Craftsman 358.7958 manual Line Replacement, Blade Replacement, Carburetor Adjustment

Page 15

LINE REPLACEMENT

•Always use Craftsman replacement line.

Choose the line size best suited for the job at hand. Red line is designed for cutting grass and small weeds.

The black colored line is designed for cutting larger weeds and light brush. NOTE: Before inserting new line into the holes in the cutting head, identify the proper holes. Follow directions as shown on the line glide plate.

1.Remove the old line and line glide plate from the cutting head.

2.Clean entire surface of cutting head.

3.Reinstall line glide plate (see il- lustration). Align arrowwith:

when using medium (red) or (_) large (black) line

when using lines with diameter (_ smaller than medium (red) line

(optional)

Line glide Arrow

Cutting head

NOTE: Line glide plate must be rein-

stalled in cutting head before inserting new line.

4.Insert both ends of your line through the proper holes in the side of the cutting head.

5.Pull the line and make sure the

line is against the hub and ex-

tended full through the positioning tunnels.

Line against

Positioning

Tunnel \

6.Correctly installed line will be the same length on both ends

BLADE REPLACEMENT

Refer to tile ASSEMBLY section for

blade replacement instructions and illustrations.

CARBURETOR ADJUSTMENT

'_&WARNING: Keep others away

when making idle speed adjustments. The trimmer head or blade will be

spinning during most of this proce- dure. Wear your protective equipment and observe all safety precautions. After making adjustments, the trimmer head or blade must not move/spin at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the fol- lowing conditions:

•Engine will not idle when the throttle is released.

•The trimmer head or blade moves/ spins at idle.

Make adjustments with the unit sup- ported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making adjust- ments. Keep all parts of your body

away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without trimmer head or blade moving or spinning (idle too fast) or engine stalling (idle speed too slow).

•Turn idle speed screw clockwise to

increase engine speed if engine stalls or dies.

•Turn idle speed screw counterclock-

wise to decrease engine speed if trimmer head or blade moves or

spins at idle.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents €RAFTSMA#J TWO Year Full Warranty on Craftsman GAS Brushwacker Sears, Roebuck and Co., Hoffman Estates, ILAlways Wear UNIT/MAINTENANCE Safety Operator SafetyFuel Safety Cutting SafetyTransporting Storage Cartoncontents Installation of the Cutting Head if not already installedTo Relocate Shoulder Strap Attaching the Plastic Shield Installation of the Metal BladeWise. Only tighten hand tight Attaching the Metal ShieldLeavethedustcupontheshaft Choke Know Your BrushwackerPrimer Bulb Before Starting EngineHOW to Start Your Unit Howto Stop Your UnitStarting a Flooded Engine Operating Position Starting a Warm EngineStarting a Flooded Engine Operating InstructionsOperating Instructions for USE with Weed Blades MowingSweeping Trimming ScalpingRecommended Cutting Position Maintenance ScheduleMaintenance Task When To PerformReplace Spark Plug Clean AIR FilterDecals Inspect Muffler Spark Arresting ScreenIdle Speed Adjustment Line ReplacementBlade Replacement Carburetor AdjustmentOther Seasonal StorageFuel System EngineTrouble Your Warranty Rights and OB Where to GET Warranty SERIs Covered Repair or Replace Emission Control Warranty MAINTENANCE, Replacement and Repair of Emission REPeligro iEsta herramienta motorizada puede ser peligrosa AdvertenciaSeguridad DEL Operador Utilice SiempreAdvertenoia No utilice elSeguridad CON EL Combustible Seguridad AL CortarTransporte Y Almacenamiento Contenido DE LA Caja Aviso DE Seguridad El estar exPara Mover LA Abrazadera DE LA Correa AL Hombro MontajeHerramientas Necesarias Instalacion DEL MangoPara Instalar EL Cabezal DE Configuracion DEL AparatoInformacion DE Montaje Cabezal DE Corte Montaje DE LA Cuchilla MetaucaPara Instalar EL Protector Plastica Montaje DE LA Protector MetalicaMontaje DE LA Cuchilla Metalica Cuchillacon Antes DE Poner EN Marcha EL Motor Conozca SU AparatoInterruptor ON/OFF Cebador BombeadorPara Arrancar CON Motor Para Detener EL MotorFull Choke Para Poner EN Marcha EL MotorArranque DE Motor Ahogado Ranque DE Motor AhogadoPara Arrancar CON EL Motor Caliente OFF ChokeInstrucciones DE Manejo CON Cabezal DE CorteMetodos DE Corte Advertencia Causas DEL Rebote DE LA Cuchilla El Rebote de la Para BarrerCortadora DE Malezas El Rebote de la Cuchilla es unaRecomendaciones Generales Cronograma DE MantenimientoIADVERTENClA Para evitar Tarea DE Cuidado MantenimientoFija Verifique QUE no Haya Piezas Daiiadas O GastadasInspeccione Y Limpie EL Apara To Y SUS Placas Limpie EL Filtro DEL AireMarcha Lenta Cambio DE LA CuchillaAjuste AL Carburador Mantenga aOtros Estacional AlmacenajeSistema DE Combustible MotorTabla Diagnostica Fecha DEL Comienza DE LA GA SUS Derechos Y ObligacionesBierta DE Garantia DEL Fabri Rantia DE Responsabilidad DE DEL Dueiio Como dueiho de unaRECLAMACIONSicuentaustedcon manual del usuario

358.7958 specifications

The Craftsman 358.7958 is a robust and reliable gas-powered leaf blower that showcases the brand's commitment to quality and performance. Designed for both residential and commercial users, this blower is equipped with a powerful 25cc engine that delivers exceptional airspeed and airflow, making yard clean-up a breeze.

One of the standout features of the Craftsman 358.7958 is its impressive air speed capability. With air speeds of up to 230 mph, this leaf blower can easily tackle even the toughest leaves and debris. Whether you’re clearing fallen leaves in the fall or tidying up grass clippings after mowing, this model ensures efficient and effective performance.

The blower's lightweight design, weighing in at just over 9 pounds, makes it easy to maneuver and reduces operator fatigue during extended use. Additionally, the ergonomically designed handle features a comfortable grip, providing better control and enhancing user experience. The blower is also equipped with an adjustable throttle, allowing operators to easily control the speed and airflow based on the task at hand.

Another notable technology is the Craftsman Easy Start system. This feature reduces the effort needed to pull the starter cord, ensuring that users can fire up the engine with minimal hassle. This is particularly beneficial for those who may struggle with traditional starting mechanisms, making the leaf blower accessible to a wider range of users.

In terms of maintenance, the Craftsman 358.7958 is designed for easy access to key components. It comes with a simple fuel tank design for quick refueling and a tool-less air filter that makes maintenance straightforward and hassle-free. Users can enjoy peace of mind knowing that they can keep the equipment running smoothly with minimal effort.

Moreover, this gas-powered leaf blower operates with a two-stroke engine, offering a good balance between power and efficiency. Craftsman has ensured that this model meets emission standards, helping to reduce its environmental impact.

In conclusion, the Craftsman 358.7958 is an excellent choice for anyone looking for a powerful, user-friendly leaf blower. With its combination of impressive performance, ergonomic design, and easy maintenance, it stands out in the market and continues to be a favorite among homeowners and professionals alike.
Top Page Image Contents