Husqvarna 325R, 323R manual Air filter Spark plug, Filing the grass blade, Oiling the air filter

Page 27

MAINTENANCE

Air filter

Spark plug

The air filter should be cleaned regularly removing dust and dirt to avoid:

•carburetor malfunction

•starting problems

•reduced engine power

•unnecessary wear to engine parts

• abnormal fuel consumption

Clean the filter after every 25 hours or more regularly if operating conditions are

The condition of the spark plug is affected by:

•An incorrect carburetor setting.

•An incorrect fuel mixture (too much or faulty oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrode that may result in malfunction or starting difficulties.

0,5 mm

exceptionally dusty.

Cleaning the air filter Dismantle the air filter cover and remove the air filter. Wash in clean, warm soapy water. Ensure that the

filter is dry before refitting. An air filter used for a long period of time can never be cleaned completely. Therefore it is necessary to replace the filter from time to time with a new filter. A damaged air filter must always be replaced.

If the machine is used in dusty conditions the air filter should be soaked in oil, see the section on “Oiling the air filter“.

Oiling the air filter

Always use HUSQVARNA filter oil, order no. 503 47 73-01. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. Put the filter in a plastic bag and the pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter on the machine. Never use com- mon engine oil. This would drain through the filter quite quickly and collect in the bottom.

If the machine is low on power, difficult to start or runs poorly while idling always check the spark plug first.

If the spark plug is dirty, clean it and at the same time check that the electrode gap is 0.5 mm. The spark plug should be changed after about one month of operation or earlier if necessary.

NOTE! Always use the recommended type of spark plug. An incorrect spark plug can damage the cylinder/piston.

Filing the grass blade

!WARNING!

Always stop the engine before starting work on any part of the cutting equipment. This continues to rotate even after the throttle has been released. Ensure that the cutting equipment has stopped completely and remove the cable from the spark plug before you start to work on it.

•See the cutting

equipment’s packaging for correct filing instructions.

• The blades are sharpened using a single cut flat file.

• Sharpen all edges equally to maintain the balance of the blade.

!WARNING!

Always discard a blade that is bent, twisted, cracked, shattered or damaged in any other way. Never attempt to straighten a twisted blade for use again. Only use original blades of the prescribed type.

English – 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Operators manual EPA Symbols Symbol ExplanationContents Throttle trigger lock Safety InstructionsMachine‘s safety equipment Personal protective equipmentQuick-release Stop switchCutting attachment guard Anti-vibration systemClearing blades are intended for cutting wood MufflerCutting equipment Locking nutThrottle trigger lock Vibration damping system Cutting equipment Trimmer head Cutting equipmentSharpening Grass bladeTransport and storage General safety instructionsFuel safety StartGeneral working instructions Basic safety precautionsAdjusting the harness and clearing saw Basic clearing techniquesDesignations Working methods Grass clearing using a grass bladeBrush cutting using the saw blade Clearing‘s ABCSweeping Grass clearing using the trimmer head and plastic bladesClearing TrimmingWhat is what on the brushcutter? What is WHAT?Transport position, handlebars AssemblyAssembling the handlebars 323R Assembling the handlebarsGrass blade Guard. See Technical DataFit the appropriate guard Dismantling Adjusting the harness and clearing sawAssembling and dismantling the two-part shaft 325RXT-series AssemblingFuel Handling Fuel mixtureFuelling Cold engine Start and StopControl before starting Start and stopStart Engine is stopped by switching off the ignitionFor throttle handles with a start throttle lock StopCarburetor MaintenanceHigh speed needle Final setting of the idling speed TCorrectly adjusted carburetor Adjusting the throttle wireTwo-part shaft MufflerCooling system Angle gearAir filter Spark plug Filing the grass bladeOiling the air filter Monthly maintenance Maintenance scheduleDaily maintenance Weekly maintenanceTechnical data 323R Technical DataGuard Art No Approved accessories 323R Type Cutting attachmentApproved accessories Type Cutting attachment Centre hole in blades Ø 25,4 mmYour Warranty Rights Obligations Emission Control Warranty StatementSuper Auto Super Auto II Tri Cut Trimmy H Click Trimmy Hit Junior Trimmy Hit Pro 12 cm Trimmy SII 502 26 Page ´+H#y¶5V¨ Page 2001W51 114 00 38

325R, 323R specifications

The Husqvarna 325R and 323R are both impressive trimmers designed for users who demand power, efficiency, and durability in their landscaping equipment. These models showcase Husqvarna's commitment to quality and innovation, making them ideal for both professionals and avid gardeners.

The Husqvarna 325R features a robust 25.4cc X-Torq engine. This engine technology is designed to reduce fuel consumption and emissions, thus promoting eco-friendly gardening. The unit boasts a high power-to-weight ratio, meaning that users can handle heavier workloads without feeling fatigued. The 325R is equipped with a professional-grade gear head that enhances durability while ensuring optimal cutting performance. The trimmer shaft is straight and designed for efficient trimming in hard-to-reach areas.

On the other hand, the Husqvarna 323R also packs a powerful 25cc engine, offering a similar emphasis on reduced emissions and low fuel consumption. With its lightweight design, the 323R provides excellent maneuverability, making it suitable for residential applications as well as light professional work. This model is equipped with an efficient cutting head that utilizes a dual line system for quicker and more effective trimming.

Both models incorporate Smart Start technology, which significantly reduces the effort needed for starting the engine. This feature minimizes resistance in the starter cord, allowing users to get to work quickly. The trimmers also come with an adjustable handle, giving operators the flexibility to achieve the most comfortable grip and stance, resulting in improved control and reduced fatigue during extended use.

Additionally, both the 325R and 323R models are fitted with an anti-vibration system, enhancing comfort for longer sessions. This technology absorbs vibrations, providing a smoother operational experience. The trimmers' fuel tank is designed for extended operation, allowing users to work longer without frequent refueling.

In summary, the Husqvarna 325R and 323R stand out as reliable landscaping tools that cater to a variety of trimming tasks. Both models feature powerful engines, user-friendly technologies, and ergonomic designs that enhance comfort and efficiency. Whether you are a professional landscaper or a dedicated gardener, these trimmers are built to deliver superior performance while prioritizing user satisfaction and environmental responsibility.
Top Page Image Contents