Lexicon DC-2 owner manual Installation, Remote Control

Page 12

DC-2 Digital Controller

Installation

 

 

 

 

The Remote Control

1 ON, FP and OSD

ON turns the DC-2 on and selects the input last used with main and Zone 2 volume levels set to the levels cho- sen in the OUTPUT LEVELS menu.

FP (ON) turns on the front panel display backlight and the Lexicon logo.

OSD (ON) activates the DC-2 on-screen display.

2 OFF, FP and OSD

OFF puts the unit into standby and mutes all of the outputs.

OSD (OFF) turns off the on- screen display.

FP (OFF) turns off the front panel display backlight and the Lexicon logo.

3 SELECT, ▲,▼ and DONE Allow access to and adjust- ment of all displayed menu items. ▲ and ▼ step a dis- play cursor through listed menu items. SELECT dis- plays submenus, or chooses a menu item for adjustment. The ▲ and ▼ buttons alter the settings of selected pa- rameters. DONE saves the current changes and exits the menu.

4 Shift

2

OFF

 

ON

1

 

FP

FP

OSD

 

 

OSD

 

 

3

Shift

 

Record

 

4

DONE

SELECT

 

5

 

 

 

6

 

 

Zone 2

 

 

 

 

 

 

F

Light

V

 

7

 

O

8

X

 

 

L

 

 

 

 

Mute

9

 

VCR DVD VDisc TV

10

AUX CD Tuner Tape

Digital Controller

EFFECTS11

2 CH

Party

TV M

Music

 

 

8 VOL ▲ and ▼

These controls display, then adjust the current master vol- ume level. The activated dis- plays (FP or OSD) will show the volume level and a visual guage.

When Mute is engaged, these controls display, then adjust the volume from the mute level. When full mute is en- gaged (⇑Mute), these con- trols increase or decrease the selected volume level with- out disengaging full mute.

9 Mute

Engages Mute and reduces the volume by the amount selected in the OUTPUT LEV- ELS menu. The red Mute LED on the front panel will light and the activated displays (FP or OSD) will show MUTE ON. Pressing again restores the volume to its pre-Mute level, turns off the front panel Mute LED, and displays MUTE OFF on the active displays.

10 Input Selection

Individual buttons select from 8 inputs and activate a corre- sponding green LED on the front panel. Depending on the Setup configuration, selection may also load a new effect.

When pushed in conjunction with other remote buttons, activates a set of less-used, but convenient, functions.

5 Record/Zone 2

When pushed in conjunction with other remote buttons, activates a set of Record/ Zone 2 control functions.

6 Light

Toggles the remote control backlight on and off. (Note: after seven seconds, the backlight is automatically turned off.)

7 FX ▲ and ▼

These controls display, then change the current effect. The activated displays (FP or OSD) will show the effect name.

11 EFFECTS

These controls select Dolby, THX, Logic 7, dts, 2-Chan- nel, Party, TV Matrix or Music playback. The actual effect is determined by the format of the input signal.

Note: When 2-Channel is engaged, pressing the but- ton again will turn it off.

