Ryobi 825r Replacing the Spark Plug, Spark Arrestor Maintenance, ACCESSORIES/REPLACEMENT Parts

Page 24

MAINTENANCE AND REPAIR INSTRUCTIONS

REPLACING THE SPARK PLUG

Use only genuine Ryobi spark plugs. The correct air gap is 0.025 in. (0.655 mm.). Remove the plug after every 50 hours of operation and check its condition.

1.Stop the engine and allow it to cool. Grasp the plug wire firmly and pull the cap from the spark plug.

2.Clean dirt from around the spark plug. Remove the spark plug from the cylinder head by turning a 5/8 in. socket counterclockwise.

3.Replace cracked, fouled or dirty spark plug. Set the air gap at 0.025 in. (0.655 mm.) using a feeler gauge (Fig. 44).

0.025 in.

(0.655 mm.)

Fig. 44

CAUTION: Do not sand blast, scrape, or clean electrodes. Grit in the engine could damage the cylinder.

4.Install a correctly gaped spark plug in the cylinder head. Tighten by turning the 5/8 in. socket clockwise until snug.

If using a torque wrench torque to; 110-120 in.•lb. (12.3-13.5 N•m). Do not over tighten.

NOTE: A replacement spark plug Part # 180852 can be purchased from your local authorized dealer.

SPARK ARRESTOR MAINTENANCE

1.Remove the muffler cover. See Rocker Arm Clearance, Pg. 22.

2.With a flat blade screwdriver or Torx T20 bit, remove the screw attaching the spark arrestor cover to the muffler (Fig. 45).

Muffler

Spark Arrestor Screen

Tab Screw

Spark Arrestor Cover

Slot

Fig. 45

3.Pull the tab on the spark arrestor cover out of the muffler. Remove the spark arrestor cover.

4.Remove the spark arrestor screen from the spark arrestor cover.

5.Clean the spark arrestor screen with a wire brush, or replace.

6.Reinstall the spark arrestor screen, spark arrestor cover, and screw.

NOTE: A replacement spark arrestor screen Part # 180890 can be purchased from your local authorized dealer.

ACCESSORIES/REPLACEMENT PARTS

4-Cycle Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181786

Oil Fill Plug / Dipstick . . . . . . . . . . . . . . . . . . . . . 182378

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180852

Spark Arrestor Screen . . . . . . . . . . . . . . . . . . . . . 180890

Replacement Line Cartridge . . . . . . . . . . . . . . . . 181460

Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . 181465

Bump Head Knob Assembly . . . . . . . . . . . . . . . . 181468

Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181083

Shoulder Harness . . . . . . . . . . . . . . . . . . . . . . . . 682075

Click-Link Coupler . . . . . . . . . . . . . . . . . . . . . . . 181616

24

Image 24
Contents OPERATOR’S Manual Table of Contents IntroductionCalifornia Emission Regulations Spark ArrestorSymbol Meaning Safety Warnings for GAS TrimmersRules for Safe Operation Before OperatingOther Safety Warnings While OperatingSafety and International Symbols Symbolmeaning Safety Alert SymbolFor Service INFORMATION, Call Unleaded FuelON/OFF Stop Control HOT Surface WarningSharp Blade Choke Control Other optional accessories may be used with the 825r ApplicationsDecorative trimming around trees, fences, etc See list of add-ons onAssembly Instructions Adjusting the J-HANDLEOIL and Fuel Information Recommended OIL TypeAdding OIL to Crankcase Initial USE Using Blended Fuels Using Fuel AdditivesRecommended Fuel Type Fueling UnitSTARTING/STOPPING Instructions Starting InstructionsStopping Instructions Cold Start First Start of the Day or Engine Ran Out of FuelInstalling the Cutting Attachment or Add-Ons Operating InstructionsOperating the CLICK-LINKSYSTEM Removing the Cutting Attachment or Add-OnsAdjusting Trimming Line Length Holding the TrimmerTips for Best Trimming Results Maintenance and Repair Instructions Maintenance ScheduleFrequency Maintenance Required Refer to Decorative TrimmingLine Installation for the Speedspool Winding the Inner Reel With New LineInstalling a Prewound Reel Releasing the Inner ReelSpeedspool Replacement Parts Cleaning the SpeedspoolChecking the OIL Level Changing the OILAIR Filter Maintenance Cleaning the Air FilterCarburetor Adjustment Clean Air FilterAdjust Idle Speed Screw Check FuelRocker ARM Clearance Remove the rocker arm cover and gasketRocker Arms Adjusting Nuts Feeler Gauge Gasket Spark Arrestor Maintenance ACCESSORIES/REPLACEMENT PartsReplacing the Spark Plug Cleaning and Storage CleaningStorage Long Term StorageTroubleshooting U S ET I O N Specifications EnginePage Owners Warranty Responsibilities Manufacturers Warranty CoverageOPERATOR’S Manual Part no REV. a