Scag Power Equipment STT61V-25KBD manual Roll-over protection system

Page 10

R

Section 2

2.5 Roll-over protection system

WARNING

Keep the roll bar in the raised and locked position and the seat belt securely fastened during operation. Failure to do so could cause serious injury or loss of life.

This mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Do not mow on wet grass. Wet grass reduces traction and steering control.

Any or all parts of the Roll-Over Protection System MUST NOT be removed. Failure to adhere to this guideline could result in injury or death.

WARNING

There is no roll-over protection when the roll bar is in the down position.

Lower the roll bar only when absolutely necessary.

Raise the roll bar as soon as clearance permits.

DO NOT wear the seat belt when the roll bar is in the down position.

Lower the roll bar only when absolutely necessary.

1.To lower the roll bar, loosen the tension knob on both the left hand and right hand bar. See Figure 2-1.

2.Remove the hairpin cotter pins and remove the two

(2) lock pins. See Figure 2-2.

3.Lower the roll bar to the down position.

4.To raise the roll bar, lift the bar to the upright position.

5.Install the two (2) lock pins through the hole, secure with the two (2) hairpin cotter pins and tighten the tension knobs. See Figure 2-2. Remove the seat belt from the retainer brackets.

UPRIGHT AND

LOCKED POSITION

TENSION

KNOBS

Figure 2-1. Foldable Roll-Over Protection System

HAIR PIN

ALWAYS wear seat belt when roll bar is in the up position.

Operate the machine smoothly, no sudden turns, starts or stops.

LOCK PIN

TENSION KNOB

Check the area carefully before mowing for proper overhead clearance (i.e. branches, doorways, etc.).

DO NOT contact any overhead object with the roll bar.

Figure 2-2. ROPS Hinge

The potential exposure of the seat belt to severe environmental conditions make it crucial to inspect the seat belt system regularly.

6

Image 10
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator STT61V-28CAT-SSTable of Contents Adjustments Parking Brake Adjustment Travel Adjustments Direction Reference General InformationIntroduction Servicing The Engine and Drive TraiN ComponentsSymbols Symbol DescriptionSignal Words Safety InformationBefore Operation considerations Operation Considerations Section Roll-over protection system Foldable Roll-Over Protection SystemSeat Belt Inspection Maintenance Considerations & storage Using a spark arrestorSafety and Instructional Decals Diesel Fuel onlyEngine SpecificationsPower head ElectricalHydraulic System Weights and DimensionsCutter Deck SMT61VOperating Instructions Controls and Instrument IdentificationSafety Interlock System Dump Valve ControlGround Travel and Steering Starting the EngineForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelParking the Mower Rotating BladesHillside Operation After OperationMoving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Adjusting the Height Adjust Pedal Adjusting the Steering LeversTowing optional hitch accessory Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Cut, or Rough ContourScalping Blades Hitting Adjustments Parking Brake AdjustmentTravel Adjustments Neutral AdjustmentBelt Adjustment Throttle Control and Choke AdjustmentsTracking Adjustment Cutter Deck Level Cutter Deck AdjustmentsBelt Alignment Cutter Deck PitchCutter Deck Height Cutter Deck StopCustom-Cut Baffle Adjustment Custom-Cut Baffle AdjustmentElectric clutch adjustment Clutch Air Gap AdjustmentMaintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine Oil Engine Fuel SystemCleaning and/or Replacing Air Cleaner Element BatteryEngine Air Cleaner Replacing In-Line Fuel Filter ElementsBlade Inspection Charging the BatteryCutter Blades Jump StartingTires Blade ReplacementBlade Sharpening Checking Lubricant Level Cutter Deck GearboxCooling System Changing LubricantBODY, DECK, and Upholstery Cleaning the Radiator Debris ScreenChecking The Fan Belt Tension Illustrated Parts List Scag Approved Attachments and AccessoriesIllustrated Parts List Section 61V & 72V Cutter Deck Description Cutter Deck Controls 481764 Link, Deck Lift Sheet Metal Components Sheet Metal Components Section STT ROLL-OVER Protection System with Suspension Seat 9292 Deck Drive Components Deck Drive Components Engine & Attaching Parts CAT Diesel Available through the individual engine manufacturer Radiator & Attaching Parts CAT Diesel Radiator & Attaching Parts CAT Diesel Engine & Attaching Parts Kubota Diesel 424633 Latch, Hood Brake and Steering Components Brake and Steering Components Fuel and Hydraulic System CAT Diesel Fuel and Hydraulic System CAT Diesel Fuel and Hydraulic System Kubota Diesel Hose Assy, 1/2 ID Tank to Filter Base Section BDP-16A Hydraulic Pump Assembly with Cooling Fan Hex Screw, Flanged Head M10 x 1.50-65mm Electrical System CAT Diesel Electrical System CAT Diesel Electrical System Kubota Diesel 483643 Cover, Sealed Single 483641 Replacement Decals and Information Plates Manufactured Under ONE or MoreSttkbd Decals Page2 Electrical Schematic CAT Diesel COMElectrical Schematic Kubota Diesel Glow Plug POS NEG Volt Meter PTO Switch Module RelayLimited Warranty Commercial Equipment