Husqvarna 128C Spark plug, Air filter, Bevel gear 128L, Cleaning the air filter, Maintenance

Page 17
Spark plug

MAINTENANCE

WARNING: Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of fire!

WARNING: The inside of the muffler contain chemicals that may be carcinogenic. Avoid contact with these elements in the event of a damaged muffler.

WARNING: Bear in mind that: Engine exhaust fumes contain car- bon monoxide, which can cause carbon monoxide poisoning. For this reason you should not start or run the machine indoors, or any- where that is poorly ventilated. The exhaust fumes from the engine are hot and may contain sparks which can start a fire. Never start the machine indoors or near com- bustible material!

Spark plug

The spark plug condition is influenced by:

SIncorrect carburetor adjustment.

SAn incorrect fuel mixture (too much or in- correct type of oil).

SA dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operat- ing problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0,6 mm. The spark plug should be replaced after about a month in operation or earlier if necessary.

0,6 mm

CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

SCarburetor malfunctions S Starting problems

S Loss of engine power

S Unnecessary wear to engine parts S Excessive fuel consumption

Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty.

Cleaning the air filter

Remove the air filter cover and take out the filter. Wash it clean in warm, soapy water. Rinse thoroughly. Ensure that the filter is dry before refitting it.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

Bevel gear (128L)

The bevel gear is filled with the right quan- tity of grease at the factory. However, be- fore using the machine you should check that the bevel gear is filled three--quarters full with grease. Use HUSQVARNA special grease.

The grease in the bevel gear does not nor- mally need to be changed except if repairs are carried out.

545196741 Rev. 2 4/30/09

English--- 17

Image 17
Contents EN 2-22 FR 23-43 ES Symbols SYMBOL EXPLANATIONNote the following before starting CONTENTSContents What is what? WHAT IS WHAT?128L 128CPersonal protective equipment GENERAL SAFETY PRECAUTIONSThrottle lock-out Machine’s safety equipmentStop switch Muffler Cutting attachment guardTrimmer head Cutting equipmentFitting the loop handle ASSEMBLYFitting the trimmer guard and trimmer head Model 128L Fitting the trimmer guard and trimmer head Model 128CFUEL HANDLING Fuel safetyFuel Transport and storageMixing FuellingCheck before starting STARTING AND STOPPINGStarting and stopping Cold engineStopping Warm engineWORKING TECHNIQUES Basic safety rulesGeneral working instructions Basic working techniquesCutting ClearingSweeping Stop the machine immediately if anyone approachesUnit/Maintenance Safety MAINTENANCEBasic setting Fine adjustment of the idle speed-TSpark plug Cleaning the air filterAir filter Bevel gear 128LMaintenance Maintenance scheduleMaintenance Maintenance DailyTechnical data TECHNICAL DATACOUNCIL’S DIRECTIVES DECLARATION OF CONFORMITYEC Declaration of Conformity Only applies to Europe 6 m 20i 3 m Trimmer Head Line Loading Instructions545196741 Rev Plastic Blades Tri Cut4/30/09 English