Lexicon DC-2 owner manual Installation, Rear Panel

Installation

Lexicon

The Rear Panel

CAUTION: Never make or break any connections to the DC-2 with the rear-panel power ON. Make sure any associated amplifiers are turned off before turning this master power switch on or off.

	4
TRIGGERS	TRIGGERS
	IR IN
PGM GND PWR	GND
	PWR PGM

5	6	7	9
		8

DC-2

LEXICON, INC. ASSEMBLED IN U.S.A. 100-240V 50-60 Hz

SERIAL NO.

TAPE TUNER CD

L

AUDIO

R

S-VIDEO VIDEO

AUX	TV	V-DISC	DVD	VCR
	L			L
	R			R
	INPUT

MONITOR

ZONE 2 RECORD

L

R

OUTPUT

CAUTION	S/PDIF INTPUTS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR	MAIN OUTPUTS

		S/PDIF OUT
1	2	A	B	C
		EXPANSION PORTS		RS 232

3	4	5
		1	2	3

					LISTED AUDIO
REAR	SIDE	CENTER	FRONT	C	EQUIPMENT
					7D77
					E172268
	L		TRIGGERS	TRIGGERS
				IR IN
	R
		SUBWOOFER	PGM GND PWR	PWR PGM	GND

POWER

1

1 AUDIO INPUTS

Eight stereo analog audio in- puts are switched with corre- sponding video inputs and fed to the Monitor outputs. Inputs are nominally labeled as origi- nating from an audio tape player, tuner, CD player, an unspecified auxiliary source, a TV tuner, a Laser or Video Disc player, a DVD player, and a VCR.

2 ZONE2 and RECORD Each pair of stereo audio outputs supplies the same signal according to the Record/Zone 2 input selec- tion. Zone 2 output levels can be controlled independently for use with amplifiers and speakers in another room. Record can be expanded to two outputs using standard Y-connectors. Both outputs are muted in Standby.

2

3 MAIN OUTPUTS

Three stereo amplifier out- puts are provided for front, side and rear speakers. Single monaural outputs are provided for the center speaker and the subwoofer. The audio outputs are muted in Standby.

4 IR Input, PWR and

PGM TRIGGERS

The IR input is an 1/8" mono phone jack connector for in- put of IR data from any indus- try-standard IR source. Data is retransmitted by an IR LED mounted near the front panel IR receiver.

Two trigger outputs are pro- vided on 4-pin removable screw terminals, and a 5-pin DIN connector, as shown in the expanded illustration above. The PWR trigger is high when the DC-2 is on, low in standby or when the unit is off. The PGM trigger can be enabled (high) or disabled (low) for specific input selec- tions in the Input Configura- tion menu. High is indicated by either +12VDC or +5VDC, selectable via an internal jumper. (Factory configura- tion is +12V.)

3

5 VIDEO INPUTS and

OUTPUTS

Five video input sources are provided. Video inputs are selected based on selections made in the INPUT CONFIG menu and fed to the selected monitor output jack. Record output jacks can be selected independently.

RCA (composite) and S- video connectors are pro- vided for monitor and record. If an S-video input is used, both S-video and composite are available at each output. If the video input is compos- ite, only composite is avail- able at each output. The monitor output incorporates the on-screen video overlay. Unless RECORD is enabled, the record output follows the monitor output selection with- out the on-screen display fea- ture. Both outputs are off in Standby.

10

4

6 S/PDIF INPUTS

Five coaxial RCA connectors and three optical connectors are provided for digital audio inputs.

7 EXPANSION PORTS

Reserved for future upgrades.

8 RS 232

Serial port connector for au- tomation and control systems.

9 Power On/Off

Master power switch discon- nects the AC Mains. This switch is intended to be left On during regular use. When- ever cables are connected or disconnected, or when the unit is not going to be used for an extended period of time, this switch should be set to Off.

10 POWER

AC power connector: 3-wire, 10 Amp, IEC 320.

2