing Air Cleaner Element Engine Air CleanerReplacing In-Line Fuel Filter Elements Charging the Battery BatteryJump Starting Cutter Blades Blade ReplacementDrive Belts Blade InspectionCutter Deck Gearbox Checking Lubricant LevelChanging Lubricant Cleaning the Radiator Debris ScreenCooling System Checking Coolant LevelBody, Deck, And Upholstery Checking The Fan Belt TensionIllustrated Parts List Scag Approved Attachments And Accessories61V Cutter Deck Description Cutter Deck Controls Cutter Deck Controls Suspension Seat Sheet Metal Components STT ROLL-OVER Protection System with Suspension Seat STT ROLL-OVER Protection System with Suspension Seat Deck Drive Components Belt Guard, Rear Hinge, Belt Guard 481309 Latch, Hood 482845 Engine & Attaching Parts 31HP-EFI Kohler Available through the individual engine manufacturer Brake and Steering Components Grip, Handle Bar Fuel and Hydraulic System Kohler 31EFI 24 403 BDP-16A Hydraulic Pump Assembly with Cooling FAN HG70924 Charge Pump Kit .19 STD. Splined HG51457 Electrical System 31HP-EFI Kohler Electrical System 31HP-EFI Kohler Heavy-Duty Commercial STT-EFI Decals Page2 Electrical Schematic Kohler 31HP EFI Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Precaución Precaución Para apropiada protección la lleve Siempre Corte DE Cuchillas Aire de filtro Del elemento del reemplazo y/o Limpieza .A Combustible de tanque del Llenado .A Precaución DEL Combustible DE Sistema Hidráulico Sistema Conexión de puntos de Lubricación 1.7 Figura Continuación Mantenimiento Personalizado corte de deflector del Ajuste 9-6 Figura Corte de plataforma la de Altura Corte de plataforma la de Inclinación Correa LA DE Alineación Neutral Ajuste Ajustes Inclinadas Crestas Corte de trayectoria laDe ancho del través Inclinado CorteLo a inclinadas Salientes Corte deTrayectoria la de ancho IrregularCortar sin césped CorteDe trayectorias entre De Franjas VetasDirección de palancas las de Ajuste Opcional Enganche de accesorio RemolqueCésped EL Corte DE Altura LA DE AjusteDetenido Motor EL CON Cortacésped DEL Desplazamiento Cortacéspedes DEL Estacionamiento Cuesta UNA EN OperaciónCorte DE Cuchillas Plataforma DE Transmisión LA DE Conexión Precaución reversa en DesplazamientoTerreno EL EN Desplazamiento DirecciónArranque DE Procedimientos Seguridad DE Bloqueo DE Sistema Plataforma de elevación de pie de PalancaOperación DE Instrucciones Identificación Instrumentos E ControlesScag parte de Número Sección Advertencia Almacenamiento Y Mantenimiento Seguridad de cinturón del Inspección 3-2 Figura Vuelco Contra Protección DE Sistema Operación DE Consideraciones Nota Seguridad DE Descripción Símbolo Símbolos General Información Continuación Contenido DE Tabla Contenido DE Tabla Advertencia Manual DEL Operador