Craftsman 358.7958 Recommended Cutting Position, Maintenance Schedule, Care, Task When To Perform

Page 13

areaswhereitisdifficulttoseethe materialbeingcutByusingtheunit. properly,theoccurrenceofblade thrustwillbereducedandtheopera- torwillbelesslikelytolosecontrol.

Do not raise the engine above your waist as the blade can come dan- gerously close to your body.

Do not swing unit with such force

that you are in danger of losing your balance.

Bring the engine to cutting speed be-

Cut only grass, weeds, and woody brush up to 1/2 inch in diameter with the weed blade. Do not let the blade

contact material it cannot cut such as stumps, rocks, fences, metal, etc., or clusters of hard, woody brush having a diameter greater than 1/2 inch.

Keep the blade sharp. A dull blade is more likely to snag and thrust.

Cut only at full throttle. The blade will have maximum cutting power and is less likely to bind or stall.

"Feed" the blade deliberately and not too rapidly. The blade can thrust away if it is fed too rapidly.

Cut only from your left to your right. Cutting on right side of the shield will throw debris away from the operator.

Use the shoulder strap and keep a firm grip on the unit with both hands. A properly adjusted shoulder strap will support the weight of the unit, freeing your arms and hands to con- trol and guide the cutting motion.

Keep feet comfortably spread apart and braced for a possible sudden, rapid thrust of unit. Do not overreach. Keep firm footing and balance.

Keep blade below waist level; it will be easier to maintain control of unit.

fore entering the material to be cut.If the blade does not turn when you squeeze the throttle trigger, make sure shaft is fully inserted into the engine. Always release the throttle trigger and allow engine to return to idle speed when not cutting. The blade should not turn while the engine is running at idle. If the blade turns at idle, do not

use your unit. Refer to the CARBURE- TOR ADJUSTMENT section or contact

your Sears Service Center.

Maintain good firm footing while using the unit. Do this by planting feet firmly in a comfortable apart position.

Cut while swinging the upper part of your body from left to right.

As you move forward to the next area to cut, be sure to maintain your balance and footing.

RECOMMENDED CUTTING POSITION

o'clock

Cut using the 2

_._1"i,._,,}2

o'clockto 4 o'clock V'r'f V,"

position of the _/' _ _ _'€'4o'clock

blade--lr

A_IkWARNING: The operator or oth-

ers must not try to clear away cut mate- rial with the engine running or the blade turning to avoid serious injury. Stop en- gine and blade before removing materi- als wrapped around blade or shaft,

MAINTENANCE SCHEDULE

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

CARE

& MAINTENANCE

TASK

WHEN

TO PERFORM

Check for loose fasteners and parts

Before

each

use

 

 

 

 

Check

for damaged

or worn parts

Before

each

use

Inspect

and clean

unit and

decals

After each use

 

Clean

air filter

 

 

 

Every

5 hours

of operation

Inspect

muffler

and

spark

arresting screen

Every

50 hours

of operation

Replace spark

plug

 

Yearly

 

 

 

