Craftsman 358.7958 manual Wise. Only tighten hand tight, Attaching the Metal Shield, Blades

Page 7

3. Whileholdingthescrewdriverin position,threadtrimmerheadonto theshaftbyturningcounterclock-

wise. Only tighten hand tight!

.,t,_-- Gearbox

I

_ Dust Cup

i_).,=_ Retaining

Washer

Cutting Head I

in the side of the gearbox by rotating the dust cup. Insert a small screwdriver into aligned holes. This will keep the

shaft from turning while loosening the trimmer head. Remove the trimmer

head by turning clockwise. Remove the screwdriver. To remove the plastic

shield, loosen and remove wing nut. Pivot shield to release bracket from slot.

See iNSTALLATION OF THE CUq-i-ING HEAD and ATTACHING THE PLASTIC SHIELD for illustrations. Be sure to store

all parts and instructions for future use. Never use the trimmer head with the

metal blade installed.

ATTACHING THE METAL SHIELD

,_WARNING:

The metal shield

4.Remove the screwdriver.

ATTACHING THE PLASTIC SHIELD

_WARNING:

The shield must be

properly installed. The shield provides partial protection from the risk of thrown objects to the operator and

others and is equipped with a line lim- iter blade which cuts excess line to the

proper length. The line limiter blade (on underside of shield) is sharp and can cut you.

1.Remove wing nut from shield.

2.Insert bracket into slot on shield.

3.Pivot shield until bolt passes through hole in bracket.

4.Tighten the wing nut securely.

s_earbox_

must be properly installed on the tool anytime the tool is used with a blade. The forward tip of the metal shield

helps to reduce the occurrence of blade thrust which can cause serious

injury such as amputation to the oper- ator or bystanders. Failure to install the shield in the position shown can result in serious injury to the operator. The length of the shield must be aligned with the length of the shaft.

1.Place the metal shield under the gearbox, and align the screw holes.

,Gearbox

Shield

ASSEMBLY INFORMATION - WEED

BLADES

_WEED

BLADES

2.Insert and thread the 4 mounting screws through the holes of the gearbox and the metal shield.

Tighten evenly and securely with

the hex wrench provided.

INSTALLATION OF THE METAL

BLADE

_, WARNING: Wear protective

NOTE: Remove the trimmer head and plastic shield before attaching the metal shield and installing one of the weed blades. To remove the trimmer head, align hole in the dust cup with the hole

gloves when handling or performing maintenance on the blade to avoid inju- ry. The blade is sharp and can cut you even when it is not moving.

