Lexicon DC-2 owner manual Restore Factory Defaults, Equalization, Adjust with or, +0.0dB

Page 19

DC-2 Digital Controller

System 2

Configuration System

Configuration

Restore

Factory Defaults

Although the DC-2 memory is cleared before it leaves the factory, it is good practice to restore the factory defaults with the following procedure before system configuration.

Turn the DC-2 OFF with the remote control. Turn the unit back ON and immediately press and hold the MUTE button on the remote. (Make sure you do not block the infrared receiver on the DC-2 front panel.) The display will read:

FACTORY PRESETS MENU

EXIT

RESTORE DEFAULTS

Press ▼ to highlight RESTORE DEFAULTS, then press SELECT. This will clear and reload all preset effects and all factory settings of Volume, Balance, Contrast, Configuration, etc. When the message FACTORY DE- FAULTS RESTORED is displayed, press DONE to return to normal opera- tion.

In the main menu, press SELECT to open the Equalization menu which contains Bass, Treble and Tilt controls, and a Loudness parameter.

 

EQUALIZATION MENU

Adjust with ▲or ▼

 

BASS LEVEL

+0.0dB

 

 

 

-6.0 to +6.0dB

 

TREBLE LEVEL +0.0dB

-6.0 to +6.0dB

 

TILT

+0.0dB

-3.0dB to +3.0dB

 

LOUDNESS

ON

 

 

ON, OFF

Bass and Treble level controls are provided to compensate for inconsisten- cies in source material, rather than variations in room conditions. The BASS LEVEL control allows a boost or cut of as much as 6dB below 250Hz. The TREBLE LEVEL control allows a boost or cut of 6dB above 1.5kHz. To select either control for adjustment, use▲or ▼to select the control, press SELECT, and use ▲ or ▼ to adjust the setting.

These controls do not affect the sound of rear or side speakers.

Equalization

MAIN MENU

EFFECT ADJUST

EQUALIZATION

DISPLAY ADJUST

SETUP

Bass and Treble Level

11

Page 18 Page 20
Image 19
Page 18 Page 20
Contents DC-2 Communications Notice Important Safety InstructionsAcknowledgements Vigtig information om sikkerhed Wichtige Sicherheitsanweisungen Contents AC-3 Effects and Parameters TroubleshootingSpecifications Installation Worksheet PCM Effects and ParametersIntroduction Glossary of Terms Using the DocumentationPage Front Panel Controls IndicatorsRear Panel InstallationRemote Control InstallationRecord/Zone 2 buttons Alternate Remote ControlFunctions Using the Shift Press and hold with buttons shown to access these remotePress and hold with Location Considerations AC Connections ConnectionAudio/Video Cables Wiring ConsiderationsWire Lengths AWG Size Audio/Video ConnectionsVideo Disc Player AC-3 RF LD/DVD Players Video ConnectionsDigital Audio Connections AC-3 Ready Laser Disc+0.0dB Restore Factory DefaultsAdjust with or EqualizationLoudness TiltVideo On-Screen Display Display AdjustmentDisplay Adjust Menu ON-SCREEN Display Input Gain Input ConfigurationAnalog Inputs Only Input Effect FX Assignment Restore Input NameInput Level Meters Input NameAC-3 FX AutomaticSystem Configuration DTS Only PCM Only AC-3 OnlyCoax 1-5 VideoDigital Audio Inputs Record/Zone 2 Controls Record/ZoneOFF Front L/R Speaker ConfigurationCustom Configuration PGM Trigger AssignmentSides Rears CenterSubwoofer Output Setting Output LevelsTHX Configuration ConfigurationOutput Levels Menu Limiter Subwoofer Peak LimiterSpeaker Distance Mute Level Power On Volume Zone 2 Power On VolumeSync Delay Calibrate Panorama OFF Sync DLY Balance Zone 2 Balance Assign Custom Name Locking SettingsComparing a modified Effect to the factory preset version Using DC-2 EffectsCustomizing Effects Listening to only the DC-2 Effect Front/Back Fader Restoring the original parameter values of an EffectNightclub PanoramaPCM Effects and Parameters Channel PartyMusic Surround Logic Music LogicPro Logic TV MatrixDialog in the center Mono LogicPCM Effects and Parameters PCM Effects and Parameters PCM Effects and Parameters PCM Effects and Parameters Data Rate 384 kb/sec AC-3 Status Display4dB Music AC-3 Effects and ParametersDolby Digital Including Surround EX THXAC-3 Effects and Parameters AC-3 Effects and Parameters DTS Music DTS 2-ChannelDTS Film DTS LogicDTS Effect Parameters DTS THXDTS Effects and Parameters Problem Possible Cause and Solution TroubleshootingTroubleshooting Exit Routine Maintenance Restoring DefaultsSpecifications Inputs Speaker Configuration circle selection

DC-2 specifications

The Lexicon DC-2 is a renowned digital surround sound processor that has garnered appreciation for its advanced technology and superior audio performance. Designed specifically for home theater systems and high-end audio setups, the DC-2 is a versatile unit that can provide high-quality sound reproduction in a variety of environments.

One of the standout features of the Lexicon DC-2 is its dual DSP architecture. This advanced processing technology enables the processor to handle complex audio formats with ease, delivering immersive soundscapes for both music and movies. The DC-2 supports formats such as Dolby Digital, DTS, and other surround sound technologies, ensuring compatibility with a wide range of media sources.

Another key characteristic of the DC-2 is its extensive connectivity options. It is equipped with multiple inputs and outputs, including analog and digital connections, which allow for seamless integration with various audio and video components. This flexibility makes it an ideal choice for those seeking to create a custom audio setup tailored to their specific needs.

The Lexicon DC-2 also features sophisticated room correction capabilities. Using the proprietary Lexicon Room Correction (LRC) technology, it analyzes the acoustic characteristics of your listening space and adjusts the audio output accordingly. This ensures optimal sound quality regardless of the room's shape or size, enhancing the overall listening experience.

Moreover, its user-friendly interface and remote control functionality offer intuitive operation, making it easy for users to navigate through different settings and modes. The LCD screen displays vital information, allowing for quick adjustments on the fly.

In terms of audio quality, the DC-2 is known for its pristine sound clarity and dynamic range. With a robust signal-to-noise ratio, it minimizes distortion and delivers a clean, accurate audio signal. Audiophiles appreciate the fidelity with which it reproduces music, bringing studio-quality sound to the home environment.

In summary, the Lexicon DC-2 is a powerful digital surround sound processor that combines advanced technologies and innovative features to provide a premier audio experience. Suitable for both casual listeners and serious audiophiles, it stands as a testament to Lexicon’s dedication to audio excellence. Its versatility, connectivity, room correction, and exceptional sound quality make the DC-2 an outstanding choice for any modern home theater system.
Top Page Image Contents