Poulan 530164256 Replace Spark Plug, Replacing the Line, Blade Replacement, Carburetor Adjustment

Page 16

REPLACE SPARK PLUG

Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch (0.6 mm). Igni- tion timing is fixed and nonadjustable.

1.Twist, then pull off spark plug boot.

2.Remove spark plug from cylinder and discard.

3.Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench.

4.Reinstall the spark plug boot.

REPLACING THE LINE

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2 feet (3.8 meters) of 0.080! (2 mm) diameter Poulan PROr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Spool

Small

Holes

Line exit holes

 

 

Line in Notch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

BLADE REPLACEMENT

Refer to the ASSEMBLY section for blade re- placement instructions and illustrations.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head, blade or any optional attachment will be spinning during most of this procedure. Wear your protective equipment and observe all safe- ty precautions. After making adjustments, the trimmer head, blade or any optional attachment must not move/spin at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is released.

S The trimmer head, blade or optional attachment moves/spins at idle.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while runningand making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without trimmer head, blade or optional attachment moving or spinning (idle too fast) or stalling (idle speed too slow).

S Turn idle speed screw clockwise to increase engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed if trimmer head, blade or optional attachment moves or spins at idle.

WARNING: Recheck the idle speed after each adjustment. The trimmer head, blade or optional attachment must not move or spin at idle speed to avoid serious injury to the operator or others.

Air Filter

Cover

Idle Speed Screw

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 530164256 11/04Operator Safety Always WearUNIT/MAINTENANCE Safety Fuel SafetyCutting Safety Transporting and StorageCarton Contents Installing Brushcutter AttachmentTools Required Attaching the HandlebarAssembly of Shoulder Strap Configuring Your UnitAssembly Information -- Trimmer Head To Relocate Shoulder Strap ClampAssembly Information -- Weed Blade Attaching the Plastic Shield and Trimmer HeadAttaching the Metal Shield Weed BladeInstallation of the Metal Blade ON/OFF Switch Choke HOW to Stop Your UnitKnow Your Unit Primer BulbHOW to Start Your Unit Switch Throttle TriggerStarting a Warm Engine Starting a Flooded EngineInstalling Optional ATTACH- Ments Operating the CouplerRemoving Trimmer ATTACH- Ment or Other Optional Attachments Operating PositionTrimmer Line Advance Cutting MethodsOperating Instructions for USE with Weed BladeWhat Causes Blade Thrust --Blade Recommended Cutting PositionEdger Safety BLOWER/VACUUM SafetyCultivator Safety Hedge Trimmer SafetyPole Pruner Safety Snow Thrower SafetyInspect and Clean Unit and DE- Cals Clean AIR FilterCheck for Loose Fasteners and Parts Check for Damaged or Worn PartsBlade Replacement Carburetor AdjustmentReplace Spark Plug Replacing the LineSeasonal Storage Fuel SystemEngine OtherTroubleshooting Table Cause Remedy Home PRODUCTS, INC., for this tool. Addi Policy of Electrolux Home ProdLigations The U.S. Environmental Electrolux Home PRODUCTS, INCUnder warranty. What is not Covered On or Modified Parts The use of add

530164256 specifications

The Poulan 530164256 is a high-performance gas chainsaw that stands out for both its reliability and efficiency, making it an excellent choice for homeowners and professionals alike. This powerful tool is designed to handle a wide range of tasks, from cutting firewood to clearing fallen trees, providing users with a robust solution for their outdoor projects.

At the heart of the Poulan 530164256 is its efficient engine. The chainsaw is equipped with a potent 42cc two-stroke engine that delivers ample power for demanding applications. This engine utilizes a lightweight design, which contributes to the overall balance of the chainsaw, enabling easy maneuverability without sacrificing performance.

One of the standout features of the Poulan 530164256 is its OxyPower technology. This innovative technology helps to increase fuel efficiency while reducing emissions, making the chainsaw more environmentally friendly. With this feature, users can enjoy longer run times and extended cutting capabilities, all while minimizing their carbon footprint.

The chainsaw also incorporates a simple starting system, which reduces the frustration often associated with starting gas-powered tools. This user-friendly ignition system ensures that users can quickly and easily fire up the chainsaw, whether they're in a hurry or dealing with cold weather conditions.

Additionally, the Poulan 530164256 features an automatic chain lubrication system. This system ensures that the chain is consistently lubricated during operation, which not only extends the lifespan of the chain and bar but also enhances cutting performance. This feature reduces the need for frequent maintenance checks, allowing users to focus on their tasks.

The chainsaw is designed with comfort in mind. It is equipped with an ergonomic handle that provides a secure grip, reducing fatigue during extended use. The anti-vibration technology further enhances user comfort by minimizing vibrations transmitted through the tool, leading to a more enjoyable cutting experience.

Overall, the Poulan 530164256 combines power, efficiency, and user-friendly features, making it an invaluable tool for anyone in need of a reliable chainsaw. Its advanced technology and thoughtful design elements make it an ideal choice for a variety of cutting tasks, ensuring that users can tackle their outdoor projects with confidence and ease.
Top Page Image Contents