Husqvarna 325R, 323R manual Grass blade, Guard. See Technical Data

Page 18

ASSEMBLY

Assembly of the blade and trimmer head

Assembling the blade guard and clearing blade

It is extremely important that the disc drive’s/support flange’s guide engages correctly in the cutting equipment’s centre hole when assembling the cutting equipment. Cutting equipment assembled incorrectly can result in serious and/or fatal personal injury.

!WARNING!

Do not attach any blade to the unit without proper installation of all required parts. Failure to use the proper parts can cause the blade to fly off and seriously injure the operator and/or bystanders.

Under no circumstances may the cutting equipment be used without an approved guard fitted. See the chapter “Technical data”. If the wrong guard or a defective guard is fitted this can cause serious personal injury.

IMPORTANT INFORMATION

The machine must be equipped with the correct handlebars, blade guard and harness if either a clearing blade or grass blade are to be used.

Assembling the blade guard and

grass blade

 

 

• Hook the guard (A) onto

 

 

the bracket on the shaft

 

G

and secure with 1 bolt.

 

 

F

NOTE! Use the

 

E

recommended blade

 

 

 

guard. “See Technical

 

D

data“.

 

 

 

• Fit the drive disc (B) on

 

 

the output axle.

A

B

• Turn the blade axle until

 

 

C

one of the holes in the

 

 

 

drive disc aligns with the

 

 

hole in the gear housing.

 

 

Insert the locking pin (C) in the hole so that the axle is locked.

Place the blade (D),

support cup (E) (325RX-

series/325RXT-series) and

support flange (F) on the output axle.

Fit the nut (G). The

tightening torque of the

nut is 35-50 Nm (3,5 - 5 kpm). Use the socket spanner in the tool kit. Hold the handle of the spanner as close to the blade guard as possible. The nut is tightened when the spanner is turned against the direction of rotation (left-hand thread).

18 – English

Remove the mounting plate (H). Fit the adapter

(I) and bracket (J) with the two screws (K) as shown. Fit the blade guard (A) to the adapter using the 4 screws (L) as shown.

NOTE! Use the recommended blade guard. “See Technical data“.

Fit the drive disc (B) on the output axle.

Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing.

Insert the locking pin (C) in the hole so that the axle is locked.

Place the blade (D) and support flange (F) on the output axle.

Fit the nut (G). The tightening torque of the nut is 35-50 Nm (3.5 - 5 kpm). Use the socket spanner in the tool kit. Hold the handle of the spanner as close to the blade guard as possible. The nut is tightened when the spanner is turned against the direction of rotation (left- hand thread).

When slacking off and tightening the saw blade nut, the hands may be injured by the blade teeth. Always hold your hand protected by the blade guard. This is facilitated by the use of a long box spanner. The illustration shows the area in which you should keep the box spanner.

G

F

D

B

C

Image 18
Contents Operators manual EPA Symbol Explanation SymbolsContents Personal protective equipment Safety InstructionsMachine‘s safety equipment Throttle trigger lockAnti-vibration system Stop switchCutting attachment guard Quick-releaseLocking nut MufflerCutting equipment Clearing blades are intended for cutting woodThrottle trigger lock Vibration damping system Cutting equipment Grass blade Cutting equipmentSharpening Trimmer headStart General safety instructionsFuel safety Transport and storageBasic safety precautions General working instructionsAdjusting the harness and clearing saw Basic clearing techniquesDesignations Clearing‘s ABC Grass clearing using a grass bladeBrush cutting using the saw blade Working methodsTrimming Grass clearing using the trimmer head and plastic bladesClearing SweepingWhat is WHAT? What is what on the brushcutter?Assembling the handlebars AssemblyAssembling the handlebars 323R Transport position, handlebarsGuard. See Technical Data Grass bladeFit the appropriate guard Assembling Adjusting the harness and clearing sawAssembling and dismantling the two-part shaft 325RXT-series DismantlingFuel Handling Fuel mixtureFuelling Start and stop Start and StopControl before starting Cold engineStop Engine is stopped by switching off the ignitionFor throttle handles with a start throttle lock StartMaintenance CarburetorAdjusting the throttle wire Final setting of the idling speed TCorrectly adjusted carburetor High speed needleAngle gear MufflerCooling system Two-part shaftAir filter Spark plug Filing the grass bladeOiling the air filter Weekly maintenance Maintenance scheduleDaily maintenance Monthly maintenanceTechnical Data Technical data 323RCentre hole in blades Ø 25,4 mm Approved accessories 323R Type Cutting attachmentApproved accessories Type Cutting attachment Guard Art NoEmission Control Warranty Statement Your Warranty Rights ObligationsSuper Auto Super Auto II Tri Cut Trimmy H Click Trimmy Hit Junior Trimmy Hit Pro 12 cm Trimmy SII 502 26 Page ´+H#y¶5V¨ Page 114 00 38 2001W51

325R, 323R specifications

The Husqvarna 325R and 323R are both impressive trimmers designed for users who demand power, efficiency, and durability in their landscaping equipment. These models showcase Husqvarna's commitment to quality and innovation, making them ideal for both professionals and avid gardeners.

The Husqvarna 325R features a robust 25.4cc X-Torq engine. This engine technology is designed to reduce fuel consumption and emissions, thus promoting eco-friendly gardening. The unit boasts a high power-to-weight ratio, meaning that users can handle heavier workloads without feeling fatigued. The 325R is equipped with a professional-grade gear head that enhances durability while ensuring optimal cutting performance. The trimmer shaft is straight and designed for efficient trimming in hard-to-reach areas.

On the other hand, the Husqvarna 323R also packs a powerful 25cc engine, offering a similar emphasis on reduced emissions and low fuel consumption. With its lightweight design, the 323R provides excellent maneuverability, making it suitable for residential applications as well as light professional work. This model is equipped with an efficient cutting head that utilizes a dual line system for quicker and more effective trimming.

Both models incorporate Smart Start technology, which significantly reduces the effort needed for starting the engine. This feature minimizes resistance in the starter cord, allowing users to get to work quickly. The trimmers also come with an adjustable handle, giving operators the flexibility to achieve the most comfortable grip and stance, resulting in improved control and reduced fatigue during extended use.

Additionally, both the 325R and 323R models are fitted with an anti-vibration system, enhancing comfort for longer sessions. This technology absorbs vibrations, providing a smoother operational experience. The trimmers' fuel tank is designed for extended operation, allowing users to work longer without frequent refueling.

In summary, the Husqvarna 325R and 323R stand out as reliable landscaping tools that cater to a variety of trimming tasks. Both models feature powerful engines, user-friendly technologies, and ergonomic designs that enhance comfort and efficiency. Whether you are a professional landscaper or a dedicated gardener, these trimmers are built to deliver superior performance while prioritizing user satisfaction and environmental responsibility.