Husqvarna 325R, 323R manual Final setting of the idling speed T, Correctly adjusted carburetor

Page 25

MAINTENANCE

Final setting of the idling speed T

Adjust the idling speed with the screw T, If it is necessary to readjust. First turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move.

Then turn, counter- clockwise until the cutting attachment stops. A correctly adjusted idle speed setting occurs when the engine runs smoothly in every position. It should also be good margin to the rpm when the cutting attachment starts to rotate/move.

CAUTION! Contact your servicing dealer, if the idle speed

Correctly adjusted carburetor

A correctly adjusted carburetor means that the machine accelerates without hesitation and the machine 4-cycles a little at max speed. Furthermore, the cutting attachment must not rotate/move at idling. A too lean adjusted low speed needle L may cause starting difficulties and bad acceleration.

A too lean adjusted high speed needle H gives lower power = less capacity, bad acceleration and/or damage to the engine. A too rich adjustment of the two speed needles L and H gives acceleration problems or too low working speed.

Adjusting the throttle wire

setting cannot be adjusted so that the cutting attachment stops. Do not use the machine until it has been properly adjusted or repaired.

High speed needle

H

The high speed needle affects

the machine’s power, speed,

temperature and fuel

consumption. A too lean

adjustment on the high

speed needle H (the high

speed needle H is screwed in

too much) gives a too high

speed resulting in engine

damage. Do not allow the

engine to run at full speed

for more than 10 seconds.

If you cannot obtain full throttle you can adjust the throttle wire. Turning the screw (A) clockwise pushes out the throttle wire casing so that full throttle can be obtained. If the engine runs too fast at idle the throttle wire casing can be shortened by turning screw (A) anticlockwise. CAUTION! Check that the idle screw T is correctly adjusted first (see instructions under the heading Fine adjustment of the idle speed T).

5 mm

Apply full throttle and turn

 

 

 

 

 

 

 

 

 

the high speed needle H

 

 

 

 

 

 

 

 

 

slowly anticlockwise until

 

 

 

 

 

 

 

 

 

the engine runs unevenly.

 

 

 

 

 

 

 

 

 

The high speed needle H is

 

 

 

 

 

 

 

 

 

then turned slowly clockwise

 

 

 

 

 

 

 

 

 

a little until the engine runs

 

 

 

 

 

 

 

 

 

smoothly.

 

 

 

 

 

 

 

 

 

Note the engine should be

 

 

 

 

 

 

 

 

 

run unloaded when

 

 

 

 

 

 

 

 

 

adjusting the high speed

H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

needle. Therefore dismantle

 

 

 

 

 

 

 

 

 

the cutting equipment, nut,

 

 

 

 

 

 

 

 

 

support flange and disc drive

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

before adjusting the high speed needle. The high speed needle is adjusted correctly when the machine ‘splatters’ a little . If the machine smokes heavily at the same time as it ‘splatters’ heavily the adjustment is too rich.

NOTE! For optimum setting of the carburetor, contact a qualified servicing dealer who has a revolution counter at his disposal.

CAUTION! Contact your servicing dealer, if the idle speed setting cannot be adjusted so that the cutting attachment stops. Do not use the machine until it has been properly adjusted or repaired.

English – 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Operators manual EPA Symbols Symbol ExplanationContents Machine‘s safety equipment Safety InstructionsPersonal protective equipment Throttle trigger lockCutting attachment guard Stop switchAnti-vibration system Quick-releaseCutting equipment MufflerLocking nut Clearing blades are intended for cutting woodThrottle trigger lock Vibration damping system Cutting equipment Sharpening Cutting equipmentGrass blade Trimmer headFuel safety General safety instructionsStart Transport and storageGeneral working instructions Basic safety precautionsBasic clearing techniques Adjusting the harness and clearing sawDesignations Brush cutting using the saw blade Grass clearing using a grass bladeClearing‘s ABC Working methodsClearing Grass clearing using the trimmer head and plastic bladesTrimming SweepingWhat is what on the brushcutter? What is WHAT?Assembling the handlebars 323R AssemblyAssembling the handlebars Transport position, handlebarsGrass blade Guard. See Technical DataFit the appropriate guard Assembling and dismantling the two-part shaft 325RXT-series Adjusting the harness and clearing sawAssembling DismantlingFuel mixture Fuel HandlingFuelling Control before starting Start and StopStart and stop Cold engineFor throttle handles with a start throttle lock Engine is stopped by switching off the ignitionStop StartCarburetor MaintenanceCorrectly adjusted carburetor Final setting of the idling speed TAdjusting the throttle wire High speed needleCooling system MufflerAngle gear Two-part shaftFiling the grass blade Air filter Spark plugOiling the air filter Daily maintenance Maintenance scheduleWeekly maintenance Monthly maintenanceTechnical data 323R Technical DataApproved accessories Type Cutting attachment Approved accessories 323R Type Cutting attachmentCentre hole in blades Ø 25,4 mm Guard Art NoYour Warranty Rights Obligations Emission Control Warranty StatementSuper Auto Super Auto II Tri Cut Trimmy H Click Trimmy Hit Junior Trimmy Hit Pro 12 cm Trimmy SII 502 26 Page ´+H#y¶5V¨ Page 2001W51 114 00 38

325R, 323R specifications

The Husqvarna 325R and 323R are both impressive trimmers designed for users who demand power, efficiency, and durability in their landscaping equipment. These models showcase Husqvarna's commitment to quality and innovation, making them ideal for both professionals and avid gardeners.

The Husqvarna 325R features a robust 25.4cc X-Torq engine. This engine technology is designed to reduce fuel consumption and emissions, thus promoting eco-friendly gardening. The unit boasts a high power-to-weight ratio, meaning that users can handle heavier workloads without feeling fatigued. The 325R is equipped with a professional-grade gear head that enhances durability while ensuring optimal cutting performance. The trimmer shaft is straight and designed for efficient trimming in hard-to-reach areas.

On the other hand, the Husqvarna 323R also packs a powerful 25cc engine, offering a similar emphasis on reduced emissions and low fuel consumption. With its lightweight design, the 323R provides excellent maneuverability, making it suitable for residential applications as well as light professional work. This model is equipped with an efficient cutting head that utilizes a dual line system for quicker and more effective trimming.

Both models incorporate Smart Start technology, which significantly reduces the effort needed for starting the engine. This feature minimizes resistance in the starter cord, allowing users to get to work quickly. The trimmers also come with an adjustable handle, giving operators the flexibility to achieve the most comfortable grip and stance, resulting in improved control and reduced fatigue during extended use.

Additionally, both the 325R and 323R models are fitted with an anti-vibration system, enhancing comfort for longer sessions. This technology absorbs vibrations, providing a smoother operational experience. The trimmers' fuel tank is designed for extended operation, allowing users to work longer without frequent refueling.

In summary, the Husqvarna 325R and 323R stand out as reliable landscaping tools that cater to a variety of trimming tasks. Both models feature powerful engines, user-friendly technologies, and ergonomic designs that enhance comfort and efficiency. Whether you are a professional landscaper or a dedicated gardener, these trimmers are built to deliver superior performance while prioritizing user satisfaction and environmental responsibility.
Top Page Image Contents