3

Page 11 Page 13
Image 12
Page 11 Page 13
Contents DC-2 Important Safety Instructions Communications NoticeAcknowledgements Vigtig information om sikkerhed Wichtige Sicherheitsanweisungen Contents Troubleshooting Specifications Installation WorksheetPCM Effects and Parameters AC-3 Effects and ParametersIntroduction Using the Documentation Glossary of TermsPage Controls Indicators Front PanelInstallation Rear PanelInstallation Remote ControlAlternate Remote Control Functions Using the ShiftPress and hold with buttons shown to access these remote Record/Zone 2 buttonsPress and hold with Connection Location Considerations AC ConnectionsWiring Considerations Wire Lengths AWG SizeAudio/Video Connections Audio/Video CablesVideo Disc Player AC-3 RF Video Connections Digital Audio ConnectionsAC-3 Ready Laser Disc LD/DVD PlayersRestore Factory Defaults Adjust with orEqualization +0.0dBTilt LoudnessDisplay Adjustment Video On-Screen DisplayDisplay Adjust Menu ON-SCREEN Display Input Configuration Input GainAnalog Inputs Only Restore Input Name Input Level MetersInput Name Input Effect FX AssignmentAutomatic AC-3 FXSystem Configuration PCM Only AC-3 Only DTS OnlyVideo Coax 1-5Digital Audio Inputs Record/Zone Record/Zone 2 ControlsOFF Speaker Configuration Custom ConfigurationPGM Trigger Assignment Front L/RCenter Sides RearsSetting Output Levels THX ConfigurationConfiguration Subwoofer OutputOutput Levels Menu Subwoofer Peak Limiter LimiterMute Level Power On Volume Zone 2 Power On Volume Speaker DistanceSync Delay Calibrate Panorama OFF Sync DLY Balance Zone 2 Balance Locking Settings Assign Custom NameUsing DC-2 Effects Comparing a modified Effect to the factory preset versionCustomizing Effects Restoring the original parameter values of an Effect Listening to only the DC-2 Effect Front/Back FaderPanorama NightclubPCM Effects and Parameters Party ChannelMusic Surround Music Logic LogicTV Matrix Pro LogicMono Logic Dialog in the centerPCM Effects and Parameters PCM Effects and Parameters PCM Effects and Parameters PCM Effects and Parameters AC-3 Status Display Data Rate 384 kb/sec4dB AC-3 Effects and Parameters MusicDolby Digital THX Including Surround EXAC-3 Effects and Parameters AC-3 Effects and Parameters DTS 2-Channel DTS MusicDTS Logic DTS FilmDTS THX DTS Effect ParametersDTS Effects and Parameters Troubleshooting Problem Possible Cause and SolutionTroubleshooting Routine Maintenance Restoring Defaults ExitSpecifications Speaker Configuration circle selection Inputs

DC-2 specifications

The Lexicon DC-2 is a renowned digital surround sound processor that has garnered appreciation for its advanced technology and superior audio performance. Designed specifically for home theater systems and high-end audio setups, the DC-2 is a versatile unit that can provide high-quality sound reproduction in a variety of environments.

One of the standout features of the Lexicon DC-2 is its dual DSP architecture. This advanced processing technology enables the processor to handle complex audio formats with ease, delivering immersive soundscapes for both music and movies. The DC-2 supports formats such as Dolby Digital, DTS, and other surround sound technologies, ensuring compatibility with a wide range of media sources.

Another key characteristic of the DC-2 is its extensive connectivity options. It is equipped with multiple inputs and outputs, including analog and digital connections, which allow for seamless integration with various audio and video components. This flexibility makes it an ideal choice for those seeking to create a custom audio setup tailored to their specific needs.

The Lexicon DC-2 also features sophisticated room correction capabilities. Using the proprietary Lexicon Room Correction (LRC) technology, it analyzes the acoustic characteristics of your listening space and adjusts the audio output accordingly. This ensures optimal sound quality regardless of the room's shape or size, enhancing the overall listening experience.

Moreover, its user-friendly interface and remote control functionality offer intuitive operation, making it easy for users to navigate through different settings and modes. The LCD screen displays vital information, allowing for quick adjustments on the fly.

In terms of audio quality, the DC-2 is known for its pristine sound clarity and dynamic range. With a robust signal-to-noise ratio, it minimizes distortion and delivers a clean, accurate audio signal. Audiophiles appreciate the fidelity with which it reproduces music, bringing studio-quality sound to the home environment.

In summary, the Lexicon DC-2 is a powerful digital surround sound processor that combines advanced technologies and innovative features to provide a premier audio experience. Suitable for both casual listeners and serious audiophiles, it stands as a testament to Lexicon’s dedication to audio excellence. Its versatility, connectivity, room correction, and exceptional sound quality make the DC-2 an outstanding choice for any modern home theater system.
Top Page Image Contents