13

Image 13
Contents €RAFTSMA#J Sears, Roebuck and Co., Hoffman Estates, IL TWO Year Full Warranty on Craftsman GAS BrushwackerAlways Wear UNIT/MAINTENANCE Safety Operator SafetyCutting Safety Fuel SafetyTransporting Storage Cartoncontents Head if not already installed Installation of the CuttingTo Relocate Shoulder Strap Wise. Only tighten hand tight Installation of the Metal BladeAttaching the Metal Shield Attaching the Plastic ShieldLeavethedustcupontheshaft Primer Bulb Know Your BrushwackerBefore Starting Engine ChokeHowto Stop Your Unit HOW to Start Your UnitStarting a Flooded Engine Starting a Flooded Engine Starting a Warm EngineOperating Instructions Operating PositionSweeping Trimming MowingScalping Operating Instructions for USE with Weed BladesMaintenance Maintenance ScheduleTask When To Perform Recommended Cutting PositionDecals Clean AIR FilterInspect Muffler Spark Arresting Screen Replace Spark PlugBlade Replacement Line ReplacementCarburetor Adjustment Idle Speed AdjustmentFuel System Seasonal StorageEngine OtherTrouble Where to GET Warranty SER Your Warranty Rights and OBIs Covered Repair or Replace Emission Control Warranty MAINTENANCE, Replacement and Repair of Emission REPeligro iEsta herramienta motorizada puede ser peligrosa AdvertenciaAdvertenoia Utilice SiempreNo utilice el Seguridad DEL OperadorSeguridad AL Cortar Seguridad CON EL CombustibleTransporte Y Almacenamiento Contenido DE LA Caja Aviso DE Seguridad El estar exHerramientas Necesarias MontajeInstalacion DEL Mango Para Mover LA Abrazadera DE LA Correa AL HombroInformacion DE Montaje Cabezal DE Corte Configuracion DEL AparatoMontaje DE LA Cuchilla Metauca Para Instalar EL Cabezal DEMontaje DE LA Protector Metalica Para Instalar EL Protector PlasticaMontaje DE LA Cuchilla Metalica Cuchillacon Interruptor ON/OFF Cebador Conozca SU AparatoBombeador Antes DE Poner EN Marcha EL MotorFull Choke Para Detener EL MotorPara Poner EN Marcha EL Motor Para Arrancar CON MotorPara Arrancar CON EL Motor Caliente Ranque DE Motor AhogadoOFF Choke Arranque DE Motor AhogadoCabezal DE Corte Instrucciones DE Manejo CONMetodos DE Corte Advertencia Cortadora DE Malezas Para BarrerEl Rebote de la Cuchilla es una Causas DEL Rebote DE LA Cuchilla El Rebote de laIADVERTENClA Para evitar Cronograma DE MantenimientoTarea DE Cuidado Mantenimiento Recomendaciones GeneralesInspeccione Y Limpie EL Apara To Y SUS Placas Verifique QUE no Haya Piezas Daiiadas O GastadasLimpie EL Filtro DEL Aire FijaAjuste AL Carburador Cambio DE LA CuchillaMantenga a Marcha LentaSistema DE Combustible Estacional AlmacenajeMotor OtrosTabla Diagnostica Bierta DE Garantia DEL Fabri SUS Derechos Y ObligacionesRantia DE Responsabilidad DE DEL Dueiio Como dueiho de una Fecha DEL Comienza DE LA GARECLAMACIONSicuentaustedcon manual del usuario

358.7958 specifications

The Craftsman 358.7958 is a robust and reliable gas-powered leaf blower that showcases the brand's commitment to quality and performance. Designed for both residential and commercial users, this blower is equipped with a powerful 25cc engine that delivers exceptional airspeed and airflow, making yard clean-up a breeze.

One of the standout features of the Craftsman 358.7958 is its impressive air speed capability. With air speeds of up to 230 mph, this leaf blower can easily tackle even the toughest leaves and debris. Whether you’re clearing fallen leaves in the fall or tidying up grass clippings after mowing, this model ensures efficient and effective performance.

The blower's lightweight design, weighing in at just over 9 pounds, makes it easy to maneuver and reduces operator fatigue during extended use. Additionally, the ergonomically designed handle features a comfortable grip, providing better control and enhancing user experience. The blower is also equipped with an adjustable throttle, allowing operators to easily control the speed and airflow based on the task at hand.

Another notable technology is the Craftsman Easy Start system. This feature reduces the effort needed to pull the starter cord, ensuring that users can fire up the engine with minimal hassle. This is particularly beneficial for those who may struggle with traditional starting mechanisms, making the leaf blower accessible to a wider range of users.

In terms of maintenance, the Craftsman 358.7958 is designed for easy access to key components. It comes with a simple fuel tank design for quick refueling and a tool-less air filter that makes maintenance straightforward and hassle-free. Users can enjoy peace of mind knowing that they can keep the equipment running smoothly with minimal effort.

Moreover, this gas-powered leaf blower operates with a two-stroke engine, offering a good balance between power and efficiency. Craftsman has ensured that this model meets emission standards, helping to reduce its environmental impact.

In conclusion, the Craftsman 358.7958 is an excellent choice for anyone looking for a powerful, user-friendly leaf blower. With its combination of impressive performance, ergonomic design, and easy maintenance, it stands out in the market and continues to be a favorite among homeowners and professionals alike.