Poulan SM30SB Removing Trimmer ATTACH- Ment or Other Optional Attachments, Operating Position

Page 12

WARNING: Always stop unit and dis- connect spark plug before removing or instal- ling attachments.

REMOVING TRIMMER ATTACH- MENT (OR OTHER OPTIONAL ATTACHMENTS)

CAUTION: When removing or installing at- tachments, place the unit on a flat surface for stability.

1.Loosen the coupler by turning the knob counterclockwise.

Coupler

AttachmentLOOSEN

Locking/Release

Button in Primary Hole

OPERATING INSTRUCTIONS

It is recommended that the engine not be operated for longer than 1 minute at full throttle.

OPERATING POSITION

Knob

TIGHTEN

2. Press and hold the locking/release button.

Locking/Release

Button

ALWAYS WEAR:

Hearing protection

Long pants

Eye protection

Attachment

Coupler

Upper Shaft

3.While securely holding the engine and upper shaft, pull the attachment straight out of the coupler.

INSTALLING OPTIONAL ATTACH- MENTS

1.Remove the shaft cap from the attach- ment (if present).

2.Position locking/release button of attach- ment into guide recess of coupler.

3.Push the attachment into the coupler until the locking/release button snaps into the primary hole.

4.Before using the unit, tighten the knob se- curely by turning clockwise.

Coupler Primary Hole

Guide Recess

Locking/

Upper Release Attachment

Shaft Button

WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before op- erating the unit. All attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual. Using the wrong hole could lead to seri- ous injury or damage to the unit.

Heavy shoes

Cut only from your left to your right.

WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

When operating unit, stand as shown and check for the following:

SWear eye protection and heavy clothing. S Hold trigger handle with your right hand and

assit handle with left hand. S Keep unit below waist level.

S Cut only from your left to your right to ensure debris is thrown away from you. Without bending over, keep line near and parallel to the ground and not crowded into material being cut.

Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool. Always release the throttle trigger and allow the en- gine to return to idle speed when not cutting.

To stop engine:

S Release the throttle trigger.

S Move the ON/STOP switch to the STOP position.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Manual de Instrucciones Manuel d’Instructions Table of Contents Identification of Safety SymbolsIdentification of Safety Symbols Safety Rules Operator SafetyOptional Attachments Unit / Maintenance Safety Fuel SafetyLine Trimmer Safety Additional Safety RulesEdger Safety BLOWER/VACUUM SafetyBrushcutter Safety HandlebarCultivator Safety Hedge Trimmer SafetyPole Pruner Safety Cut from your right to your leftSnow Thrower Safety High speed causing injuryKnow how to stop quickly AnotherAssembly Installing Trimmer ATTACH- MentAttaching the Shield Operation HOW to Stop Your Unit HOW to Start Your UnitStarting a Cold Engine Starting a Warm EngineInstalling Optional ATTACH- Ments Removing Trimmer ATTACH- Ment or Other Optional AttachmentsOperating Position Remove the shaft cap from the attach- ment if presentGood clean job Cutting MethodsTip of the line Does the cutting Work areaMaintenance Service and Adjustments Carburetor Idle Speed AdjustmentReplacing the Line Replacing the Cutting HeadSeasonal Storage Fuel SystemEngine OtherTroubleshooting Table Cause Remedy Limited Warranty Statesville RoadCanada, contact Ligations The U.S. EnvironmentalIntermediate 125 hours Extended 300 hours

115225426, 966479401, SM30SB specifications

The Poulan SM30SB is a notable addition to the range of outdoor power equipment, specifically designed for lawn care enthusiasts and professionals seeking a reliable and efficient solution for maintaining their gardens and lawns. This robust machine is equipped with several cutting-edge features and technologies that enhance its performance and usability, making it a preferred choice for many.

One of the standout features of the Poulan SM30SB is its powerful engine. The model is typically powered by a 30cc two-stroke engine that delivers impressive torque and performance, allowing users to tackle a wide variety of lawn tasks. This high-performance engine ensures that users can efficiently manage different types of vegetation, from delicate weeds to tougher shrubs.

The design of the SM30SB emphasizes user comfort and control. It is equipped with an ergonomic handle that is adjustable to accommodate different users, providing a comfortable grip during operation. This design reduces fatigue during extended use, which can be particularly beneficial for those large mowing jobs. Additionally, the lightweight structure of the unit allows for easy maneuverability, enabling users to navigate around obstacles with ease.

Another key characteristic of the Poulan SM30SB is its advanced cutting technology. The model features a dual-line bump feed cutting head, which allows for quick and easy line replacement and ensures a clean and precise cut every time. This system increases efficiency, enabling the user to complete tasks more swiftly without sacrificing quality.

The SM30SB also incorporates fuel-efficient technologies that minimize fuel consumption while maximizing output. This not only has a positive environmental impact but also means users spend less on fuel while achieving outstanding results. Its easy-start feature eliminates the hassle of struggling with ignition, allowing users to get started on their tasks without delays.

Maintenance is often a concern for outdoor equipment, and the design of the Poulan SM30SB addresses this with its easy-access air filter and spark plug. Regular maintenance can be performed quickly, ensuring that the equipment remains in top condition and ready for use whenever needed.

In conclusion, the Poulan SM30SB, model numbers 115225426 and 966479401, is a versatile and efficient tool that combines power with user-friendly features. With its robust engine, ergonomic design, advanced cutting technology, and environmental considerations, it stands out as an excellent choice for anyone looking to maintain their outdoor space effectively.
Top Page Image Contents