Husqvarna 325R, 323R manual Muffler, Cooling system, Angle gear, Two-part shaft

Page 26

MAINTENANCE

Muffler

NOTE!

Some mufflers are fitted with a catalytic converter. See

“Technical data” to see whether you clearing saw is fitted with a catalytic converter.

The muffler is designed to dampen the noise level and to direct the exhaust fumes away from the user. The exhaust fumes are hot and can contain sparks, which can result in fire if the exhaust fumes are directed towards a dry and inflammable material. Some mufflers are equipped with a special spark arrest screen. If your machine is fitted with this type of screen it should be cleaned regularly. This is done using a wire brush. On mufflers without a catalytic converter the screen should be cleaned weekly, or replaced if necessary. On mufflers fitted with a catalytic converter the

Cooling system

To maintain as low opera- ting temperature as possible the engine is equipped with a cooling system.

The cooling system consists of:

1.An air intake on the starter unit.

2.Cooling fins on the flywheel.

3.Cooling fins on the cylinder

4.Cylinder cover (leads cold air onto the cylinder).

Clean the cooling system using a brush at least once a week, in difficult conditions more often.

A dirty or blocked cooling system leads to the engine overheating resulting in damage to the cylinder and piston.

4

3

2

1

screen should be checked and cleaned monthly. If the screen is damaged it should be replaced. If the screen is frequently blocked, this can be a sign that the function of the catalytic converter is impaired. Contact your dealer to inspect the muffler. A blocked screen will cause the engine to overheat resulting in damage to the cylinder and piston. Also see under “Maintenance”.

NOTE!

Never use a machine with a defective muffler.

!WARNING!

Mufflers fitted with catalytic converters become extremely hot during use and after stopping. This also applies at idling speeds. Contact can result in burns to the skin. Be observant to the risk of fire!

Angle gear

The angle gear is filled with a sufficient quantity of grease at the factory. However, before using the machine you should check that the angle gear is filled to 3/4 with grease. Use HUSQVARNA special grease.

Normally, the grease does not need to be changed except when the angle gear is repaired.

Two-part shaft

The end of the drive axle in the lower shaft should be lubricated with grease every 30 hours. There is a risk that the drive axle ends (splined coupling) on two-part shafts jam if they are not lubricated regularly.

26 – English

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Operators manual EPA Symbol Explanation SymbolsContents Personal protective equipment Safety InstructionsMachine‘s safety equipment Throttle trigger lockAnti-vibration system Stop switchCutting attachment guard Quick-releaseLocking nut MufflerCutting equipment Clearing blades are intended for cutting woodThrottle trigger lock Vibration damping system Cutting equipment Grass blade Cutting equipmentSharpening Trimmer headStart General safety instructionsFuel safety Transport and storageBasic safety precautions General working instructionsDesignations Adjusting the harness and clearing sawBasic clearing techniques Clearing‘s ABC Grass clearing using a grass bladeBrush cutting using the saw blade Working methodsTrimming Grass clearing using the trimmer head and plastic bladesClearing SweepingWhat is WHAT? What is what on the brushcutter?Assembling the handlebars AssemblyAssembling the handlebars 323R Transport position, handlebarsGuard. See Technical Data Grass bladeFit the appropriate guard Assembling Adjusting the harness and clearing sawAssembling and dismantling the two-part shaft 325RXT-series DismantlingFuelling Fuel HandlingFuel mixture Start and stop Start and StopControl before starting Cold engineStop Engine is stopped by switching off the ignitionFor throttle handles with a start throttle lock StartMaintenance CarburetorAdjusting the throttle wire Final setting of the idling speed TCorrectly adjusted carburetor High speed needleAngle gear MufflerCooling system Two-part shaftOiling the air filter Air filter Spark plugFiling the grass blade Weekly maintenance Maintenance scheduleDaily maintenance Monthly maintenanceTechnical Data Technical data 323RCentre hole in blades Ø 25,4 mm Approved accessories 323R Type Cutting attachmentApproved accessories Type Cutting attachment Guard Art NoEmission Control Warranty Statement Your Warranty Rights ObligationsSuper Auto Super Auto II Tri Cut Trimmy H Click Trimmy Hit Junior Trimmy Hit Pro 12 cm Trimmy SII 502 26 Page ´+H#y¶5V¨ Page 114 00 38 2001W51

325R, 323R specifications

The Husqvarna 325R and 323R are both impressive trimmers designed for users who demand power, efficiency, and durability in their landscaping equipment. These models showcase Husqvarna's commitment to quality and innovation, making them ideal for both professionals and avid gardeners.

The Husqvarna 325R features a robust 25.4cc X-Torq engine. This engine technology is designed to reduce fuel consumption and emissions, thus promoting eco-friendly gardening. The unit boasts a high power-to-weight ratio, meaning that users can handle heavier workloads without feeling fatigued. The 325R is equipped with a professional-grade gear head that enhances durability while ensuring optimal cutting performance. The trimmer shaft is straight and designed for efficient trimming in hard-to-reach areas.

On the other hand, the Husqvarna 323R also packs a powerful 25cc engine, offering a similar emphasis on reduced emissions and low fuel consumption. With its lightweight design, the 323R provides excellent maneuverability, making it suitable for residential applications as well as light professional work. This model is equipped with an efficient cutting head that utilizes a dual line system for quicker and more effective trimming.

Both models incorporate Smart Start technology, which significantly reduces the effort needed for starting the engine. This feature minimizes resistance in the starter cord, allowing users to get to work quickly. The trimmers also come with an adjustable handle, giving operators the flexibility to achieve the most comfortable grip and stance, resulting in improved control and reduced fatigue during extended use.

Additionally, both the 325R and 323R models are fitted with an anti-vibration system, enhancing comfort for longer sessions. This technology absorbs vibrations, providing a smoother operational experience. The trimmers' fuel tank is designed for extended operation, allowing users to work longer without frequent refueling.

In summary, the Husqvarna 325R and 323R stand out as reliable landscaping tools that cater to a variety of trimming tasks. Both models feature powerful engines, user-friendly technologies, and ergonomic designs that enhance comfort and efficiency. Whether you are a professional landscaper or a dedicated gardener, these trimmers are built to deliver superior performance while prioritizing user satisfaction and environmental responsibility.
Top Page Image Contents