Scag Power Equipment STT61V-25KBD BODY, DECK, and Upholstery, Cleaning the Radiator Debris Screen

Page 43

Section 7

R

Fill to Bottom of

Filler Neck

030467-13

Figure 7-9. Coolant Level in Radiator

3.Replace the radiator cap. Push down on the cap and turn clockwise until it stops.

- NOTE -

The cooling system should be flushed and the coolant replaced every 500 hours of operation or annually. See your Scag dealer for proper coolant replacement.

B. Cleaning the Radiator Debris Screen

After each day of operation, remove and clean the radiator debris screen.

caution

To avoid personal injury, always wear safety glasses when using compressed air.

1.Release latches and pull the debris screen up to remove.

2.Clean the debris screen with compressed air or a water hose.

- NOTE -

Check the radiator for excessive debris and clean with compressed air. Never spray a hot engine with water, use only compressed air to remove debris.

3. Re-install the debris screen to the radiator.

C. Checking The Fan Belt Tension

Periodically check the fan belt tension. The belt should deflect 1/2" with 10 pounds of pressure. See your Scag dealer if the belt is in need of adjustment or replacement.

7.13 BODY, DECK, AND UPHOLSTERY

caution

Do not wash any portion of the equipment while it is hot. Do not wash the engine; use compressed air.

1.After each use, wash the mower and cutter deck. Use cold water and automotive cleaners. Do not use pressure cleaners.

2.Do not spray electrical components.

3.Use a mild soap solution or a vinyl/rubber cleaner to clean the seat.

4.Repair damaged metal surfaces using Scag touch- up paint available from your authorized Scag dealer. Wax the mower for maximum paint protection.

39

Image 43
Contents OPERATOR’S Manual STT61V-28CAT-SS Remember Your Mower is only AS Safe AS the OperatorTable of Contents Adjustments Parking Brake Adjustment Travel Adjustments Servicing The Engine and Drive TraiN Components General InformationIntroduction Direction ReferenceSymbol Description SymbolsSignal Words Safety InformationBefore Operation considerations Operation Considerations Section Foldable Roll-Over Protection System Roll-over protection systemSeat Belt Inspection Using a spark arrestor Maintenance Considerations & storageDiesel Fuel only Safety and Instructional DecalsElectrical SpecificationsPower head EngineSMT61V Weights and DimensionsCutter Deck Hydraulic SystemControls and Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemGround Travel and Steering Starting the EngineForward Travel Reverse Travel Engaging the Deck Drive Cutter BladesAfter Operation Rotating BladesHillside Operation Parking the MowerMoving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Adjusting the Steering Levers Adjusting the Height Adjust PedalTowing optional hitch accessory Condition Cause Cure Troubleshooting Cutting ConditionsCut, or Rough Contour Troubleshooting Cutting Conditions ContdScalping Blades Hitting Parking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsBelt Adjustment Throttle Control and Choke AdjustmentsTracking Adjustment Cutter Deck Pitch Cutter Deck AdjustmentsBelt Alignment Cutter Deck LevelCutter Deck Stop Cutter Deck HeightCustom-Cut Baffle Adjustment Custom-Cut Baffle AdjustmentClutch Air Gap Adjustment Electric clutch adjustmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OilReplacing In-Line Fuel Filter Elements BatteryEngine Air Cleaner Cleaning and/or Replacing Air Cleaner ElementJump Starting Charging the BatteryCutter Blades Blade InspectionTires Blade ReplacementBlade Sharpening Changing Lubricant Cutter Deck GearboxCooling System Checking Lubricant LevelBODY, DECK, and Upholstery Cleaning the Radiator Debris ScreenChecking The Fan Belt Tension Scag Approved Attachments and Accessories Illustrated Parts ListIllustrated Parts List Section 61V & 72V Cutter Deck Description Cutter Deck Controls 481764 Link, Deck Lift Sheet Metal Components Sheet Metal Components Section STT ROLL-OVER Protection System with Suspension Seat 9292 Deck Drive Components Deck Drive Components Engine & Attaching Parts CAT Diesel Available through the individual engine manufacturer Radiator & Attaching Parts CAT Diesel Radiator & Attaching Parts CAT Diesel Engine & Attaching Parts Kubota Diesel 424633 Latch, Hood Brake and Steering Components Brake and Steering Components Fuel and Hydraulic System CAT Diesel Fuel and Hydraulic System CAT Diesel Fuel and Hydraulic System Kubota Diesel Hose Assy, 1/2 ID Tank to Filter Base Section BDP-16A Hydraulic Pump Assembly with Cooling Fan Hex Screw, Flanged Head M10 x 1.50-65mm Electrical System CAT Diesel Electrical System CAT Diesel Electrical System Kubota Diesel 483643 Cover, Sealed Single 483641 Manufactured Under ONE or More Replacement Decals and Information PlatesSttkbd Decals Page2 COM Electrical Schematic CAT DieselGlow Plug POS NEG Volt Meter PTO Switch Module Relay Electrical Schematic Kubota DieselLimited Warranty Commercial Equipment