,_;_,WARNING: Do not use any

blades, or fastening hardware other than the washers and nuts shown in the

following illustrations. These parts must be provided by Sears, and installed as

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents €RAFTSMA#J Sears, Roebuck and Co., Hoffman Estates, IL TWO Year Full Warranty on Craftsman GAS BrushwackerAlways Wear UNIT/MAINTENANCE Safety Operator SafetyCutting Safety Fuel SafetyTransporting Storage Cartoncontents Head if not already installed Installation of the CuttingTo Relocate Shoulder Strap Attaching the Plastic Shield Installation of the Metal BladeWise. Only tighten hand tight Attaching the Metal ShieldLeavethedustcupontheshaft Choke Know Your BrushwackerPrimer Bulb Before Starting EngineHowto Stop Your Unit HOW to Start Your UnitStarting a Flooded Engine Operating Position Starting a Warm EngineStarting a Flooded Engine Operating InstructionsOperating Instructions for USE with Weed Blades MowingSweeping Trimming ScalpingRecommended Cutting Position Maintenance ScheduleMaintenance Task When To PerformReplace Spark Plug Clean AIR FilterDecals Inspect Muffler Spark Arresting ScreenIdle Speed Adjustment Line ReplacementBlade Replacement Carburetor AdjustmentOther Seasonal StorageFuel System EngineTrouble Where to GET Warranty SER Your Warranty Rights and OBIs Covered Repair or Replace Emission Control Warranty MAINTENANCE, Replacement and Repair of Emission REPeligro iEsta herramienta motorizada puede ser peligrosa AdvertenciaSeguridad DEL Operador Utilice SiempreAdvertenoia No utilice elSeguridad AL Cortar Seguridad CON EL CombustibleTransporte Y Almacenamiento Contenido DE LA Caja Aviso DE Seguridad El estar exPara Mover LA Abrazadera DE LA Correa AL Hombro MontajeHerramientas Necesarias Instalacion DEL MangoPara Instalar EL Cabezal DE Configuracion DEL AparatoInformacion DE Montaje Cabezal DE Corte Montaje DE LA Cuchilla MetaucaMontaje DE LA Protector Metalica Para Instalar EL Protector PlasticaMontaje DE LA Cuchilla Metalica Cuchillacon Antes DE Poner EN Marcha EL Motor Conozca SU AparatoInterruptor ON/OFF Cebador BombeadorPara Arrancar CON Motor Para Detener EL MotorFull Choke Para Poner EN Marcha EL MotorArranque DE Motor Ahogado Ranque DE Motor AhogadoPara Arrancar CON EL Motor Caliente OFF ChokeCabezal DE Corte Instrucciones DE Manejo CONMetodos DE Corte Advertencia Causas DEL Rebote DE LA Cuchilla El Rebote de la Para BarrerCortadora DE Malezas El Rebote de la Cuchilla es unaRecomendaciones Generales Cronograma DE MantenimientoIADVERTENClA Para evitar Tarea DE Cuidado MantenimientoFija Verifique QUE no Haya Piezas Daiiadas O GastadasInspeccione Y Limpie EL Apara To Y SUS Placas Limpie EL Filtro DEL AireMarcha Lenta Cambio DE LA CuchillaAjuste AL Carburador Mantenga aOtros Estacional AlmacenajeSistema DE Combustible MotorTabla Diagnostica Fecha DEL Comienza DE LA GA SUS Derechos Y ObligacionesBierta DE Garantia DEL Fabri Rantia DE Responsabilidad DE DEL Dueiio Como dueiho de unaRECLAMACIONSicuentaustedcon manual del usuario

358.7958 specifications

The Craftsman 358.7958 is a robust and reliable gas-powered leaf blower that showcases the brand's commitment to quality and performance. Designed for both residential and commercial users, this blower is equipped with a powerful 25cc engine that delivers exceptional airspeed and airflow, making yard clean-up a breeze.

One of the standout features of the Craftsman 358.7958 is its impressive air speed capability. With air speeds of up to 230 mph, this leaf blower can easily tackle even the toughest leaves and debris. Whether you’re clearing fallen leaves in the fall or tidying up grass clippings after mowing, this model ensures efficient and effective performance.

The blower's lightweight design, weighing in at just over 9 pounds, makes it easy to maneuver and reduces operator fatigue during extended use. Additionally, the ergonomically designed handle features a comfortable grip, providing better control and enhancing user experience. The blower is also equipped with an adjustable throttle, allowing operators to easily control the speed and airflow based on the task at hand.

Another notable technology is the Craftsman Easy Start system. This feature reduces the effort needed to pull the starter cord, ensuring that users can fire up the engine with minimal hassle. This is particularly beneficial for those who may struggle with traditional starting mechanisms, making the leaf blower accessible to a wider range of users.

In terms of maintenance, the Craftsman 358.7958 is designed for easy access to key components. It comes with a simple fuel tank design for quick refueling and a tool-less air filter that makes maintenance straightforward and hassle-free. Users can enjoy peace of mind knowing that they can keep the equipment running smoothly with minimal effort.

Moreover, this gas-powered leaf blower operates with a two-stroke engine, offering a good balance between power and efficiency. Craftsman has ensured that this model meets emission standards, helping to reduce its environmental impact.

In conclusion, the Craftsman 358.7958 is an excellent choice for anyone looking for a powerful, user-friendly leaf blower. With its combination of impressive performance, ergonomic design, and easy maintenance, it stands out in the market and continues to be a favorite among homeowners and professionals alike.
Top Page Image Contents