Poulan 530164256 HOW to Start Your Unit, Starting a Warm Engine, Starting a Flooded Engine

Page 9

ON/OFF

Switch

Throttle Trigger

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the muffler. A hot muffler can cause serious burns.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

Starter Handle

Choke

Lever

Primer Bulb

Muffler

1.Set unit on a flat surface.

2.Move ON/OFF switch to the ON position.

3.Slowly press the primer bulb 6 times.

4.Move choke lever to FULL CHOKE by aligning lever with position shown on de- cal (see illustration below).

Choke position decal

5.Squeeze the throttle trigger fully and hold through all remaining steps.

6.Pull starter rope handle sharply until en- gine sounds as if it is trying to start, but do not pull rope more than 6 times.

7.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE by aligning lever with position shown on decal (see illustration below).

Choke position decal

8.Pull starter rope sharply until engine runs, but no more than 6 pulls. If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more than 6 pulls. If the engine doesn’t start, repeat procedure 2 additional times.

NOTE: If engine still doesn’t start, it is probably flooded. Proceed to STARTING A FLOODED ENGINE.

9.Once the engine starts, allow it to run 10 se- conds, then move the choke lever to OFF CHOKE by aligning lever with position shown on decal (see illustration below). Al- low the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trigger. NOTE: If engine dies with the choke lever in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

Choke position decal

STARTING A WARM ENGINE

1.Move ON/OFF switch to the ON position.

2.Move the choke lever to the HALF CHOKE position.

3.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the engine runs smoothly.

4.Pull starter rope sharply until engine runs, but no more than 5 pulls.

5.Allow engine to run 15 seconds, then move the choke lever to the OFF CHOKE position.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could requirepulling the starter handle many times depending on how badly the unit is flooded.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 11/04 530164256Always Wear Operator SafetyFuel Safety UNIT/MAINTENANCE SafetyCutting Safety Transporting and StorageInstalling Brushcutter Attachment Carton ContentsTools Required Attaching the HandlebarConfiguring Your Unit Assembly of Shoulder StrapAssembly Information -- Trimmer Head To Relocate Shoulder Strap ClampAttaching the Plastic Shield and Trimmer Head Assembly Information -- Weed BladeAttaching the Metal Shield Weed BladeInstallation of the Metal Blade HOW to Stop Your Unit ON/OFF Switch ChokeKnow Your Unit Primer BulbSwitch Throttle Trigger HOW to Start Your UnitStarting a Warm Engine Starting a Flooded EngineOperating the Coupler Installing Optional ATTACH- MentsRemoving Trimmer ATTACH- Ment or Other Optional Attachments Operating PositionCutting Methods Trimmer Line AdvanceUSE with Weed Blade Operating Instructions forWhat Causes Blade Thrust --Blade Recommended Cutting PositionBLOWER/VACUUM Safety Edger SafetyCultivator Safety Hedge Trimmer SafetySnow Thrower Safety Pole Pruner SafetyClean AIR Filter Inspect and Clean Unit and DE- CalsCheck for Loose Fasteners and Parts Check for Damaged or Worn PartsCarburetor Adjustment Blade ReplacementReplace Spark Plug Replacing the LineFuel System Seasonal StorageEngine OtherTroubleshooting Table Cause Remedy Policy of Electrolux Home Prod Home PRODUCTS, INC., for this tool. AddiLigations The U.S. Environmental Electrolux Home PRODUCTS, INCOn or Modified Parts The use of add Under warranty. What is not Covered

530164256 specifications

The Poulan 530164256 is a high-performance gas chainsaw that stands out for both its reliability and efficiency, making it an excellent choice for homeowners and professionals alike. This powerful tool is designed to handle a wide range of tasks, from cutting firewood to clearing fallen trees, providing users with a robust solution for their outdoor projects.

At the heart of the Poulan 530164256 is its efficient engine. The chainsaw is equipped with a potent 42cc two-stroke engine that delivers ample power for demanding applications. This engine utilizes a lightweight design, which contributes to the overall balance of the chainsaw, enabling easy maneuverability without sacrificing performance.

One of the standout features of the Poulan 530164256 is its OxyPower technology. This innovative technology helps to increase fuel efficiency while reducing emissions, making the chainsaw more environmentally friendly. With this feature, users can enjoy longer run times and extended cutting capabilities, all while minimizing their carbon footprint.

The chainsaw also incorporates a simple starting system, which reduces the frustration often associated with starting gas-powered tools. This user-friendly ignition system ensures that users can quickly and easily fire up the chainsaw, whether they're in a hurry or dealing with cold weather conditions.

Additionally, the Poulan 530164256 features an automatic chain lubrication system. This system ensures that the chain is consistently lubricated during operation, which not only extends the lifespan of the chain and bar but also enhances cutting performance. This feature reduces the need for frequent maintenance checks, allowing users to focus on their tasks.

The chainsaw is designed with comfort in mind. It is equipped with an ergonomic handle that provides a secure grip, reducing fatigue during extended use. The anti-vibration technology further enhances user comfort by minimizing vibrations transmitted through the tool, leading to a more enjoyable cutting experience.

Overall, the Poulan 530164256 combines power, efficiency, and user-friendly features, making it an invaluable tool for anyone in need of a reliable chainsaw. Its advanced technology and thoughtful design elements make it an ideal choice for a variety of cutting tasks, ensuring that users can tackle their outdoor projects with confidence and ease.
Top Page Image Contents