RedMax LRTZ2401-CA manual Operation, OP1 OP2 OP3 OP4 Starting Engine

Page 28

English

8. Operation

OP1

OP2	(1)

(2)

(3)

OP3

(5)

(6)

(4)

(7)

OP4

■STARTING ENGINE

WARNING

The cutting head will start rotating upon the engine starts.

1.Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine.

2.Push the primer pump several times until overflown fuel flows out in the clear tube. (OP1)

3.Move the choke lever to the closed position. (OP2)

4.Set the ignition switch to the “Start” position. While pulling the throttle lever, push the throttle set button, and release the throttle, then the throttle lever is in to the “Start position”. (OP3)

5.While holding the unit firmly, pull out the starter rope quickly until engine fires. (OP4)

(1) choke lever	(2) close
(3) open	(4) ignition switch
(5) start	(6) stop

(7) Throttle set button

IMPORTANT

•Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures.

6.Move the choke lever downward to open the choke. And restart engine. (OP2)

7.Allow the engine to warm up for several minutes before starting operation.

NOTE

1.When restarting the engine immediately after stopping it, leave the choke open.

2.Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it.

28

Image 28

Contents LRTZ2401-CA Information Informationinformación Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Specifications Parts locationFiche technique Emplacement des pieces Situación de las piezasEspecificaciohes Symbols on the machine PositionEmplacement PosiciónWorking Condition For safe operationWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoLA Machine Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineDemarrage DU Moteur Utilisation DE LA MachineArranque DEL Motor USO DEL ProductoMaintenance If Someone ComesSI QUELQU’UN S’APPROCHE SI Alguien SE Aproxima EntretienTout est en ordre de marche MantenimientoRefill after cooling the engine Handling FuelTransportation Manipulation DU Carburant Manipulación DEL CombustibleLlenar una vez que el motor se haya enfriado TransportSet up SE1 SE2 Installing HandleAttaching the Trimming Mechanism SE2 Balance UnitAssemblage Montaje Mise EN Place DE LA PoigneeInstalación DEL Mango Equilibrage DE LA MachineFuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda OP1 OP2 OP3 OP4 Starting Engine OperationCutting head will start rotating upon the engine starts Fonctionnement Uso Palanca del estrangulador 2 cerrarAdjusting Throttle Cable Adjusting Idling Speed OP6OP5 OP6 Stopping Engine OP3Reglage Câble D’ACCÉLÉRATEUR Ajuste Cable DEL AceleradorReglage DU Ralenti OP6 Ajuste DE LA Velocidad DE Marcha EN Vacío OP6OP7 Adjusting the Angle of the Cutting Blades OP7 Clamp bolt Trimming mechanism Tighten LoosenRéglage DE Langle DES Lames Tranchantes OP7 Boulon de serrage Mécanisme de coupe Serrer DesserrerAjuste DEL Ángulo DE LAS Cuchillas DE CORTE. OP7 Perno de sujeción Mecanismo de poda Ajustar AflojarMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoMA1 Blades MA1Quick TIP MA2Entretien Mantenimiento Replacement Plug is a NGK CMR7H MA3 MA4 MA5AIR Filter Fuel FilterFiltre a AIR Filtro DE AireFiltre a Carburant Filtro DE Combustible Bougie D’ALLUMAGE BujíaMuffler MA6 Spark ArresterSpark arrester Intake AIR Cooling VentPARE-ETINCELLES Ouïe DU Refroidissement PAR AIRParachispas Toma DE Aire DE RefrigeraciónProcedures to be Performed After Every 100 Hours of USE StorageDisposal MA7 MA8Procedure a Effectuer Toutes LES 100 Heures D’UTILISATION Rangement AlmacenamientoMise au rebut Eliminación Procedimientos a Realizar Cada 100 Horas DE USO12. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes LRTZ2401 LRTZ2401-CA NotaParts list Cutting Unit LRTZ2401/LRTZ2401-CA S/N Z000001 and up Engine Unit LRTZ2401/LRTZ2401-CA S/N 60100101 and up Qty Key# Part Number Description Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control LRTZ2401Mesures DE Lutte Contre LES Emissions Control DE Emisiones