Craftsman 358.7958 manual To Relocate Shoulder Strap, Installation of the Cutting

Page 6

TO RELOCATE SHOULDER STRAP

CLAMP:

1.Loosen and remove both clamp screws.

2.Place the upper shoulder strap clamp over the shaft.

3.Position the lower shoulder strap clamp under the shaft and align

the upper and lower clamp screw holes.

Upper Shoulder

Clamp

Lower

Shoulder

l

Strap

Clamp

Screws

 

 

4.Insert two screws into the screw holes.

5.Secure shoulder strap clamp by

tightening screws with a hex wrench.

HARNESS

ADJUSTMENT

FOR BALANCE

6 inches

4 -12

below

waist

inches

above

 

30 inches

ground

I

30i

CONFIGURING YOUR UNIT

You can configure your unit using a cut- ting head for grass and light weeds, or a weed blade for cutting grass, weeds, and brush up to 1/2 inch in diameter. To assemble your unit, go to the section for

the desired configuration and follow the instructions.

ASSEMBLY INFORMATION - TRIMMER HEAD

::_TRIMMER

NOTE: Remove the blade and metal shield before attaching the plastic shield and trimmer head. To remove blade, align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup. Insert a small screwdriv- er into aligned holes. This will keep the

shaft from turning while loosening the

blade nut. Remove blade nut by turning clockwise. Remove the screwdriver.

Remove both washers and blade. To remove metal shield, loosen and re-

move the four mounting screws. See ATTACHING THE METAL SHIELD and

INSTALLATIONOF THE METAL BLADE for

illustrations. Be sure to store all parts and instructions for future use.

INSTALLATION OF THE CUTTING

HEAD (if not already installed)

NOTE: Before installing the trimmer head, make sure the dust cup and re- taining washer are positioned on the shaft of the gearbox. The retaining washer must be positioned with the raised section toward the gearbox.

1.Align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup.

2.Insert a small screwdriver into aligned holes. This will keep the

shaft from turning while tightening trimmer head.

Screwier _

Page 5 Page 7
Image 6
Page 5 Page 7
Contents €RAFTSMA#J TWO Year Full Warranty on Craftsman GAS Brushwacker Sears, Roebuck and Co., Hoffman Estates, ILAlways Wear Operator Safety UNIT/MAINTENANCE SafetyFuel Safety Cutting SafetyTransporting Storage Cartoncontents Installation of the Cutting Head if not already installedTo Relocate Shoulder Strap Attaching the Metal Shield Installation of the Metal BladeWise. Only tighten hand tight Attaching the Plastic ShieldLeavethedustcupontheshaft Before Starting Engine Know Your BrushwackerPrimer Bulb ChokeHOW to Start Your Unit Howto Stop Your UnitStarting a Flooded Engine Operating Instructions Starting a Warm EngineStarting a Flooded Engine Operating PositionScalping MowingSweeping Trimming Operating Instructions for USE with Weed BladesTask When To Perform Maintenance ScheduleMaintenance Recommended Cutting PositionInspect Muffler Spark Arresting Screen Clean AIR FilterDecals Replace Spark PlugCarburetor Adjustment Line ReplacementBlade Replacement Idle Speed AdjustmentEngine Seasonal StorageFuel System OtherTrouble Your Warranty Rights and OB Where to GET Warranty SERIs Covered Repair or Replace MAINTENANCE, Replacement and Repair of Emission RE Emission Control WarrantyAdvertencia Peligro iEsta herramienta motorizada puede ser peligrosaNo utilice el Utilice SiempreAdvertenoia Seguridad DEL OperadorSeguridad CON EL Combustible Seguridad AL CortarTransporte Y Almacenamiento Aviso DE Seguridad El estar ex Contenido DE LA CajaInstalacion DEL Mango MontajeHerramientas Necesarias Para Mover LA Abrazadera DE LA Correa AL HombroMontaje DE LA Cuchilla Metauca Configuracion DEL AparatoInformacion DE Montaje Cabezal DE Corte Para Instalar EL Cabezal DEPara Instalar EL Protector Plastica Montaje DE LA Protector MetalicaMontaje DE LA Cuchilla Metalica Cuchillacon Bombeador Conozca SU AparatoInterruptor ON/OFF Cebador Antes DE Poner EN Marcha EL MotorPara Poner EN Marcha EL Motor Para Detener EL MotorFull Choke Para Arrancar CON MotorOFF Choke Ranque DE Motor AhogadoPara Arrancar CON EL Motor Caliente Arranque DE Motor AhogadoInstrucciones DE Manejo CON Cabezal DE CorteMetodos DE Corte Advertencia El Rebote de la Cuchilla es una Para BarrerCortadora DE Malezas Causas DEL Rebote DE LA Cuchilla El Rebote de laTarea DE Cuidado Mantenimiento Cronograma DE MantenimientoIADVERTENClA Para evitar Recomendaciones GeneralesLimpie EL Filtro DEL Aire Verifique QUE no Haya Piezas Daiiadas O GastadasInspeccione Y Limpie EL Apara To Y SUS Placas FijaMantenga a Cambio DE LA CuchillaAjuste AL Carburador Marcha LentaMotor Estacional AlmacenajeSistema DE Combustible OtrosTabla Diagnostica Rantia DE Responsabilidad DE DEL Dueiio Como dueiho de una SUS Derechos Y ObligacionesBierta DE Garantia DEL Fabri Fecha DEL Comienza DE LA GARECLAMACIONSicuentaustedcon manual del usuario

358.7958 specifications

The Craftsman 358.7958 is a robust and reliable gas-powered leaf blower that showcases the brand's commitment to quality and performance. Designed for both residential and commercial users, this blower is equipped with a powerful 25cc engine that delivers exceptional airspeed and airflow, making yard clean-up a breeze.

One of the standout features of the Craftsman 358.7958 is its impressive air speed capability. With air speeds of up to 230 mph, this leaf blower can easily tackle even the toughest leaves and debris. Whether you’re clearing fallen leaves in the fall or tidying up grass clippings after mowing, this model ensures efficient and effective performance.

The blower's lightweight design, weighing in at just over 9 pounds, makes it easy to maneuver and reduces operator fatigue during extended use. Additionally, the ergonomically designed handle features a comfortable grip, providing better control and enhancing user experience. The blower is also equipped with an adjustable throttle, allowing operators to easily control the speed and airflow based on the task at hand.

Another notable technology is the Craftsman Easy Start system. This feature reduces the effort needed to pull the starter cord, ensuring that users can fire up the engine with minimal hassle. This is particularly beneficial for those who may struggle with traditional starting mechanisms, making the leaf blower accessible to a wider range of users.

In terms of maintenance, the Craftsman 358.7958 is designed for easy access to key components. It comes with a simple fuel tank design for quick refueling and a tool-less air filter that makes maintenance straightforward and hassle-free. Users can enjoy peace of mind knowing that they can keep the equipment running smoothly with minimal effort.

Moreover, this gas-powered leaf blower operates with a two-stroke engine, offering a good balance between power and efficiency. Craftsman has ensured that this model meets emission standards, helping to reduce its environmental impact.

In conclusion, the Craftsman 358.7958 is an excellent choice for anyone looking for a powerful, user-friendly leaf blower. With its combination of impressive performance, ergonomic design, and easy maintenance, it stands out in the market and continues to be a favorite among homeowners and professionals alike.
Top Page Image Contents