Snapper ERP2187519BV, EP2187519BV specifications Maintenance, Service Periodic, Storage Procedure

Page 15

Maintenance (Continued)

!

WARNING

!

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

Check Mower Blade

1.Disconnect the spark plug wire and secure the end away from the plug.

2.Tilt the mower up on its rear wheels for access to the blade cap screw (A, Figure 17). Do not tilt the mower with the spark plug or carburetor down.

Important: Drain the fuel tank before tipping the mower. DO NOT tip the machine with the carburetor or spark plug down. Oil from the crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

3.Check the torque of the blade cap screw. Recommended torque should be 40 ft. lbs.

4.Check the blade for sharpness, wear and damage. Refer to the Section entitled “Blade Wear Limits”.

A

Figure 17: Tightening the blade cap screw

Check Transmission Poly-V Belt

1.Visually check the poly-v belt for cracking, fraying, sev- ered or exposed belt strands. If worn or damaged, replace the belt before operating the mower.

Service - Periodic

Perform all maintenance as described in the “Service Schedule” section of this manual.

Engine

Service the engine according to the engine owner’s manual.

Air Filter

Refer to the engine owner’s manual for service instructions.

Engine Oil

Refer to the engine owner’s manual for service instructions.

Storage Procedure

Refer to the Engine Owner’s Manual for directions regarding engine storage preparations. Prepare the mower for “end of season” storage as follows:

1.Drain the fuel from the fuel tank and let the engine run until all fuel is out of the carburetor.

2.Disconnect and remove the spark plug wire away from the spark plug before any other preparations are made!

3.Tape all openings closed to prevent spraying water into the exhaust or air intakes during washing.

4.Tilt the mower up on its rear wheels and thoroughly clean the underside of the deck. Do not tilt the mower with the spark plug or carburetor down. Scrape away any accumulation of grass with a putty knife and/or wire brush.

5.Lubricate all exposed metal with a light coating of oil to prevent corrosion.

6.On self-propelled models, disconnect the transfer rod clip and remove the ground speed control rod before folding the handles.

7.Loosen the handle knobs. Carefully fold the handles forward, “flexing” the control cables to prevent cable damage.

8.Store the mower in a shed or other dry area, protected from weather.

Maintenance

Check Engine Drive Belt

1.Visually check the engine drive belt for cracking, fraying, severed or exposed belt strands. If worn or damaged, replace the belt before operating the mower.

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents European 21 Steel Deck Walk Mowers Series Engine Date of Purchase Retailer Retailers Phone Number EquipmentTable of Contents Preparation Protection for ChildrenSlope Operation Preparation From Previous ColumnOperation From Previous Column Maintenance and StorageSafe Handling of Gasoline From Previous OperationMCDONOUGH, GA 30253 USA Decal IdentificationOperator Safety Engine Speed Control Features and Controls Features and ControlsOperation Pre-Start Check List Starting and OperationEngine and Blade Operation StoppingPropelling the Mower Cutting Height Adjustment Recycling OperationRemoving the Recycling Cover Installing the Grass Bag Adapter Installing the Discharge DeflectorInstalling the Grass Bag Installing the Recycling PlugChange Engine Oil Maintenance Maintenance IntroductionService After First 5 Hours Check Grease Level in TransmissionMaintenance Service PeriodicStorage Procedure Blade Sharpening Mower Blade ReplacementStandard Blade Wear Limit Ninja Blade Wear LimitSharpening the mower blade Wheel Drive Control AdjustmentDriven Disc Adjustment Driven and Drive Disc ServiceCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementAdjusting the driven disc Driven Disc ReplacementRemoving the driven disc assembly Driven Disc Bearing ReplacementBelt Service Engine Drive Belt Replacement Stretch Type BeltsReplacing the Bearing On the Pulley End Of the Hex Shaft Procedure Transmission Poly-V Belt ReplacementMaintenance/Replacement Parts Service ScheduleProbable Cause Corrective Action TroubleshootingYear Limited Warranty Page Page Page Page Page Page European Product Specifications Common Service Parts

ERP2187519BV, EP2187519BV specifications

The Snapper ERP2187519BV, also known as EP2187519BV, is a highly versatile and efficient piece of equipment designed to meet the demanding needs of various industries. This model is known for its reliability, ease of use, and advanced features that streamline operations and enhance productivity.

One of the key features of the Snapper ERP2187519BV is its robust construction. Designed with durability in mind, it can withstand heavy usage in tough environments, making it an ideal choice for industrial applications. The equipment is made from high-quality materials that resist wear and tear, ensuring longevity and reducing maintenance costs.

The Snapper ERP2187519BV is equipped with a powerful motor that offers efficient performance and optimal energy consumption. The motor is designed to deliver consistent power output, allowing users to complete tasks more quickly and effectively. This efficiency not only improves productivity but also results in lower operating costs.

In terms of technology, the Snapper ERP2187519BV features advanced control systems that enable precise operation. The user interface is intuitive, providing operators with easy access to various settings and operational modes. This allows for quick adjustments to be made, accommodating different tasks and environments seamlessly.

Another standout characteristic of the Snapper ERP2187519BV is its versatility. It comes with multiple attachments and accessories that can be easily swapped out, allowing it to perform a wide range of functions. Whether for landscaping, maintenance, or construction, the flexibility of this equipment makes it a valuable asset in any workflow.

Additionally, the Snapper ERP2187519BV emphasizes user comfort and safety. With ergonomic designs and safety features integrated into its operation, users can work more comfortably and securely. This consideration for the operator’s experience enhances productivity while minimizing the risk of accidents.

Overall, the Snapper ERP2187519BV stands out in the market for its combination of durability, advanced technology, versatility, and user-friendly design. It is engineered to help professionals tackle various challenges efficiently, making it an indispensable tool in today’s fast-paced industrial landscape. Whether used in small businesses or large enterprises, it meets the high standards of performance and reliability that users demand.
Top Page Image Contents