Poulan SM30SB, 966479401 Service and Adjustments, Replacing the Line, Replacing the Cutting Head

Page 15

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

For unit to operate properly, the cutting line should be replaced when line becomes worn to less than 3 inches in length from the edge of the line exit tunnels on each side of the cutting head.

1.Remove and discard worn line before installing new line.

2.Use only 0.115 inch (3 mm) diameter Poulan PRO brand cut length line.

3.Insert one end of the line through the positioning tunnel.

4.Continue to feed line through tunnel until line is centered (leaving equal amounts on each side). See illustration below.

Positioning tunnel

5.Insert ends of line one at a time through the line exit tunnels.

6.Pull the line and make sure the line is ex- tended fully through the tunnels.

Line exit

Line exit

tunnel

tunnel

7.Correctly installed line will be the same length on both ends.

REPLACING THE CUTTING HEAD

1.Align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup.

2.Insert a small screwdriver into aligned holes. This will keep the shaft from turning while removing and installing trimmer head.

Screwdriver

3.While holding the screwdriver in position, remove trimmer head by turning clock- wise (looking from bottom of unit).

4.Thread replacement trimmer head onto the shaft by turning counterclockwise. Tighten until secure.

5.Remove the screwdriver.

CARBURETOR IDLE SPEED

ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head, blade or any optional attachment will be spinning during most of this procedure. Wear your protective equipment and observe all safe- ty precautions. After making adjustments, the trimmer head, blade or any optional attachment must not move/spin at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is released.

S The trimmer head, blade or optional attachment moves/spins at idle.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

To adjust idle speed:

Allow engine to idle. Adjust speed until engine runs without trimmer head, blade or optional attachment moving or spinning (idle too fast) or stalling (idle speed too slow).

STurn idle speed screw clockwise to increase

engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed if trimmer head, blade or optional attachment moves or spins at idle.

WARNING: Recheck the idle speed after each adjustment. The trimmer head, blade or optional attachment must not move or spin at idle speed to avoid serious injury to the operator or others.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Table of ContentsIdentification of Safety Symbols Safety Rules Operator SafetyOptional Attachments Additional Safety Rules Unit / Maintenance SafetyFuel Safety Line Trimmer SafetyHandlebar Edger SafetyBLOWER/VACUUM Safety Brushcutter SafetyCut from your right to your left Cultivator SafetyHedge Trimmer Safety Pole Pruner SafetyAnother Snow Thrower SafetyHigh speed causing injury Know how to stop quicklyAssembly Installing Trimmer ATTACH- MentAttaching the Shield Operation Starting a Warm Engine HOW to Stop Your UnitHOW to Start Your Unit Starting a Cold EngineRemove the shaft cap from the attach- ment if present Installing Optional ATTACH- MentsRemoving Trimmer ATTACH- Ment or Other Optional Attachments Operating PositionDoes the cutting Work area Good clean jobCutting Methods Tip of the lineMaintenance Replacing the Cutting Head Service and AdjustmentsCarburetor Idle Speed Adjustment Replacing the LineOther Seasonal StorageFuel System EngineTroubleshooting Table Cause Remedy Ligations The U.S. Environmental Limited WarrantyStatesville Road Canada, contactIntermediate 125 hours Extended 300 hours

115225426, 966479401, SM30SB specifications

The Poulan SM30SB is a notable addition to the range of outdoor power equipment, specifically designed for lawn care enthusiasts and professionals seeking a reliable and efficient solution for maintaining their gardens and lawns. This robust machine is equipped with several cutting-edge features and technologies that enhance its performance and usability, making it a preferred choice for many.

One of the standout features of the Poulan SM30SB is its powerful engine. The model is typically powered by a 30cc two-stroke engine that delivers impressive torque and performance, allowing users to tackle a wide variety of lawn tasks. This high-performance engine ensures that users can efficiently manage different types of vegetation, from delicate weeds to tougher shrubs.

The design of the SM30SB emphasizes user comfort and control. It is equipped with an ergonomic handle that is adjustable to accommodate different users, providing a comfortable grip during operation. This design reduces fatigue during extended use, which can be particularly beneficial for those large mowing jobs. Additionally, the lightweight structure of the unit allows for easy maneuverability, enabling users to navigate around obstacles with ease.

Another key characteristic of the Poulan SM30SB is its advanced cutting technology. The model features a dual-line bump feed cutting head, which allows for quick and easy line replacement and ensures a clean and precise cut every time. This system increases efficiency, enabling the user to complete tasks more swiftly without sacrificing quality.

The SM30SB also incorporates fuel-efficient technologies that minimize fuel consumption while maximizing output. This not only has a positive environmental impact but also means users spend less on fuel while achieving outstanding results. Its easy-start feature eliminates the hassle of struggling with ignition, allowing users to get started on their tasks without delays.

Maintenance is often a concern for outdoor equipment, and the design of the Poulan SM30SB addresses this with its easy-access air filter and spark plug. Regular maintenance can be performed quickly, ensuring that the equipment remains in top condition and ready for use whenever needed.

In conclusion, the Poulan SM30SB, model numbers 115225426 and 966479401, is a versatile and efficient tool that combines power with user-friendly features. With its robust engine, ergonomic design, advanced cutting technology, and environmental considerations, it stands out as an excellent choice for anyone looking to maintain their outdoor space effectively.
Top Page Image Contents