Snapper ERP2187519BV, EP2187519BV Maintenance Maintenance Introduction, Change Engine Oil

Page 14

Maintenance

Maintenance - Introduction

To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention the model and serial number.

Check Grease Level in Transmission

1.Remove the transmission fill plug (A, Figure 15). Roll the machine forward or backward while looking down into the plug hole.

2.If liquid grease is not visible on the input gear (the small gear below the plug hole), add an amount, to cover the gear, of Snapper “00” grease.

Maintenance

!

WARNING

!

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

Service - After First 5 Hours

Change Engine Oil

1.Refer to the Engine Manual for proper oil specifications, procedures and proper service intervals.

2.For the simplest/cleanest oil change, simply turn the mower on its side to drain the oil, as shown. Drain the oil through the dipstick tube (A, Figure 14) into a container. Allow sufficient time for all the oil to drain.

Important: Drain the fuel tank before tipping the machine. DO NOT tip the machine with the carburetor or spark plug down. Oil from the crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

A

Figure 14: Draining the engine oil

3.Dispose of drain oil properly.

4.Fill the engine with oil as specified in the Engine Manual. Do not overfill.

A

Figure 15: Removing the transmission fill plug

Note: Snapper “00” grease (Part No. 7029443) is available at your Snapper dealer.

Note: Do not spill grease or oil onto the surface of the drive disc (A, Figure 16).

A

Figure 16: Location of the drive disc

3.Reinstall the transmission plug.

4.Check the grease level after each 25 hours of operation.

Important: Drain the fuel tank before tipping the mower. DO NOT tip the machine with the carburetor or spark plug down. Oil from the crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

12

www.snapper.com

Page 13 Page 15
Image 14
Page 13 Page 15
Contents European 21 Steel Deck Walk Mowers Series Date of Purchase Retailer Retailers Phone Number Equipment EngineTable of Contents Preparation From Previous Column Protection for ChildrenSlope Operation PreparationOperation Maintenance and StorageSafe Handling of Gasoline From Previous Operation From Previous ColumnDecal Identification MCDONOUGH, GA 30253 USAOperator Safety Engine Speed Control Features and Controls Features and ControlsEngine and Blade Operation Pre-Start Check ListStarting and Operation Propelling the Mower OperationStopping Removing the Recycling Cover Cutting Height AdjustmentRecycling Operation Installing the Discharge Deflector Installing the Grass Bag AdapterInstalling the Recycling Plug Installing the Grass BagCheck Grease Level in Transmission Maintenance Maintenance IntroductionService After First 5 Hours Change Engine OilStorage Procedure MaintenanceService Periodic Ninja Blade Wear Limit Mower Blade ReplacementStandard Blade Wear Limit Blade SharpeningWheel Drive Control Adjustment Sharpening the mower bladeDrive Spring Repair/Replacement Driven and Drive Disc ServiceCleaning Drive Disc & Driven Disc Driven Disc AdjustmentDriven Disc Replacement Adjusting the driven discDriven Disc Bearing Replacement Removing the driven disc assemblyReplacing the Bearing On the Pulley End Of the Hex Shaft Belt ServiceEngine Drive Belt Replacement Stretch Type Belts Transmission Poly-V Belt Replacement ProcedureService Schedule Maintenance/Replacement PartsTroubleshooting Probable Cause Corrective ActionYear Limited Warranty Page Page Page Page Page Page Product Specifications Common Service Parts European

ERP2187519BV, EP2187519BV specifications

The Snapper ERP2187519BV, also known as EP2187519BV, is a highly versatile and efficient piece of equipment designed to meet the demanding needs of various industries. This model is known for its reliability, ease of use, and advanced features that streamline operations and enhance productivity.

One of the key features of the Snapper ERP2187519BV is its robust construction. Designed with durability in mind, it can withstand heavy usage in tough environments, making it an ideal choice for industrial applications. The equipment is made from high-quality materials that resist wear and tear, ensuring longevity and reducing maintenance costs.

The Snapper ERP2187519BV is equipped with a powerful motor that offers efficient performance and optimal energy consumption. The motor is designed to deliver consistent power output, allowing users to complete tasks more quickly and effectively. This efficiency not only improves productivity but also results in lower operating costs.

In terms of technology, the Snapper ERP2187519BV features advanced control systems that enable precise operation. The user interface is intuitive, providing operators with easy access to various settings and operational modes. This allows for quick adjustments to be made, accommodating different tasks and environments seamlessly.

Another standout characteristic of the Snapper ERP2187519BV is its versatility. It comes with multiple attachments and accessories that can be easily swapped out, allowing it to perform a wide range of functions. Whether for landscaping, maintenance, or construction, the flexibility of this equipment makes it a valuable asset in any workflow.

Additionally, the Snapper ERP2187519BV emphasizes user comfort and safety. With ergonomic designs and safety features integrated into its operation, users can work more comfortably and securely. This consideration for the operator’s experience enhances productivity while minimizing the risk of accidents.

Overall, the Snapper ERP2187519BV stands out in the market for its combination of durability, advanced technology, versatility, and user-friendly design. It is engineered to help professionals tackle various challenges efficiently, making it an indispensable tool in today’s fast-paced industrial landscape. Whether used in small businesses or large enterprises, it meets the high standards of performance and reliability that users demand.
Top Page Image Contents